Home
Главная
Skil
Перфораторы
1780 NA
Инструкция по эксплуатации Страница: 8

Skil 1780 NA Инструкция по эксплуатации онлайн [8/124] 92728

d) Store idle power tools out of the reach of children and

do not allow persons unfamiliar with the power tool or

these instructions to operate the power tool. Power

tools are dangerous in the hands of untrained users.

e) Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and any

other condition that may affect the power tool’s

operation. If damaged, have the power tool repaired

before use. Many accidents are caused by poorly

maintained power tools.

f) Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are less

likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits etc., in

accordance with these instructions, taking into

account the working conditions and the work to be

performed. Use of the power tool for operations dierent

from those intended could result in a hazardous situation.

5) SERVICE

a) Have your power tool serviced by a qualified repair

person using only identical replacement parts. This

will ensure that the safety of the power tool is maintained.

SAFETY INSTRUCTIONS FOR HAMMERS

GENERAL

• Always check that the supply voltage is the same as the

voltage indicated on the nameplate of the tool (tools with

a rating of 230V or 240V can also be connected to a

220V supply)

• This tool should not be used by people under the age of

16 years

• Do not work materials containing asbestos (asbestos

is considered carcinogenic)

• Never use the tool when cord is damaged; have it

replaced by a qualied person

• Alwaysdisconnectplugfrompowersourcebefore

making any adjustment or changing any accessory

ACCESSORIES

• SKIL can assure awless functioning of the tool only

when the correct accessories are used which can be

obtained from your SKIL dealer

• Use only accessories with an allowable speed matching

at least the highest no-load speed of the tool

BEFORE USE

• Use completely unrolled and safe extension cords with a

capacity of 16 Amps (U.K. 13 Amps)

• Avoid damage that can be caused by screws, nails and

other elements in your workpiece; remove them before

you start working

• Secure the workpiece (a workpiece clamped with

clamping devices or in a vice is held more securely than

by hand)

• Use suitable detectors to find hidden utility lines or

call the local utility company for assistance (contact

with electric lines can lead to re or electrical shock;

damaging a gas line can result in an explosion;

penetrating a water pipe will cause property damage or

an electrical shock)

• Dust from material such as paint containing lead, some

wood species, minerals and metal may be harmful

(contact with or inhalation of the dust may cause allergic

reactions and/or respiratory diseases to the operator or

bystanders); wear a dust mask and work with a dust

extraction device when connectable

• Certain kinds of dust are classied as carcinogenic (such

as oak and beech dust) especially in conjunction with

additives for wood conditioning; wear a dust mask and

work with a dust extraction device when connectable

• Follow the dust-related national requirements for the

materials you want to work with

DURING USE

• Wear ear protectors (exposure to noise can cause

hearing loss)

• Use auxiliary handle(s), if supplied with the tool

(loss of control can cause personal injury)

• Hold power tool by insulated gripping surfaces,

when performing an operation where the cutting

accessory may contact hidden wiring or its own

cord (a cutting accessory contacting a “live” wire may

make exposed metal parts of the power tool “live” and

could give the operator an electric shock)

• Always keep the cord away from moving parts of the tool

• In case of electrical or mechanical malfunction,

immediately switch o the tool and disconnect the plug

• If the cord is damaged or cut through while working, do

not touch the cord, but immediately disconnect the plug

• If the drill bit becomes unexpectedly jammed (causing a

sudden, dangerous reaction), immediately switch o the

tool

• Be aware of the forces that occur as a result of jamming

(especially when drilling metals); always use auxiliary

handle J 2 and take a secure stance

AFTER USE

• When you put away the tool, switch o the motor and

ensure that all moving parts have come to a complete

standstill

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):

• Do not connect the blue (= neutral) or brown (= live) wire

in the cord of this tool to the earth terminal of the plug

• If for any reason the old plug is cut o the cord of this tool,

it must be disposed of safely and not left unattended

USE

• Combined switch for on/o and speed control A 2

• Switch locking for continuous use (possible only when

tool is set for right rotation)

