![Mono Omega Plus 400 (твердое тесто) Инструкция по эксплуатации онлайн [2/70] 279326](/img/pdf.png)
Mono Omega Plus 400 (твердое тесто) Инструкция по эксплуатации онлайн [2/70] 279326
![Mono Omega Plus 400 (твердое тесто) Инструкция по эксплуатации онлайн [2/70] 279326](/views2/1334008/page2/bg2.png)
Содержание
- Depositor 400 450 1
- Manual 1
- Omega plus 1
- Operating and maintenance 1
- Failure to adhere to the cleaning and maintenance instructions detailed in this booklet could affect the warranty of this machine 3
- Contents 4
- Operating instructions 4
- Preparing for operation 4
- Introduction 5
- Dimensions 6
- Models are available with or without wirecut option 6
- Omega plus 6
- Specifications 7
- Safety 8
- All cleaning and maintenance operations must 9
- Be made with the machine disconnected from 9
- The power supply 9
- In an emergency switch off at the in an emergency switch off at the electrical mains wall isolator or push the emergency stop button 10
- Installation 10
- Isolation 10
- Stop button 10
- To release the emergency stop button turn clockwise 10
- Cleaning instructions 11
- Hard and soft dough hoppers 11
- Soft dough hopper 13
- Do not leave any components in the hopper 14
- Hard dough hopper 14
- Operating conditions 15
- Preparing for operation 16
- A fitting the hopper 17
- Do not operate machine without template fitted 17
- B fitting a template soft dough 18
- Do not operate machine without template fitted 18
- Before using straight offset nozzle holders 19
- O rings must be fitted 19
- Do not operate machine without template fitted 20
- Hard dough 20
- Fitting wirecut fingers 21
- If wirecut fitted 21
- If wirecut fitted 22
- Replacing broken wire 22
- Omega plus operation 23
- Change settings 24
- For following instructions 24
- If a grey box is shown in the button description e g go to the corresponding page further on in the instructions marked in top right hand corner of each page 24
- Operating key 24
- Operation 24
- Select product type 25
- Then to move to the next screen 25
- To create a new program 25
- Touch the screen for the type of product required 25
- Select saved product type 26
- To create new program 26
- Confirm setup of machine 27
- Machine is set as shown on the screen this screen controls the actions required by the operator 28
- Operator screen 28
- Program 28
- Start manual 28
- Start stop 28
- Drop with twist 29
- Edit and save screen 29
- Example drop with twist 29
- Save edits 29
- Example 30
- Multidrop with twist 30
- Other setting buttons are the same as last page 30
- Sheeting strip 30
- Example c shape arc 31
- Number of rows per 32
- Tray edge height mm 32
- Tray length mm 32
- Tray setup 32
- Delete 34
- Caution 35
- Diagnostics 35
- Do not attempt to make adjustments unless you are fully aware of the results 35
- Engineering settings 35
- Passwords 35
- Reset factory defaults 35
- Screen adjustment 35
- Caution 36
- Engineering settings 36
- Caution 37
- Engineering settings 37
- Caution 38
- Engineering settings 38
- Caution 39
- Engineering settings 39
- Gearbox ratios 39
- Rotary 39
- Caution 40
- Engineering settings 40
- Jog speed 40
- Rotary speed 40
- Tray speed 40
- Wipe back default settings see 5a 40
- Gearbox ratio 41
- Hard dough 41
- Offset 41
- Wirecut 41
- Wirecut settings 41
- Wirecut speed acceleration 41
- Caution 42
- Do not attempt to make adjustments unless you are fully aware of the results 42
- Fault information screens 42
- Maintenance 44
- Warning do not under any circumstances use a water hose or pressure washer to clean this machine 44
- Check and maintenance schedule 45
- Mono omega touch 45
- Under no circumstances should maintenance or cleaning of this machine be done with the power connected 45
- Email spares monoequip com spares tel 44 0 1792 564039 web site www monoequip com main tel 01792 561234 fax 01792 561016 46
- Spares and service 46
- Uk service spares and overseas support 46
- Omega plus including wirecut version 47
- Spares 47
- Electrical component layout parts 48
- Mechanical component layout parts 49
- Omega plus wirecut version 49
- Rear view with cover removed 49
- Mechanical component layout parts 50
- Omega plus without wirecut 50
- Rear view with cover removed 50
- Electrical component layout parts 51
- Base machine spares list with wirecut 52
- Hard dough hopper parts 53
- Omega plus 53
- Omega plus 54
- Soft dough hopper parts 54
- Electrical information 55
- Queensway swansea west industrial estate swansea sa5 4eb uk tel 44 0 1792 561234 spares tel 44 0 1792 564039 fax 01792 561016 email marketing monoequip com 70
- The equipment mentioned in this manual has ce accreditation 70
- Web site www monoequip com 70
Похожие устройства
- Mono Epsilon 450 Инструкция по эксплуатации
- Mono Epsilon 450 Брошюра
- Mono Epsilon 400 Инструкция по эксплуатации
- Mono Epsilon 400 Брошюра
- Gemm ARG/41 Инструкция по эксплуатации
- Gemm ARG/41 Каталог оборудования Gemm
- Gemm ARG/40 Инструкция по эксплуатации
- Gemm ARG/40 Каталог оборудования Gemm
- Gemm TAL/16S Инструкция по эксплуатации
- Gemm TAL/16S Каталог оборудования Gemm
- Gemm TAL/16A Инструкция по эксплуатации
- Gemm TAL/16A Каталог оборудования Gemm
- Gemm TAL/27 Инструкция по эксплуатации
- Gemm TAL/27 Каталог оборудования Gemm
- Gemm TAL/27S Инструкция по эксплуатации
- Gemm TAL/27S Каталог оборудования Gemm
- Gemm TAL/21S Инструкция по эксплуатации
- Gemm TAL/21S Каталог оборудования Gemm
- Gemm TAL/27A Инструкция по эксплуатации
- Gemm TAL/27A Каталог оборудования Gemm