Главная
Skipped breadcrumb items
BGD801Z без акк. и з.у
Инструкция по эксплуатации Страница: 7

Главная
Makita
BGD801Z без акк. и з.у
Инструкция по эксплуатации Страница: 7

Makita BGD801Z без акк. и з.у — инструкция по безопасной эксплуатации и обслуживанию инструмента [7/48]

Превью страниц Страница 7 / 48

Makita BGD801Z без акк. и з.у [7/48] Side handle accessory

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and the

battery cartridge is removed before carrying out

any work on the tool.

Installing or removing wheel point

Fig.4

Loosen the collet nut and insert the wheel point into the

collet nut. Use one wrench to hold the spindle and the

other one to tighten the collet nut securely.

The wheel point should not be mounted more than 8 mm

from the collet nut. Exceeding this distance could cause

vibration or a broken shaft.

Fig.5

To remove the wheel point, follow the installation

procedure in reverse.

CAUTION:

• Use the correct size collet cone for the wheel point

which you intend to use.

OPERATION

Fig.6

Turn the tool on without the wheel point making any

contact with the workpiece and wait until the wheel point

attains full speed. Then apply the wheel point to the

workpiece gently. To obtain a good finish, move the tool

in the leftward direction slowly.

CAUTION:

• Apply light pressure on the tool. Excessive

pressure on the tool will only cause a poor finish

and overloading of the motor.

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and the

battery cartridge is removed before attempting to

perform inspection or maintenance.

• Never use gasoline, benzine, thinner, alcohol or the

like. Discoloration, deformation or cracks may

result.

Replacing carbon brushes

Fig.7

Remove and check the carbon brushes regularly.

Replace when they wear down to the limit mark. Keep

the carbon brushes clean and free to slip in the holders.

Both carbon brushes should be replaced at the same

time. Use only identical carbon brushes.

Fig.8

Insert the top end of slotted bit screwdriver into the notch

in the tool and remove the holder cap cover by lifting it

up.

Fig.9

Use a screwdriver to remove the brush holder caps. Take

out the worn carbon brushes, insert the new ones and

secure the brush holder caps.

Reinstall the holder cap cover on the tool.

To maintain product SAFETY and RELIABILITY, repairs,

any other maintenance or adjustment should be

performed by Makita Authorized Service Centers, always

using Makita replacement parts.

ACCESSORIES

CAUTION:

• These accessories or attachments are

recommended for use with your Makita tool

specified in this manual. The use of any other

accessories or attachments might present a risk of

injury to persons. Only use accessory or

attachment for its stated purpose.

If you need any assistance for more details regarding

these accessories, ask your local Makita Service Center.

Side handle (accessory)

Fig.10

Fig.11

Fig.12

Fig.13

When using the side handle, remove the rubber

protector, insert the side handle on the tool barrel as far

as it will go and rotate it to the desired angle. Then

tighten the handle firmly by turning clockwise.

CAUTION:

• When using the tool without handle, always install

the rubber protector on the tool.

• When installing the rubber protector, always push it

onto the tool so that the top round recessed shape

of the rubber is positioned near the switch

position. .

• Wheel points

• Collet cone (3 mm, 6 mm, 8 mm, 1/4", 1/8")

• Collet nut

• Wrench 13

• Side handle set

• Various type of Makita genuine batteries and

chargers

Makita BGD801Z без акк. и з.у — инструкция по безопасной эксплуатации и обслуживанию инструмента [7/48]

Содержание

Похожие устройства