![Fluke 707 [3/16] Press in and tur](/img/pdf.png)
Fluke 707 [3/16] Press in and tur
![Fluke 707 [3/16] Press in and tur](/views2/1005445/page3/bg3.png)
English Instruction SheetPanel 3
Pushbutton Functions
Pushbutton Function
D
ON or OFF button.
A
+ D
(Power-on Option)
Press A and D simultaneously to toggle
between the mA output spans.
• 4 mA to 20 mA = 0 % - 100 % (default)
• 0 mA to 20 mA = 0 % - 100 % (optional)
The selection is saved until it is changed.
l+ D
(Power-on Option)
Press l + D simultaneously to turn HART
resistor (Hr) on. Default is off.
A
Press to step through modes:
• Source mA
• Simulate mA
• Measure mA
• Loop Power (24 V)
• Measure V dc
h i j
Turn n to increase or decrease current output.
Current output can be adjusted at a resolution of
1 μA or 100 μA. (Default is 1 μA.)
• To adjust the current in 1 μA steps, simply
turn the knob.
• To adjust the current in 100 μA steps,
press
in and turn the knob.
B
Press
B
to step the current up 25 % of full
scale (20 mA).
At full scale, press
B
to step the current down
25 % of full scale.
B+ C
Press B + C simultaneously to enter the
Auto Ramp mode and select a ramp form.
A continuously applied or controlled mA ramping
signal is produced in one of three ramp forms.
e (slow), g (fast), or f (step) identifies the
selected ramp form.
C
Press C to start the SpanCheck™ at 0 % of
selected current span, i.e., 0 mA for 0-20 mA span
or 4 mA for 4-20 mA span.
d
is displayed.
Press again for 100 % of selected current span.
Содержание
- Battery saver 1
- Instruction sheet 1
- Introduction 1
- Loop calibrator 1
- English instruction sheetpanel 2 2
- Symbols 2
- W warnings and cautions 2
- Press in and tur 3
- Changing the ma output span 4
- English instruction sheetpanel 4 4
- Sourcing ma 4
- Using the ma sourcing output modes 4
- Contacting fluke 5
- English instruction sheetpanel 5 5
- A 12 v to 28 v loop supply must be available insert the test leads as shown below 6
- English instruction sheetpanel 6 6
- Simulating a transmitter 6
- When simulating the operation of a transmitter the calibrator regulates the loop current to a known value selected by you 6
- Auto ramping the ma output 7
- English instruction sheetpanel 7 7
- Using the spancheck function 7
- English instruction sheetpanel 8 8
- Measuring dc ma 8
- English instruction sheetpanel 9 9
- Measuring dc ma with loop power 9
- English instruction sheetpanel 10 10
- Measuring dc volts 10
- English instruction sheetpanel 11 11
- For maintenance procedures not described in this instruction sheet contact a fluke service center 11
- Maintenance 11
- W warning 11
- Calibration 12
- Cleaning 12
- English instruction sheetpanel 12 12
- In case of difficulty 12
- English instruction sheetpanel 13 13
- Hart mode 13
- Replacing the battery 13
- W warning 13
- English instruction sheetpanel 14 14
- Replaceable parts 14
- Accuracy specifications 15
- English instruction sheetpanel 15 15
- English instruction sheetpanel 16 16
- General specifications 16
Похожие устройства
- LG MH-6646QMS Инструкция по эксплуатации
- Supra SNP-433 Инструкция по эксплуатации
- Digitech XMM METAL MASTER Инструкция по эксплуатации
- Hotpoint-Ariston ARSD 129 Инструкция по эксплуатации
- Ada 5D Crosspoint Set А00192 Инструкция по эксплуатации
- Fluke 707 ex Инструкция по эксплуатации
- Supra SNP-431 Инструкция по эксплуатации
- Digitech BNX3 Инструкция по эксплуатации
- LG MH-6646QMB Инструкция по эксплуатации
- Hotpoint-Ariston ARUSL 105 Инструкция по эксплуатации
- Geo-Fennel FL 200 A-N 291000 Инструкция по эксплуатации
- Fluke 712 Инструкция по эксплуатации
- Digitech BP 200 Инструкция по эксплуатации
- Supra SNB-200 Инструкция по эксплуатации
- LG MH-6646QM Инструкция по эксплуатации
- Hotpoint-Ariston ARSL 105 (CSI).L Инструкция по эксплуатации
- Geo-Fennel FL 55 Multilinner 500050 Инструкция по эксплуатации
- Fluke 714 Инструкция по эксплуатации
- Digitech GNX2 Инструкция по эксплуатации
- Supra SNP-351 Инструкция по эксплуатации
Скачать
Случайные обсуждения