Home
Главная
Skil
Шлифовальная Машина
7450 LA
Инструкция по эксплуатации Страница: 7

Skil 7450 LA [7/112] Application advice

! be aware that the working of the pressure control

feature is not guaranteed when sanding at lower

speed control settings (1-6)

• On/o

- before switching on the tool, you should place it with

the entire sanding surface on the workpiece

- when switching on, do not apply too much pressure on

the tool

- switch on/o the tool by pulling/releasing trigger F

! be aware of the sudden impact when the tool is

switched on

! before switching off the tool, you should lift it

from the workpiece

• Switch lock

- pull trigger F 2

- press knob G 2 with your thumb

- release the trigger

- unlock the switch by pulling again trigger F 2 and then

releasing it

• Speed control 7 (7460)

For optimal sanding results on dierent materials

- with wheel 2 you can set the desired sanding speed

- always adjust speed to grit size used

- before starting a job, nd the optimal speed and grit by

testing out on spare material

• Holding and guiding the tool 8

! while working, always hold the tool at the

grey-coloured grip area(s)

- guide the tool parallel to the working surface and move

it in circles or in a cross pattern

! do not apply too much pressure on the tool; let

the sanding surface do the work for you

- do not tilt the tool in order to avoid unwanted sanding

marks

- keep ventilation slots K 2 uncovered

• Sanding

- the amount of material removed is determined by the

speed of the sanding disc

- the speed of the sanding disc decreases relative to the

pressure applied to the tool

- switch on/o the tool by pulling/releasing trigger F 2

APPLICATION ADVICE

• For determining the optimal grit (and speed), table 9 can

be used as reference

! always test out first on a piece of scrap material

• For more tips see www.skil.com

MAINTENANCE / SERVICE

• This tool is not intended for professional use

• Always keep tool and cord clean (especially ventilation

slots K 2)

- remove adhering sanding dust with a brush

! disconnect the plug before cleaning

• If the tool should fail despite the care taken in

manufacturing and testing procedures, repair should be

carried out by an after-sales service centre for SKIL

power tools

- send the tool undismantled together with proof of

purchase to your dealer or the nearest SKIL service

station (addresses as well as the service diagram of

the tool are listed on www.skil.com)

ENVIRONMENT

• Do not dispose of electric tools, accessories and

packaging together with household waste material

(only for EU countries)

- in observance of European Directive 2012/19/EC on

waste of electric and electronic equipment and its

implementation in accordance with national law,

electric tools that have reached the end of their life

must be collected separately and returned to an

environmentally compatible recycling facility

- symbol 0 will remind you of this when the need for

disposing occurs

DECLARATION OF CONFORMITY

• We declare under our sole responsibility that the product

described under “Technical data” is in conformity with the

following standards or standardization documents: EN

60745, EN 61000, EN 55014, in accordance with the

provisions of the directives 2004/108/EC, 2006/42/EC,

2011/65/EU

• Technical file at: SKIL Europe BV (PT-SEU/ENG1),

4825 BD Breda, NL

¹ÊÁÂÆÎ¹Æ¼½ÊÇÇ¾¼½Æ

È½Ê¹ÌÁÇÆËŵÆ¿ÁÆ½½ÊÁÆ¿

ÍÊÇÈ½Ɠˁ˅ʿ˂Ê½¼¹Ɠ

Ä¹¾ÁÂÃ¿Ê¹¹¾

ÈÈÊÇÎ¹Ä¹Æ¹¿½Ê

09.12.2013

NOISE/VIBRATION

• Measured in accordance with EN 60745 the sound

pressure level of this tool is 82 dB(A) and the sound

power level 93 dB(A) (standard deviation: 3 dB), and the

vibration 7.7 m/s² (hand-arm method; uncertainty

K = 1.5 m/s²)

• The vibration emission level has been measured in

accordance with a standardised test given in EN 60745; it

may be used to compare one tool with another and as a

preliminary assessment of exposure to vibration when

using the tool for the applications mentioned

- using the tool for dierent applications, or with dierent

or poorly maintained accessories, may signicantly

increase the exposure level

- the times when the tool is switched o or when it is

running but not actually doing the job, may signicantly

reduce the exposure level

! protect yourself against the effects of vibration

by maintaining the tool and its accessories,

keeping your hands warm, and organizing your

work patterns

Содержание

Похожие устройства

I be aware that the working of the pressure control feature Is not guaranteed when sanding at lower speed control settings 1 6 On off before switching on the tool you should place it with the entire sanding surface on the workpiece when switching on do not apply too much pressure on the tool switch on off the tool by pulling releasing trigger F I be aware of the sudden impact when the tool Is switched on before switching off the tool you should lift It from the workpiece Switch lock pull trigger F 5 press knob G with your thumb release the trigger unlock the switch by pullingagain trigger F and then releasing it Speed control 7460 For optimal sanding results on different materials with wheel you can set the desired sanding speed always adjust speed to grit size used before starting a job find the optimal speed and grit by testing out on spare material Holding and guiding the tool while working always hold the tool at the grey coloured grip area s guide the tool parallel to the working surface and move it in circles or in a cross pattern I do not apply too much pressure on the tool let the sanding surface do the work for you do not tilt the tool in order to avoid unwanted sanding marks keep ventilation slots K uncovered Sanding the amount of material removed is determined by the speed of the sanding disc the speed of the sanding disc decreases relative to the pressure applied to the tool switch on off the tool by pulling releasing trigger F send the tool undismantled together with proof of purchase to your dealer or the nearest SKIL service station addresses as well as the service diagram of the tool are listed on www skil com ENVIRONMENT Do not dispose of electric tools accessories and packaging together with household waste material only for EU countries in observance of European Directive 2012 19 EC on waste of electric and electronic equipment and its implementation in accordance with national law electric tools that have reached the end of their life must be collected separately and returned to an environmentally compatible recycling facility symbol will remind you of this when the need for disposing occurs DECLARATION OF CONFORMITY C We declare under our sole responsibility that the product described under Technical data is in conformity with the following standards or standardization documents EN 60745 EN 61000 EN 55014 in accordance with the provisions of the directives 2004 108 EC 2006 42 EC 2011 65 EU Technical file at SKIL Europe BV PT SEU ENG1 4825 BD Breda NL Marijn van der Hoofden Operations Engineering Olaf Dijkgraaf Approval Manager SKIL Europe BV 4825 BD Breda NL 09 12 2013 NOISE VIBRATION Measured in accordance with EN 60745 the sound pressure level of this tool is 82 dB A and the sound power level 93 dB A standard deviation 3dB and the vibration 7 7 m s2 hand arm method uncertainty K 1 5 m s2 The vibration emission level has been measured in accordance with a standardised test given in EN 60745 it may be used to compare one tool with another and as a preliminary assessment of exposure to vibration when using the tool for the applications mentioned using the tool for different applications or with different or poorly maintained accessories may significantly Increase the exposure level the times when the tool is switched off or when it is running but not actually doing the job may significantly reduce the exposure level I protect yourself against the effects of vibration by maintaining the tool and Its accessories keeping your hands warm and organizing your work patterns APPLICATION ADVICE For determining the optimal grit and speed table can be used as reference I always test out first on a piece of scrap material Formoretipsseewww skil com MAINTENANCE SERVICE This tool is not intended for professional use Always keep tool and cord clean especially ventilation slots K rem we adhering sanding dust with a brush I disconnect the plug before cleaning If the tool should fail despite the care taken in manufacturing and testing procedures repair should be carried out by an after sales service centre for SKIL power tools 7