Vitek VT-1261 [4/32] English
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Vitek VT-1261 [4/32] English

Vitek VT-1261 [4/32] English
4
ENGLISH
safety or if they are not instructed by this person
on the usage of the unit.
•
Do not use the unit if the power cord or the
power plug is damaged, if the unit works
improperly and after it was dropped or in case
of leakage.
•
If the power cord is damaged, it should be
replaced by the manufacturer, a maintenance
service or similar qualified personnel to avoid
danger.
•
Do not attempt to repair the unit. Do not disas-
semble the unit by yourself, if any malfunction is
detected or after it was dropped, unplug the unit
and apply to any authorized service center from
the contact address list given in the warranty
certificate and on the website www.vitek.ru.
•
Transport the unit in the original package only.
•
Keep the unit out of reach of children and dis-
abled persons.
THE UNIT IS INTENDED FOR HOUSEHOLD USE
ONLY. ITS COMMERCIAL USAGE AND USAGE
IN PRODUCTION AREAS AND WORK SPACES IS
PROHIBITED.
BEFORE THE FIRST USE
After unit transportation or storage at low tem-
perature keep it for at least three hours at room
temperature before switching on.
•
Unpack the iron; remove the protection from the
soleplate (13), if any.
•
Check the unit for damages, do not use the iron
in case of damages.
•
Before switching the iron on, make sure that
your home mains voltage corresponds to the
iron operating voltage.
•
The unit is intended for operation with AC system
and 50 or 60 Hz frequency. The unit does not
need any additional settings for operating with
the required nominal frequency.
•
There may be water residue in the tank (10), this
is normal, as the iron has undergone factory
quality control.
Note: - While the first switching on the heating ele-
ment of the iron burns, therefore occurrence of
foreign smell and a small amount of smoke is pos-
sible, it is normal.
Control knobs, indications and symbols
•
The continuous steam supply knob (3) has
2 fixed positions:
– – steam supply is off;
– – steam supply is on
and one unfixed position:
– – self-clean.
•
Burst of steam button (4) – press the button to
activate the additional steam supply function.
•
Water spray button (5) – press the button to acti-
vate the water spray function.
•
Heating element ON/OFF indicator (7) – when
the indicator lights up, the iron soleplate is heat-
ing up.
•
Temperature control knob (11) – allows to set
the iron soleplate temperature depending on the
type of fabric (see the table below). The knob is
in the position «OFF» – the iron is off.
•
«MAX» maximal water level mark
•
The symbol indicates hot surfaces.
WATER SELECTION
You can use tap water to fill the water tank (10).
Built-in anti-scale system helps to soften water in
order to reduce the scale in the steam chamber,
but if the tap water is hard, it is recommended to
use distilled or demineralized water. It will prolong
service life of the iron.
Note: - Do not fill the water tank (10) with scented
liquids, vinegar, starch solution, descaling
reagents, chemical agents etc.
FILLING THE WATER TANK
Before filling the iron with water, make sure that it
is unplugged.
•
Set the temperature control knob (11) to the
position «OFF», and the continuous steam sup-
ply knob (3) to the position – continuous
steam supply is off.
•
Open the water inlet lid (2) and pour water into
the water tank (10) using the beaker (14) and
then close the lid (2) tight.
Notes:
–
Do not exceed the «MAX» mark (12).
–
If you need to refill water during ironing, always
switch the iron off first and unplug it.
–
After you finish ironing, switch the iron off, wait
until it cools down completely, then open the
water inlet lid (2), turn over the iron and drain
the remaining water.
IRONING TEMPERATURE
Before operation, test the heated iron on a piece of
cloth to be sure that the iron soleplate (13) and the
water tank (10) are clean.
•
Always check the recommended ironing tem-
perature indicated on the tag before ironing.
IM VT-1261.indd 4 9/30/20 10:52 AM

Содержание

Похожие устройства

Скачать