MCZ Forma 75 dx [37/40] Maintenance and cleaning
![MCZ Forma 75 dx [37/40] Maintenance and cleaning](/views2/1336206/page37/bg25.png)
35
8-MAINTENANCE AND CLEANING
Technical Dept. - All rights reserved - Reproduction is prohibited
CLEANING THE ASH
One recommends adequate cleaning of the hearth for proper combustion. To remove the ash from the hearth use a metal scoop and brush
and store the ash in non-ammable containers for transport.
Hot ashes must not be stored outside unsupervised or thrown into the rubbish bin. Allow it to cool in the open air in a
metal container.
CLEANING THE REFRACTORY PARTS (ALUTEC®)
They do not require any cleaning as the characteristic of this material (ALUTEC®) is that it does not absorb soot but instead it repels it when
the replace is hot. After the start-up stage in which the replace tends to tarnish, the refractory parts will turn white again, starting from
the base of the ame, when the combustion chamber reaches working temperature (~ 400° C).
If this phenomena does not take place it may be caused by:
• Damp or resinous wood that does not emit sucient heat or that dirties the combustion chamber
• Chimney with poor performance and therefore smoke stays in the combustion chamber for too long, dirtying the rebox
• Chimney with low performance that does not allow the closed replace to reach high eciency and therefore adequate temperatures
for the refractory parts.
Never clean the refractory parts with a damp cloth or other as it could get stained.
If required use a dry paintbrush to remove thick accumulations of soot.
Should the Alutec not whiten, it must not be considered as a defect in light of the warnings and indications reported
above.
CLEANING PERFORMED BY A QUALIFIED TECHNICIAN
CLEANING THE CHIMNEY
We recommend the mechanical cleaning of the ue pipe at least once a year; excess build-up of unburned waste could cause problems
with the smoke outlet pipe and start a re in the ue pipe itself. To clean the chimney ue by accessing from the appliance, remove the
smoke deector: to remove it properly lift it from the front part and make it simultaneously come forwards to free it from the resting
supports at the back.
Содержание
- Care of the manual and how to consult it 3
- Introduction 3
- Revisions to the publication 3
- Symbols used in the manual 3
- Safety precautions 4
- Warnings and warranty conditions 4
- Information 5
- Intended use 5
- Warnings and warranty conditions 5
- Warranty conditions 5
- Exclusions 6
- Warnings and warranty conditions 6
- Spare parts 7
- Warnings and warranty conditions 7
- Warnings for the correct disposal of the product 7
- Installation 9
- Installation foreword 9
- Minimum distances 9
- Foreword 10
- Min 5 metri 10
- Smoke flue 10
- Technical characteristics 11
- Dimensioning 12
- Chimney 13
- Chimney components 13
- Maintenance 13
- External air inlet 14
- Connection to flue 15
- Examples of correct installation 17
- Dimensions and technical characteristics 18
- Forma wood 75 dx sx dimensions sx left version in figure 18
- Dimensions and technical characteristics 19
- Forma wood 95 dx sx dimensions sx left version in figure 19
- Technical dept all rights reserved reproduction is prohibited 19
- Dimensions and technical characteristics 20
- Forma wood t95 dimensions 20
- Dimensions and technical characteristics 21
- Forma wood t50 dimensions 21
- Technical dept all rights reserved reproduction is prohibited 21
- Dimensions and technical characteristics 22
- Technical characteristics 22
- Installation and assembly 23
- Preparation and unpacking 23
- Choice of operating mode 24
- Counterweights unlocking 24
- Forced convection comfort air vf 24
- Installation and assembly 24
- Natural convection comfort air vn 24
- Installation and assembly 25
- Positioning 25
- Height and level adjustment 26
- Installation and assembly 26
- Combustion air inlet 27
- External and internal air inlet 27
- Forced ventilation air inlet 27
- Installation and assembly 27
- Natural ventilation air inlet 27
- Cladding and counter hood assembly 28
- Flue connection 28
- Installation and assembly 28
- Fireplace insulation 29
- Hood ventilation outlets 29
- Installation and assembly 29
- Wooden beam insulation 29
- Do not expect heating efficiency immediately 30
- Operation 30
- Operation test 30
- Start up precautions 30
- Fuel wood 31
- Operation 31
- Stages for the first start up test 31
- First ignition 32
- Operation 32
- Fuel loading 33
- Operation 33
- Combustion control 34
- Operation 34
- Primary air 34
- Door opening switch 35
- Operation 35
- Quick response 35
- Secondary air 35
- Cleaning performed by the user 36
- Cleaning the glass 36
- Maintenance and cleaning 36
- Cleaning performed by a qualified technician 37
- Cleaning the ash 37
- Cleaning the chimney 37
- Cleaning the refractory parts alutec 37
- Maintenance and cleaning 37
Похожие устройства
- MCZ Forma 75 dx Сертификат
- MCZ Forma T95 Инструкция по эксплуатации
- MCZ Forma T95 Сертификат
- MCZ Forma 75 Инструкция по эксплуатации
- MCZ Forma 75 Сертификат
- MCZ Forma T50 Инструкция по эксплуатации
- MCZ Forma T50 Сертификат
- CAS ER JR-15CB LT черные Инструкция по эксплуатации
- CAS ER JR-15CB черные Инструкция по эксплуатации
- MCZ HydroTherm 70 dx Инструкция по эксплуатации
- MCZ HydroTherm 70 dx Сертификат
- CAS ER JR-30CB LT черные Инструкция по эксплуатации
- MCZ HydroTherm E80 Инструкция по эксплуатации
- MCZ HydroTherm E80 Сертификат
- MCZ HydroTherm 70V Инструкция по эксплуатации
- MCZ HydroTherm 70V Сертификат
- CAS ER JR-15CBU черные Инструкция по эксплуатации
- MCZ HydroTherm 80 Инструкция по эксплуатации
- MCZ HydroTherm 80 Сертификат
- CAS ER JR-30CB черные Инструкция по эксплуатации