Home
Главная
Bosch
Сетевой перфоратор
GBH 3-28 DFR 061124A000
Руководство по эксплуатации Страница: 18

Bosch GBH 3-28 DFR 061124A000 [18/222] Changing the tool

18 | English

1 609 929 Y58 | (23.3.11) Bosch Power Tools

chuck is used, the application tool could fall out during op-

eration.

– Before inserting, clean the quick change chuck and apply a

light coat of grease to the shank end.

– Grasp the SDS-plus quick change chuck 2 or the quick

change keyless chuck 1 completely with your hand. Slide

the quick change chuck with a turning motion onto the drill

chuck mounting 18 until a distinct latching noise is heard.

– The quick change chuck is automatically locked. Check the

locking effect by pulling the quick change chuck.

Changing the Tool

The dust protection cap 4 largely prevents the entry of drilling

dust into the tool holder during operation. When inserting the

tool, take care that the dust protection cap 4 is not damaged.

 A damaged dust protection cap should be changed im-

mediately. We recommend having this carried out by

an after-sales service.

Inserting SDS-plus Drilling Tools (see figure F)

The SDS-plus drill chuck allows for simple and convenient

changing of drilling tools without the use of additional tools.

– GBH 3-28 DFR: Insert the SDS-plus quick change chuck 2.

– Clean and lightly grease the shank end of the tool.

– Insert the tool in a twisting manner into the tool holder until

it latches itself.

– Check the latching by pulling the tool.

As a requirement of the system, the SDS-plus drilling tool can

move freely. This causes a certain radial run-out at no-load,

which has no effect on the accuracy of the drill hole, as the

drill bit centres itself upon drilling.

Removing SDS-plus Drilling Tools (see figureG)

– Push back the locking sleeve 5 and remove the tool.

Inserting Drilling Tools without SDS-plus (GBH 3-28 DRE)

Note: Do not use tools without SDS-plus for hammer drilling

or chiselling! Tools without SDS-plus and their drill chucks are

damaged by hammer drilling or chiselling.

– Insert a key type drill chuck 16 (see “Changing the Key

Type Drill Chuck”, page 17).

– Open the key type drill chuck 16 by turning until the tool

can be inserted. Insert the tool.

– Insert the chuck key into the corresponding holes of the

key type drill chuck 16 and clamp the tool uniformly.

– Turn the mode selector switch 9 to the “drilling” position.

Removing Drilling Tools without SDS-plus

(GBH 3-28 DRE)

– Turn the sleeve of the key type drill chuck 16 with the drill

chuck key in anticlockwise direction until the drilling tool

can be removed.

Inserting Drilling Tools without SDS-plus (GBH 3-28 DFR)

(see figure H)

Note: Do not use tools without SDS-plus for hammer drilling

or chiselling! Tools without SDS-plus and their drill chucks are

damaged by hammer drilling or chiselling.

– Insert the quick change keyless chuck 1.

– Firmly hold the retaining ring 21 of the quick change

chuck. Open the tool holder by turning the front sleeve 20

until the tool can be inserted. Tightly hold the retaining ring

21 and firmly turn the front sleeve 20 in the direction of the

arrow until a distinct latching noise can be heard.

– Check the tight seating by pulling the tool.

Note: If the tool holder was opened to the stop, then the latch-

ing noise possibly may be heard while closing the tool holder

and the tool holder will not close.

In this case, turn the front sleeve 20 once in the opposite di-

rection of the arrow. Afterwards, the tool holder can be

closed (tightened) again.

– Turn the mode selector switch 9 to the “drilling” position.

Removing Drilling Tools without SDS-plus

(GBH 3-28 DFR) (see figure I)

– Firmly hold the retaining ring 21

of the quick change

chuck. Open the tool holder by turning the front sleeve 20

in the direction of the arrow until the tool can be removed.

Dust Extraction with the Dust Extraction

Attachment (Accessory)

 Dusts from materials such as lead-containing coatings,

some wood types, minerals and metal can be harmful to

one’s health. Touching or breathing-in the dusts can cause

allergic reactions and/or lead to respiratory infections of

the user or bystanders.

Certain dusts, such as oak or beech dust, are considered

as carcinogenic, especially in connection with wood-treat-

ment additives (chromate, wood preservative). Materials

containing asbestos may only be worked by specialists.

– As far as possible, use a dust extraction system suita-

ble for the material.

– Provide for good ventilation of the working place.

– It is recommended to wear a P2 filter-class respirator.

Observe the relevant regulations in your country for the

materials to be worked.

 Prevent dust accumulation at the workplace. Dusts can

easily ignite.

Mounting the Dust Extraction Attachment (see figure J)

For dust extraction, the dust extraction attachment (accesso-

ry) is required. When drilling, the dust extraction attachment

retracts so that the attachment head is always close to the

surface at the drill hole.

– Press the button for depth stop adjustment 10 and remove

the depth stop 11. Press button 10 again and insert the

dust extraction attachment into the auxiliary handle 12

from the front.

