Home
Главная
Binatone
Утюг
SI-4024
Инструкция по эксплуатации Страница: 7

Binatone SI-4024 [7/38] Auto shut off function for si 4022

ENGLISH

Attention: Application of the steam ironing function is

impossible at «•» temperature setting. The «Drip

Stop» system automatically terminates the steam

generation process if the selected temperature is too

low. When the system is activated, you may hear a

light click.

Turbo steam

To ease ironing of dense cotton, linen and upholstery articles

use the steam burst button (8): engagement of the button (8)

during the ironing process generates an extra burst of steam from

the sole plate to help remove stubborn creases.

Burst of steam in a vertical position

This function helps to freshen the appearance of curtains, jack-

ets, coats, etc. To use this function, take the following steps:

! Follow instructions in paragraph 1-4 of the section «Operation

instructions». While selecting the temperature setting, put the

temperature control knob (10) into the «Max» position.

! While holding the iron in a vertical position, aim its sole plate

towards the articles to be ironed and push the steam burst

button (8) to produce a directional strong burst of steam from

the sole plate. Push the button several times with 5-7 seconds

intervals until the article is fully refreshed. If during the process

your water tank (5) runs out of water, disconnect the appli-

ance from the mains outlet, wait till it cools down, refill the tank

and plug the appliance back into the power supply and con-

tinue the process.

Spray

Using the water spray (7) will help when ironing details of the

article (cuffs, trimmings, plackets, etc) or clothes, which demand

«•» (low temperature) ironing, when steam ironing is not pos-

sible. Push the button several times to moisten the material.

Auto shut-off function (for SI-4022)

For safety reasons, your iron will automatically switch off if it’s

left without supervision:

! upright for more than 8 minutes, or

! flat for more than 30-35 seconds.

The operation indicator (11) will start blinking.

The iron will switch on again, when you move it. After that the

operation indicator will stop blinking.

5. When you have finished cleaning or ironing, do not forget to

switch the iron off by putting the steam control knob (9) into

the «0» position, the temperature control knob (10) – to the

minimal position and unplugging the appliance from the mains

supply outlet.

Содержание

Похожие устройства

Turbo steam To eose ironing of dense cotton linen and upholstery articles use the steam burst button 8 engagement of the button 8 during the ironing process generates an extra burst of steam from the sole plate to help remove stubborn creases Burst of steam in a vertical position This function helps to freshen the appearance of curtains jack ets coats etc To use this function take the following steps Follow instructions in paragraph 1 4 of the section Operation instructions While selecting the temperature setting put the temperature control knob 10 info the Max position While holding the iron in a vertical position aim its sole plate towards the articles to be ironed and push the steam burst button 8 to produce a directional strong burst of steam from the sole plate Push the button several times with 5 7 seconds intervals until the article is fully refreshed If during the process your water tank 5 runs out of water disconnect the appli ance from the mains outlet waif till it cools down refill the tank and plug the appliance back into the power supply and con tinue the process Spray Using the water spray 7 will help when ironing details of the article cuffs trimmings plackets etc or clothes which demand low temperature ironing when steam ironing is not pos sible Push the button several times to moisten the material Auto shut off function for SI 4022 For safety reasons your iron will automatically switch off if it s left without supervision upright for more than 8 minutes or flat for more than 30 35 seconds The operation indicator 11 will start blinking The iron will switch on again when you move it After that the operation indicator will stop blinking 5 When you have finished cleaning or ironing do not forget to switch the iron off by putting the steam control knob 9 info the 0 position the temperature control knob 10 to the minimal position and unplugging the appliance from the mains supply outlet 7 ENGLISH Attention Application of the steam ironing function is impossible at temperature setting The Drip Stop system automatically terminates the steam generation process if the selected temperature is too low When the system is activated you may hear a light click

Скачать