Home
Главная
Gorenje
Стиральная Машина
WTD 63111
Инструкция по эксплуатации Страница: 10

Gorenje WTD 63111 [10/35] Programming a drying cycle only

4 / PROGRAMMING YOUR APPLIANCE

• PROGRAMMING A WASH CYCLE (continued)

You can delay your cycle by pressing the delayed Start but-

tons (refer to the chapter on “OTHER FUNCTIONS”

“Delayed Start ”).

The display then shows the time before the cycle starts.

(When under one hour, the time is displayed in minutes).

•Operations to perform (continued)

Display

min

— Turn the program selector to the “0” position.

NB : Cancellation means you always have to re-program

from scratch.

If you have cancelled during washing, if you need to drain

the water, run a “Spin” program and set a suitable

speed.

All displays are extinguished

•Cancellation during programming, washing or

during pause

NB : After the spin, your washing machine automatically

cools the laundry and positions the drum with the opening

at the top for easier access to the laundry. This operation

lasts 3 minutes maximum.

The display then shows “StOP”, which tells you the

cycle has finished.

— Turn the program selector to the “0” position You can

then open the lid and remove your laundry.

•Indication of End of cycle

Important :

Before switching your machine on, check that the electrical power cord is connected and

the water valve is open. Ensure that the drum doors and the machine lid are properly closed.

In the "End of cycle" phase, when ”StOP” is displayed, any action on one of the control elements

(selector or buttons) lets you return to "Programming" mode.

For safety reasons, at the end of a cycle, we recommend disconnecting the power cord and shut-

ting off the water supply valve.

(The indicator lights flash alternately)

• PROGRAMMING A WASH CYCLE WITH SUBSEQUENT DRYING

• PROGRAMMING A DRYING CYCLE ONLY

Important :

To ensure proper drying, the load must not

exceed 4 kg.

If the machine estimates that the load is too large to permit

subsequent drying, it stops at the end of the wash cycle and

informs you via the figure “4” flashing on the display .

In this case, adjust the laundry load, and press the

“Start/Pause” button to resume drying.

•Operations to be perform

Display

The "Drying" indicator lights up.

•Operations to be perform

(The indicator for the

"Drying" option lights up)

The time displayed includes estima-

ted drying time.

Tr/min

Tip: To estimate the drying time, begin to choose a duration by default more than excess,

in order to avoid an over-drying of your laundry.

— Choose immediate start by pressing the “Start/Pause”

button ...

The cycle sequence indicator lights up.

The program begins.

Important : At the end of the drying cycle, remember to clean the drying filter

(refer to the

chapter on "EVERYDAY MAINTENANCE OF YOUR APPLIANCE").

Throughout the cycle, the machine

indicates the current phase of the

cycle...

... as well as the estimated time

remaining until the end of the cycle.

Your appliance lets you run a drying cycle straight after a

washing cycle with automatic detection of the end of

drying. This option always uses HIGH drying temperature.

NB: Results obtained may vary somewhat depending on the

type of laundry load.

To do this:

— Program your wash cycle (see previous pages).

— Sélect the “Drying” option using button “Drying” .

— Press the “Start/Pause” button . The cycle start.

NB: First ensure :

- that the water valve is open.

- that the load has been sufficiently spun (at least 1000 rpm)

and that it does not exceed half a drum.

— Turn the program selector to choose your “High”

or “Low” drying program according to the type of laun-

dry.

— Select a drying time using the button

Gorenje WTD 63111 [10/35] Programming a drying cycle only

Содержание

Похожие устройства