– Connect an extraction hose (diameter 19 mm, accessory)

to the extraction sleeve 22 of the dust extraction attach-

ment.

The vacuum cleaner must be suitable for the material being

worked.

– When vacuuming dry dust that is especially detrimental to

health or carcinogenic, use a special vacuum cleaner.

OBJ_BUCH-770-005.book Page 18 Wednesday, March 23, 2011 2:38 PM

Содержание

Похожие устройства

OBJ_BUCH 770 005 book Page 18 Wednesday March 23 2011 2 38 PM 181 English chuckis used the application tool could fall out during op eration Before inser ti ng clean the qui ck change chuck and apply a light coat of grease to the shank end Grasp the SDS plus quick change chuck 2 or the quick Firmly hold the retaining ring 21 of the quick change chuck Open the tool holder by turning the front sleeve 20 until the tool can beinserted Tightlyhold theretainingring 21and firmly turn thefrontsleeve 20in thedirectionofthe arrow until a distinct latching noise can be heard change keyless chuck 1 completely with your hand Slide Check the tight seating by pulling the tool the qui ck change chuck with a turni ng motion onto the dri II Note If the tool holder was opened to thestop then thelatch chuck mounting 18 until a distinct latching noise is heard Thequick changechuck is automatically locked Check the locking effect by pulling the quick change chuck ing noise possibly may be heard while closing the tool holder and the tool holder will not close In this case turn the front sleeve 2Oonce in the opposite di rection of the arrow Afterwards the tool holder can be Changing the Tool closed tightened again The dust protection cap4 largely prevents the entry of drilling Turn the mode sei ector switch 9 to the drill ing position dust into the tool holder during operation When inserting the tool take care that the dust protection cap 4 is not damaged A damaged dust protection cap should be changed im mediately We recommend having this carried out by an after sales service Removing Drilling Tools without SDS plus GBH 3 28DFR seefigure I Firmly hold the retaining ring 21 of the quick change chuck Open the tool holder by turning thefrontsleeve 20 in the direction of the arrow until the tool can be removed Inserting SDS plus Drilling Tools see figure F The SDS plus drill chuck allows for simple and convenient changing of drilling tools without the use of additional tools GBH 3 28 DFR Insert the SDS plus quick change chuck 2 Clean and lightly grease the shank end of the tool Insert the tool in a twisting manner into the tool holder until it latches itself Check the latching by pulling the tool As a requirement of the system theSDS plus drilling tool can Dust Extraction with the Dust Extraction Attachment Accessory Dusts from materials such as lead containing coatings some wood types minerals and metal can be harmful to one s health Touching or breathing in the dusts can cause allergic reactions and or lead to respiratory infections of the user or bystanders Certain dusts such as oak or beech dust are considered move freely This causes a certain radial run out at no load which has no effect on the accuracy of the drill hole as the as cardnogenic especially in connection with wood treat drill bit centres itself upon drilling containing asbestos may only be worked by specialists Removing SDS plus Drilling Tools see figure G Push back the locking sleeve 5 and remove the tool Inserting Drilling Tools without SDS plus GBH 3 28 DRE Note Do not use tools withoutSDS plus for hammer drilling or chiselling Tools withoutSDS plus and their drill chucks are damaged by hammer drilling or chiselling Insert a key type drill chuck 16 see Changing the Key Type Drill Chuck pagel7 ment additives chromate wood preservative Materials As far as possible useadustextractionsystemsuitable for the material Provide for good ventilation of the working place It is recommended towear a P2 filter class respirator Observe the relevant regulations in your country for the materials to be worked Prevent dust accumulation at the workplace Dusts can easily ignite Mounting the Dust Extraction Attachment see figure J Open the key type drill chuck 16 by turning until the tool For dust extraction thedust extraction attachment accesso can be inserted Insert the tool Insert the chuck key into the corresponding holes of the ry is required When drilling the dust extraction attachment retracts so that the attachment head is always close to the key type drill chuck 16 and clamp the tool uniformly Turn the mode selector switch 9 to the drilling position Removing Drilling Tools without SDS plus GBH 3 28 DRE Tur n the si eeve of the key type dri II chuck 16 wi th the dril I chuck key in anticlockwise direction until the drilling tool can be removed surface at the drill hole Press thebutton for depth stop adjustment 10 and remove the depthstop 11 Press button lOagain and insert the dust extraction attachment into the auxiliary handle 12 from the front Connect an extraction hose diameter 19 mm accessory to the extraction sleeve 22 of the dust extraction attach Inserting Drilling Tools withoutSDS plus GBH 3 28 DFR ment The vacuum see figure H worked Note Do not use tools withoutSDS plus for hammer drilling or chiselling Tools withoutSDS plus and their drill chucks are damaged by hammer drilling or chiselling cleanermustbesuitableforthematerial being When vacuuming dry dust that is esped ally detrimental to health or cardnogenic use a special vacuum cleaner Insert the quick change keyless chuck 1 1609 929 Y581 23 3 11 Bosch Power Tools

Скачать