![Tantos TSc-SD960HWZ18 (5-90) [4/26] Installation instruction](/img/pdf.png)
Tantos TSc-SD960HWZ18 (5-90) [4/26] Installation instruction
![Tantos TSc-SD960HWZ18 (5-90) [4/26] Installation instruction](/views2/1372403/page4/bg4.png)
3
4
Installation Instruction
Installation Instruction
1. 1. 2 Dome-Insert Installation conditions:
Insert dome camera is applied to indoor ceiling setting
(1) At least 200mm above the ceiling
(2) ceiling thickness is 5mm—42mm
(3) ceiling must bear 4 times the weight of camera at least.
Step a. Drill a hole in the ceiling
(1) Use proper tools to drill a hole with 3mm diameter in the center of
installation place.On one side of the hole twist a self-drilling screw and
fix it on the ceiling.
(2)Draw a circle with pencil in ceiling, and then remove the material
inside the circuit.
Step c. Set speed dome ID & Baudrate &Protocol
(1) Set (DIP switches) SW1/SW2 under the bottom of dome machine to
control speed dome.
(Detailed information can be found in A )ppendix
(2) Without DIP switches , setting the ID address by software address
refer to OSD MEUN
Step b. Install ceiling mount
(1) First, keep pushing the ceiling mount into the hole in the ceiling until
the mount is totally inside the hole. Second, unfold the three brackets and
screw them up.
Last, when the metal pieces are fully expanded, tighten the screws to fix
the mount into ceiling firmly.
Warning: A steel safe belt must be used between ceilingmount and ceiling
to avoid that speed dome accidentally drops. Safe belt should be provided
by user .
1.1.3.Ceiling-mounted installation
Installation conditions:
This installation way is applied to stiff ceiling indoor
(1) The thickness of ceiling must be enough to set up the screws
(2) Ceiling must bear 4 times the weight of camera
Step a. drill a hole in the ceiling
(1) Draw a circle according to the size of hole witha pencil in ceiling,
and then remove the material inside the circuit.
(2) Drill three holes around the hole in the ceiling according to the
corresponding position in the mount and insert setscrews in each hole.
(Setscrews should be provided by users).
pro tocol
baudrate
120R
Step d. Connect dome lines
⑴Put video line, power supply line and signal controlline through the
round hole in the ceiling mount, and connect the lines with the corresponding
places in dome.
Steps e. Dome installation
⑴Insert the three screws which are in the bottom of dome into the holes in
ceiling mount, and then turn the mount as figure 5 shows to make sure that
the screws are inside positioning slot firmly.
Step b. fix ceiling mount
There are two connection ways:
One is from center hole, the other is from the hole beside
⑴ Make sure the installation position and the connection way.
Insert the three setscrews in the holes respectively, and then fasten
the screws with gasket and screw cap.(Take the example of putting the
wire through the center of ceiling mount)
Step c. Set speed dome ID & Baudrate &Protocol
(Refer to page 3 - ) Picture 1.2-1
Picture 1.2-1
Picture 1.2-2
Picture 1.2-3
Picture 1.2-1
Picture 1.2-4
Picture 1.3-1
Picture 1.3-2
Picture 1.3-3
Picture 1.3-4
Содержание
- Table of content 2
- Installation instruction 3
- Precaution 3
- 2 dome insert installation conditions 4
- Ceiling mounted installation 4
- Installation instruction 4
- Refer to page 3 4
- Step c set speed dome id baudrate protocol 4
- Installation instruction 5
- Camera parameter 6
- Performance 6
- Physical 6
- Technology parameter 6
- All the menu option are displayed in english 7
- Built in digital camera 7
- Built in direction indicator and temperature indicator 7
- Built in pan tilt 7
- Camera rotates tilts up to 90 degrees you may directly watch the rear view to realize surveillance all pr ocesses in portrait 180 degrees in the menu you may set the system parameter setting auto flip as on thus you may run this function 7
- Exquisite mechanical drive support pan 360 continuously and tilt 0 90 and may rotate180 7
