Dremel 4000 6/128 F0134000LR [19/44] Warning
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Dremel 4000 6/128 F0134000LR [19/44] Warning

Dremel 4000 6/128 F0134000LR [19/44] Warning
side forces applied to these wheels may cause them to
shatter.
 


Proper mandrels will reduce the possibility of breakage.
 Do not “jam” a cut-off wheel or apply excessive

Overstressing the wheel increases the loading and
susceptibility to twisting or snagging of the wheel in the cut
and the possibility of kickback or wheel breakage.
 Do not position your hand in line with and behind the
When the wheel, at the point of operation,
is moving away from your hand, the possible kickback may
propel the spinning wheel and the power tool directly at
you.
 
a cut for any reason, switch off the power tool and
hold the power tool motionless until the wheel comes
Never attempt to remove the cut-off
wheel from the cut while the wheel is in motion otherwise
kickback may occur. Investigate and take corrective action
to eliminate the cause of wheel pinching or snagging.
 
Let the wheel reach full speed and carefully re-enter the
The wheel may bind, walk up or kickback if the power
tool is restarted in the workpiece.
 Support panels or any oversized workpiece to minimize
Large
workpieces tend to sag under their own weight. Supports
must be placed under the workpiece near the line of cut
and near the edge of the workpiece on both sides of the
wheel.
 
The protruding wheel
may cut gas or water pipes, electrical wiring or objects that
can cause kickback.
SAFETY WARNINGS SPECIFIC FOR WIRE BRUSHING
OPERATIONS
 Be aware that wire bristles are thrown by the brush

The wire
bristles can easily penetrate light clothing and/or skin.
 

Loose bristles or
wires will be discharged during the run-in time.
 
Small particles and tiny wire fragments may be
discharged at high velocity during the use of these brushes
and may become imbedded in your skin.
 
!
WARNING
DO NOT WORK WITH MATERIALS
CONTAINING ASBESTOS (ASBESTOS IS

!
WARNING
TAKE PROTECTIVE MEASURES WHEN
DURING WORK DUST CAN DEVELOP

COMBUSTIBLE OR EXPLOSIVE (SOME DUSTS ARE


ENVIRONMENT
DISPOSAL
The machine, accessories and packaging should be sorted for
environmental-friendly recycling.
ONLY FOR EC COUNTRIES
Do not dispose of power tools with household waste!
According the European Guideline 2012/19/EC for
Waste Electrical and Electronic Equipment and its
implementation into national law, power tools that are
no longer usable must be collected separately and
disposed of in an environmentally-correct manner.
SPECIFICATIONS
GENERAL SPECIFICATIONS
200 3000 4000 4200
Rated Power (W) 125 130 175 175
Voltage Rating
230-240 V,
50 Hz
230 V,
50 Hz
230-240 V,
50-60 Hz
220-240 V,
50-60 Hz
Collet Capacity 0.8 mm, 1.6 mm, 2.4 mm, 3.2 mm
Rated Speed (n) 35,000
RPM
33,000
RPM
35,000
RPM
33,000
RPM
Class II
Construction
Double insulated construction tools
EXTENSION CORDS
Use completely unrolled and safe extension cords with a
capacity of 5 Amps.
MOTOR SPECIFICATIONS
Only 3000
This multitool utilizes a variable high speed motor. It is wired
for operation on 230 V, 50 Hz. Always check that the supply
voltage is the same as the voltage indicated on the nameplate
of the tool.
ASSEMBLY
ALWAYS UNPLUG MULTITOOL BEFORE CHANGING
ACCESSORIES, CHANGING COLLETS, OR SERVICING THE
TOOL.
GENERAL
The Dremel multitool is a high quality precision tool that can be
used to perform detailed and intricate tasks. The wide range
of Dremel accessories and attachments allow you to perform
a large variety of tasks. These include tasks such as sanding,
carving, engraving, routing, cleaning and polishing.
PICTURE: 2-5
A. Collet nut
B. Collet
C. Housing cap or EZ
Twist™ integrated
wrench/nose cap
D. Shaft lock button
E. On/Off switch
F. Hanger
G. Power cord
H. Brush cover
I. Ventilation openings
J. Variable speed dial
K. Collet wrench
EZ information
Only 4200
L. EZ Change levers
M. EZ Change chuck
19

Содержание

Похожие устройства

Скачать