- pull trigger A 2

- press button B 2 with your thumb

- release the trigger

- unlock the switch by pulling again trigger A 2 and

then releasing it

• Speed control for smooth starting 4

• Maximum speed control 5

With wheel C 2 the maximum speed can be adjusted

steplessly from minimum to maximum

• Changing direction of rotation 6

- when not properly set in left/right position, switch A

cannot be activated

- the tool functions at limited speed when set for left

rotation

! change direction of rotation only when tool is at a

complete standstill

• Selecting operating mode 7

- press button E to unlock switch F

Содержание

Похожие устройства

d Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these Instructions to operate the power tool Power tools are dangerous in the hands of untrained users e Maintain power tools Check for misalignment or binding of moving parts breakage of parts and any other condition that may affect the power tool s operation If damaged have the power tool repaired before use Many accidents are caused by poorly maintained power tools f Keep cutting tools sharp and clean Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control g Use the power tool accessories and tool bits etc In accordance with these Instructions taking Into account the working conditions and the work to be performed Use of the power tool for operations different from those intended could result in a hazardous situation 5 SERVICE a Have your power tool serviced by a qualified repair person using only identical replacement parts This will ensure that the safety of the power tool is maintained bystanders wear a dust mask and work with a dust extraction device when connectable Certain kinds of dust are classified as carcinogenic such as oak and beech dust especially in conjunction with additives for wood conditioning wear a dust mask and work with a dust extraction device when connectable Follow the dust related national requirements for the materials you want to work with DURING USE Wear ear protectors exposure to noise can cause hearing loss Use auxiliary handle s If supplied with the tool loss of control can cause personal injury Hold power tool by insulated gripping surfaces when performing an operation where the cutting accessory may contact hidden wiring or Its own cord a cutting accessory contacting a live wire may make exposed metal parts of the power tool live and could give the operator an electric shock Always keep the cord away from moving parts of the tool In case of electrical or mechanical malfunction immediately switch off the tool and disconnect the plug If the cord is damaged or cut through while working do not touch the cord but immediately disconnect the plug If the drill bit becomes unexpectedly jammed causing a sudden dangerous reaction immediately switch off the tool Be aware of the forces that occur as a result of jamming especially when drilling metals always use auxiliary handle J and take a secure stance AFTER USE When you put away the tool switch off the motor and ensure that all moving parts have come to a complete standstill WHEN CONNECTING NEW 3 PIN PLUG U K ONLY Do not connect the blue neutral or brown live wire in the cord of this tool to the earth terminal of the plug If for any reason the old plug is cut off the cord of this tool it must be disposed of safely and not left unattended SAFETY INSTRUCTIONS FOR HAMMERS GENERAL Always check that the supply voltage is the same as the voltage indicated on the nameplate of the tool tools with a rating of 230V or 240V can also be connected to a 220V supply This tool should not be used by people under the age of 16 years Do not work materials containing asbestos asbestos is considered carcinogenic Never use the tool when cord is damaged have it replaced by a qualified person Always disconnect plug from power source before making any adjustment or changing any accessory ACCESSORIES SKIL can assure flawless functioning of the tool only when the correct accessories are used which can be obtained from your SKIL dealer Use only accessories with an allowable speed matching at least the highest no load speed of the tool BEFORE USE Use completely unrolled and safe extension cords with a capacity of 16 Amps U K 13 Amps Avoid damage that can be caused by screws nails and other elements in your workpiece remove them before you start working Secure the workpiece a workpiece clamped with clamping devi ces or i n a vice i s hel d more securely than by hand Use suitable detectors to find hidden utility lines or call the local utility company for assistance contact with electric lines can lead to fire or electrical shock damaging a gas line can result in an explosion penetrating a water pipe will cause property damage or an electrical shock Dust from material such as paint containing lead some wood species minerals and metal may be harmful contact with or inhalation of the dust may cause allergic reactions and or respiratory diseases to the operator or USE Combined switch for on off and speed control A Switch locking for continuous use possible only when tool is set for right rotation pull trigger A 5 press button B with your thumb release the trigger unlock the switch by pulling again trigger A and then releasing it Speed control for smooth starting Maximum speed control With wheel C the maximum speed can be adjusted steplessly from minimum to maximum Changing direction of rotation when not properly set in left right position switch A cannot be activated the tool functions at limited speed when set for left rotation I change direction of rotation only when tool is at a complete standstill Selecting operating mode r press button Eto unlock switch F 8

Скачать