- Figure design all the data are stored in the inner of camera pan tilt when power off the storage data can t be lose built in decoder integrated multi protocol including pelco d pelco p factory etc 7
- Focus control 7
- Focus speed proportion pan 7
- Function instruction 7
- If user holds the joystick in the down position the camera rotates pan 180 degrees he then t 7
- Integrated and multi protocol decoder 7
- Internal temperature test 7
- Iron and carbon alloy structure high intensity and good heat dissipation 7
- Keyboard and menu display may set park action and set power up action or carry out appointed action 7
- Magnification contro 7
- Os d menu 7
- Park action 7
- Pattern 4 scan 4tour 7
- Performance 7
- Power up action 7
- Precise stepping motor rotate smoothly react sensitivity and orientate accurately 7
- Presets can be stored preset 1 80 support auto tour and each tour can store up to 32 presets 7
- Rs485 bus controlling in series and dome id 1 255 optional 7
- This passage mainly describes the main function and general principle of mini speed dome and does not refer to the operation methods 7
- This product is high technology surveillance product with high definition and color camera variable speed pan tilt and multifunction decoder it can reduce the connection and installation process between systematic parts at a max limit and also can improve the stability and reliability of the system meanwhile it is easy to install and repair and it has the following advantages beau tiful shape rotate lightly and neatly little noise simple operation and so on 7
- Video osd menu it is direct and simple to revise the dome information and parameter by 7
- When the temperature exceeds the upper limit the screen will display alarm information according to the real time temperature the fan will measure if it starts or not and prolong the life of fan 7
- With auto flip rotate slowly at pan 1 s and the image doesn t jitter 7
- Auto back light compensation 8
- Auto white balance 8
- Basic operation 8
- Camera can automatically adjust white balance in accordance with the alteration of background light ness to reach a true colour 8
- Camera sub area can carry out auto back light compensation under a strong light background camera will auto compensate light for the darker object and adjust daylight to the bright background in order to avoid making the image lack fidelity by the back line is too bright and the object is unable to recognize because of darkness thus gain legible image 8
- Inner temperature sensor surveille temperature inside of the dome when the dome work in the high temperature the dome will automatically to start up the fan to reduce the heat to make sure the dome work in the reliable temperature environment increase its stability and prolong the life time of the dome 8
- Iris control 8
- Keyboard operation 8
- Monitor function 8
- Need user also can resume auto iris by joystick operation when controlling the iris manually the dome locks current position you manually controlled when operating joystick the dome resume auto iris 8
- System defaults auto iris camera can rapidly adjust size of iris through the automatically induct the changing of environment ray and thus make the brightness of deferent image stable user may adjust iris by controlling keyboard to get required brightness that you open close 8
- System setting 8
- Dome initial information 9
- Edit dome title 9
- System setting 9
- Dome id setting 10
- Password setup 10
- System setting 10
- 1 power up action 11
- Clock setting 11
- Date set year month date 11
- Day set week 11
- System parameter 11
- System setting 11
- Time set hour minute second 11
- 2 pan tilt setting 12
- 3 time action setup 12
- 4 park action setup 12
- System setting 12
- Camera setting 13
- Defaults 13
- Lens parameters 13
- System setting 13
- 3 back light compensation 14
- 4 slow shutter control 14
- Camera setting 14
- 5 wdr control 15
- 6 day night setting 15
- Camera setting 15
- Ae mode 16
- Camera setting 16
- White balance mode 16
- Advance parameters 17
- Camera setting 17
