![Mono Omega Plus 400 (твердое тесто) [3/70] Failure to adhere to the cleaning and maintenance instructions detailed in this booklet could affect the warranty of this machine](/img/pdf.png)
Mono Omega Plus 400 (твердое тесто) [3/70] Failure to adhere to the cleaning and maintenance instructions detailed in this booklet could affect the warranty of this machine
![Mono Omega Plus 400 (твердое тесто) [3/70] Failure to adhere to the cleaning and maintenance instructions detailed in this booklet could affect the warranty of this machine](/views2/1334008/page3/bg3.png)
FG079 –OMEGA TOUCH INCL WIRECUT 09/12 RAC
3
Failure to adhere to the cleaning and
maintenance instructions detailed in this booklet
could affect the warranty of this machine.
Omega
PLUS
FOR SAFE WORKING, PAY SPECIAL ATTENTION TO ITEMS MARKED
WIRECUT VERSION
Содержание
- Depositor 400 450 1
- Manual 1
- Omega plus 1
- Operating and maintenance 1
- Failure to adhere to the cleaning and maintenance instructions detailed in this booklet could affect the warranty of this machine 3
- Contents 4
- Operating instructions 4
- Preparing for operation 4
- Introduction 5
- Dimensions 6
- Models are available with or without wirecut option 6
- Omega plus 6
- Specifications 7
- Safety 8
- All cleaning and maintenance operations must 9
- Be made with the machine disconnected from 9
- The power supply 9
- In an emergency switch off at the in an emergency switch off at the electrical mains wall isolator or push the emergency stop button 10
- Installation 10
- Isolation 10
- Stop button 10
- To release the emergency stop button turn clockwise 10
- Cleaning instructions 11
- Hard and soft dough hoppers 11
- Soft dough hopper 13
- Do not leave any components in the hopper 14
- Hard dough hopper 14
- Operating conditions 15
- Preparing for operation 16
- A fitting the hopper 17
- Do not operate machine without template fitted 17
- B fitting a template soft dough 18
- Do not operate machine without template fitted 18
- Before using straight offset nozzle holders 19
- O rings must be fitted 19
- Do not operate machine without template fitted 20
- Hard dough 20
- Fitting wirecut fingers 21
- If wirecut fitted 21
- If wirecut fitted 22
- Replacing broken wire 22
- Omega plus operation 23
- Change settings 24
- For following instructions 24
- If a grey box is shown in the button description e g go to the corresponding page further on in the instructions marked in top right hand corner of each page 24
- Operating key 24
- Operation 24
- Select product type 25
- Then to move to the next screen 25
- To create a new program 25
- Touch the screen for the type of product required 25
- Select saved product type 26
- To create new program 26
- Confirm setup of machine 27
- Machine is set as shown on the screen this screen controls the actions required by the operator 28
- Operator screen 28
- Program 28
- Start manual 28
- Start stop 28
- Drop with twist 29
- Edit and save screen 29
- Example drop with twist 29
- Save edits 29
- Example 30
- Multidrop with twist 30
- Other setting buttons are the same as last page 30
- Sheeting strip 30
- Example c shape arc 31
- Number of rows per 32
- Tray edge height mm 32
- Tray length mm 32
- Tray setup 32
- Delete 34
- Caution 35
- Diagnostics 35
- Do not attempt to make adjustments unless you are fully aware of the results 35
- Engineering settings 35
- Passwords 35
- Reset factory defaults 35
- Screen adjustment 35
- Caution 36
- Engineering settings 36
- Caution 37
- Engineering settings 37
- Caution 38
- Engineering settings 38
- Caution 39
- Engineering settings 39
- Gearbox ratios 39
- Rotary 39
- Caution 40
- Engineering settings 40
- Jog speed 40
- Rotary speed 40
- Tray speed 40
- Wipe back default settings see 5a 40
- Gearbox ratio 41
- Hard dough 41
- Offset 41
- Wirecut 41
- Wirecut settings 41
- Wirecut speed acceleration 41
- Caution 42
- Do not attempt to make adjustments unless you are fully aware of the results 42
- Fault information screens 42
- Maintenance 44
- Warning do not under any circumstances use a water hose or pressure washer to clean this machine 44
- Check and maintenance schedule 45
- Mono omega touch 45
- Under no circumstances should maintenance or cleaning of this machine be done with the power connected 45
- Email spares monoequip com spares tel 44 0 1792 564039 web site www monoequip com main tel 01792 561234 fax 01792 561016 46
- Spares and service 46
- Uk service spares and overseas support 46
- Omega plus including wirecut version 47
- Spares 47
- Electrical component layout parts 48
- Mechanical component layout parts 49
- Omega plus wirecut version 49
- Rear view with cover removed 49
- Mechanical component layout parts 50
- Omega plus without wirecut 50
- Rear view with cover removed 50
- Electrical component layout parts 51
- Base machine spares list with wirecut 52
- Hard dough hopper parts 53
- Omega plus 53
- Omega plus 54
- Soft dough hopper parts 54
- Electrical information 55
- Queensway swansea west industrial estate swansea sa5 4eb uk tel 44 0 1792 561234 spares tel 44 0 1792 564039 fax 01792 561016 email marketing monoequip com 70
- The equipment mentioned in this manual has ce accreditation 70
- Web site www monoequip com 70
Похожие устройства
- Mono Epsilon 450 Инструкция по эксплуатации
- Mono Epsilon 450 Брошюра
- Mono Epsilon 400 Инструкция по эксплуатации
- Mono Epsilon 400 Брошюра
- Gemm ARG/41 Инструкция по эксплуатации
- Gemm ARG/41 Каталог оборудования Gemm
- Gemm ARG/40 Инструкция по эксплуатации
- Gemm ARG/40 Каталог оборудования Gemm
- Gemm TAL/16S Инструкция по эксплуатации
- Gemm TAL/16S Каталог оборудования Gemm
- Gemm TAL/16A Инструкция по эксплуатации
- Gemm TAL/16A Каталог оборудования Gemm
- Gemm TAL/27 Инструкция по эксплуатации
- Gemm TAL/27 Каталог оборудования Gemm
- Gemm TAL/27S Инструкция по эксплуатации
- Gemm TAL/27S Каталог оборудования Gemm
- Gemm TAL/21S Инструкция по эксплуатации
- Gemm TAL/21S Каталог оборудования Gemm
- Gemm TAL/27A Инструкция по эксплуатации
- Gemm TAL/27A Каталог оборудования Gemm