Falmec SINTESI 90 P.E.U. BLACK CUZW90.00P8#ZZZN460F [28/140] Maintenance

CARBON.ZEO FILTER ALARM

Maintenance after about 2000 hours’ use.

Press button

for 5 seconds to reset the counter.

To activate the alarm:

With the hood OFF, press the buttons

and for

3 seconds.

The LED

lights up.

Conrm with button

If the pushbutton panel is completely inactive, before

contacting the Technical assistance service, disconnect

power temporarily to the appliance (about 5“), possibly

by acting on the main switch, to restore normal operation. If this

measure has no eect, contact the Technical assistance service.

MAINTENANCE

Before cleaning or carrying out maintenance operations,

disconnect the equipment by removing the plug or

switching o the main switch.

Do not use detergents containing abrasive, acidic or corrosive

substances or abrasive cloths.

Regular maintenance guarantees proper operation and performance

over time.

Special attention is to be paid to the metal anti-grease lters : fre-

quent cleaning of the lters and their supports ensures that no amma-

ble grease is accumulated.

CLEANING OF EXTERNAL SURFACES

You are advised to clean the external surfaces of the hood at least once

every 15 days to prevent oily substances and grease from sticking to

them. To clean the brushed stainless steel hood, the Manufacturer rec-

ommends using "Magic Steel" wipes.

Alternatively and for all the other types of surfaces, it can be cleaned

using a damp cloth, slightly moistened with mild, liquid detergent or

denatured alcohol.

Complete cleaning by rinsing well and drying with soft cloths.

Do not use too much moisture or water around the push

button control panel and lighting devices in order to pre-

vent humidity from reaching electronic parts.

Do not wash the aps in a dishwasher.

The glass panels can only be cleaned with specic, non-corrosive or

non-abrasive detergents using a soft cloth.

The Manufacturer declines all responsibility for failure to comply with

these instructions.

CLEANING OF INTERNAL SURFACES

Do not clean electrical parts, or parts related to the motor

inside the hood, with liquids or solvents.

For the internal metal parts, see the previous paragraph.

METAL ANTI-GREASE FILTERS

It is advised to frequently wash the metal lters (F) (at least once a

month) leaving them to soak in boiling water and cleaning solution for

1 hour, taking care not to bend them.

Do not use corrosive, acid or alkaline detergents.

Rinse them well and wait for them to be completely dry before reas-

sembling them.

Washing in a dishwasher is permitted.

To extract and insert the metal anti-grease lters see the assembly in-

structions.

(F)

CARBON-ZEO FILTERS

Under normal conditions, they should be regenerated every 18 months

and replaced after 3 years. To regenerate the lter, follow the following

procedure:

- Remove the lter as described in the instructions (Fig. 12).

- Insert lters A, B and C (if any) in a domestic oven at 200°C for about 2

hours.

- When the lter has cooled down, ret the 4 lters onto the metal

structure of the lter.

GREASE DRIP TRAY

It is advisable to clean the tray every 15 days.

Do not use corrosive, acid or alkaline detergents.

For more thorough cleaning, remove the oil collection tray (see gure)

and wash it with hot water and washing up liquid. Rinse it well and wait

for it to be completely dry before reassembling it. They are dishwasher

safe.

SAFETY INSTRUCTIONS AND WARNINGS

These warnings have been drawn up for

your personal safety and those of others.

You are therefore kindly asked to read the

booklet carefully in its entirety before using or

cleaning the equipment. The Manufacturer de-

clines all responsibility for any damage caused

directly, or indirectly, to persons, things and pets

as a consequence of failing to comply with the

safety warnings indicated in this booklet.

Falmec SINTESI 90 P.E.U. BLACK CUZW90.00P8#ZZZN460F [28/140] Maintenance

Содержание

Похожие устройства