- Privacy zone masking 17
- Function setting 18
- Preset 18
- Function setting 19
- Pattern 19
- Display setup 20
- Function setting 20
- Ae mode auto shutter n a iris n a bright n a back exit 21
- Appendix 21
- Back exit 21
- Camera setting 21
- Display setup 21
- Dome id setting 21
- Dome s n version model protocol factory dome id 001 baud rate 4800bps back exit 21
- Edit dome 21
- Function setting 21
- Infrared setting 21
- Lens parameters high ae mode setting on awb mode setting off advance parameters privacy mask back exit 21
- Main menu 21
- Pattern number 1 record pattern run pattern clear pattern edit pattern title back exit 21
- Patterns 21
- Preset number 001 set preset show preset clear current preset edit preset title back exit 21
- Presets 21
- Privacy number 01 edit privacy enable privacy off clear privacy back exit 21
- Scan number 1 scan speed 20 set left limit set right limit clear scan run scan edit scan title back exit 21
- Sharpness 05 hi resolution on max gain 28db expos comp n a back exit 21
- System setting 21
- System setting camera setting function setting display setup exit 21
- Title pattern 1 back exit 21
- Title pre001 back exit 21
- Title scan 1 back exit 21
- Zone number 1 set left limit set right limit clear zone edit zone title back exit 21
- Zoom speed high digital zoom off blc mode off slow shutter off wdr mode n a mirror off flip off day night settin 21
- Appendix 22
- As specified by rs485 standard rs485 bus is of half duplexed data transmission cables with characteristic impedance as 120 ω the maximum load capacity is 32unit loads including main controller and controller equipment 22
- Be caution when cleaning hold the down cover ring only to avoid direct touch to the acrylic down cover the acid sweat mark of fingerprint will corrode the coating of down cover and scratch on down cover will cause vague image 22
- Bps 4800bps 9600bps 22
- Bps 600m 22
- For hand contamination use neutral detergent any cleanser for high grade furniture is applicable 22
- If user selects thinner cables or installs the dome in an environment with strong electroma gnetic interference or connects lots of equipment to the rs485bus the max transmitting distance will be decreased to increase the maximum transmitting distance do the contrary 22
- In some circumstances user adopts a star configuration in practical connection the termination resistors must be connected to the two equipment 1 and 15 in picture 9 3 as the star configuration is not in conformity with the requirements of rs485 standards problems such as signal reflec tions lower anti interference performance arise when the cables are long in the conn ection the reliability of control signals is decreased with the phenomena that the dome does not respond or just responds at intervals to the controller or does continuous operation without stop 22
- M 1200m 800m 22
- Rs485bus basic knowledge 22
- The cleaning of clear down cover 22
- The rs485bus standards require a daisy chain connection between the equipment there must be termination resistors with 120 ω as the picture 9 1 please refer to picture 9 2 for simple connection d should not exceed 7m 22
- To obtain constant clear videos user should clean the down cover periodically 22
- Trouble shooting 22
- Use soft dry cloth or the substitute to clean the inner and outer surfaces 22
- When user selects the 0 6mm 24awg twist pair wires as data transmission cable the max theoretical transmitting distance are as follows 22
- 1 baud rate setup sw2 23
- 2 protocol setup sw2 23
- 3 id setting sw1 23
- And set dip as off 0 23
- Appendix 23
- Basic knowledge to check whether baud rate 23
- Board of the dome see picture 9 3 sw1 is 23
- Chage the address and baud rate of contro ller or dome 2 adjust the and connection of rs485 3 make sure the connections are fully seated 4 change rs485 bus wires 23
- Connect or disconnect the 120 ω termination resistor by adjusting the eighth bit of the sw2 on the main board 1 set as on means connect and set disconnect 0 as off means 23
- Diamond 23
- Dip switch setup 23
- Distance in the following list 1 set dip as on 23
- Dome can do self testing but can not be controlled 23
- Factory 23
- For dome address setting and sw2 is for dome 23
- In a system a decoder includes speed dome camera and common decoder there aren t the 23
- Is satisfied with the demand of transmission 23
- Picture 9 5 23
- Please according to appdienx rs485 bus 23
- Protocol 23
- Protocol and baud rate setting 23
- Same id between them the id switch in decoder and the id setting of the dome as follow in the 23
- Sheet 1 set dip switch as no 0 set dip switch as off 23
- Solution 23
- Sw2 sw1 23
- The address and baud rate setting of dome are not in conformity with those of controller 2 the and connection of rs485 bus is incorrect 3 bad connection 4 there are circuit in the rs485 bus 23
- The connection of 120 ω termination resistor 23
- The dome can be controlled but the opera tion is not smooth 23
- The rs485bus is not in good contact with the connectors 2 one wire of rs485bus is broken 3 the dome is very far from controller 4 there are two many domes connected in the system 23
- There are two dip switches on the main 23
- 0 0 0 0 0 0 1 24
- 0 0 0 0 1 1 0 24
- 0 0 0 1 0 1 0 24
- 0 0 0 1 1 1 0 24
- 0 0 1 0 0 1 0 24
- 0 0 1 0 1 1 0 24
- 0 0 1 1 0 1 0 24
- 0 0 1 1 1 1 0 24
- 0 1 0 0 0 1 0 24
- 0 1 0 0 1 1 0 24
- 0 1 0 1 0 1 0 24
- 0 1 0 1 1 1 0 24
- 0 1 1 0 0 1 0 24
- 0 1 1 0 1 1 0 24
- 0 1 1 1 0 1 0 24
- 0 1 1 1 1 1 0 24
- 1 0 0 0 0 0 1 24
- 1 0 0 0 1 1 0 24
- 1 0 0 1 0 1 0 24
- 1 0 0 1 1 1 0 24
- 1 0 1 0 0 1 0 24
- 1 0 1 0 1 1 0 24
- 1 0 1 1 0 1 0 24
- 1 0 1 1 1 1 0 24
- 1 1 0 0 0 1 0 24
- 1 1 0 0 1 1 0 24
- 1 1 0 1 0 1 0 24
- 1 1 0 1 1 1 0 24
- 1 1 1 0 0 1 0 24
- 1 1 1 0 1 0 0 24
- 1 1 1 0 1 1 0 24
- 1 1 1 1 0 1 0 24
- 1 1 1 1 1 1 0 24
- Appendix 24
- Id 1 2 3 4 5 6 7 8 24
- Sw1 sw1 24
- 0 0 0 0 1 1 1 25
- 0 0 0 1 0 1 1 25
- 0 0 0 1 1 1 1 25
- 0 0 1 0 0 1 1 25
- 0 0 1 0 1 1 1 25
- 0 0 1 1 0 1 1 25
- 0 0 1 1 1 1 1 25
- 0 1 0 0 1 1 1 25
- 0 1 0 1 0 1 1 25
- 0 1 0 1 1 1 1 25
- 0 1 1 0 0 1 1 25
- 0 1 1 0 1 1 1 25
- 0 1 1 1 0 1 1 25
- 0 1 1 1 1 1 1 25
- 1 0 0 0 1 1 1 25
- 1 0 0 1 0 1 1 25
- 1 0 0 1 1 1 1 25
- 1 0 1 0 1 1 1 25
- 1 0 1 1 0 1 1 25
- 1 0 1 1 1 1 1 25
- 1 1 0 0 1 1 1 25
- 1 1 0 1 0 1 1 25
- 1 1 0 1 1 1 1 25
- 1 1 1 0 0 1 1 25
- 1 1 1 0 1 1 1 25
- 1 1 1 1 0 1 1 25
- 1 1 1 1 1 1 1 25
- 2 3 4 5 6 7 8 25
- Address is set as 0 user can select any protocols 25
- Appendix 25
- Broadcast address only factory 25
- Cameras will carry our the same motions 25
- Debug address only factory 25
- Notice 25
- Protocol and pelco can be set if the camera 25
- Protocol and pelco can be set if user selects 25
- Switch number 25
- To control all the systematic connection 25
- To control the dome 25
- 1 range of warranty 26
- 2 warranty terms 26
- 3 shipping 26
- Maintenance 26
- Shortcut key 26
Похожие устройства
- Tantos TSc-SD960HWZ18 (5-90) Руководство по настройке
- Tantos TSc-SD960HZ10 (5.5-55) Инструкция по эксплуатации
- Tantos TSc-SD960HZ10 (5.5-55) Руководство по настройке
- Tantos TSc-SDi1080FHD(x10) Инструкция по эксплуатации
- Tantos TSc-SDW1080pZ10IR Инструкция по эксплуатации
- Tantos TSc-SDW1080pZ10IR Руководство по подключению
- Tantos TSc-SDW1080pZ18IR Инструкция по эксплуатации
- Tantos TSc-SDW960pZ10IR Инструкция по эксплуатации
- Tantos TSr-AV0411 Light Инструкция по эксплуатации
- Tantos TSr-AV0411 Light Руководство по настройке
- Tantos TSr-AV0411 Light Руководство по подключению
- Tantos TSr-AV0411 Standard Инструкция по эксплуатации
- Tantos TSr-AV0411 Standard Руководство по подключению
- Tantos TSr-AV0411 Standard Инструкция по настройке RTSP потока
- Tantos TSr-AV0811 Standard Инструкция по эксплуатации
- Tantos TSr-AV0811 Standard Руководство по подключению
- Tantos TSr-AV0811 Standard Инструкция по настройке RTSP потока
- Tantos TSr-AV1621 Standard Инструкция по эксплуатации
- Tantos TSr-AV1621 Standard Руководство по подключению
- Tantos TSr-AV1621 Standard Инструкция по настройке RTSP потока