Festool Rotex RO 90 DX FEQ-Plus 571679 [14/94] Warning
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Festool Rotex RO 90 DX FEQ-Plus 571679 [14/94] Warning

Festool Rotex RO 90 DX FEQ-Plus 571679 [14/94] Warning
14
ROTEX
GB
7 Settings
7.1 Electronics
The machine features full-wave electronics
with the following features:
Smooth start-up
The electronically controlled smooth start-up
ensures that the machine starts up jolt-free.
Speed control
You can regulate the speed steplessly with
the adjusting wheel [1-6] in the speed range
(see Technical data). This enables you to op-
timise the cutting speed to suit the surface
(see table).
Constant speed
The preselected motor speed remains con-
stant through electronic control to ensure a
uniform cutting speed even when under load.
Temperature cut-out
The machine power supply is limited and the
speed reduced if the motor exceeds a certain
temperature. The machine continues operat-
ing at reduced power to allow the ventilator
to cool the motor quickly. If the machine
temperature exceeds the maximum permit-
ted value for longer periods, the machine
switches off completely after approx. 40 sec-
onds and can only be switched on again once
the motor has cooled sufficiently.
7.2 Setting sanding motion [3]
The change-over switch [1-2] can be used to
set three different sanding motions.
L
This change-over can only be carried out
with the sanding pad stationary because
the switch is locked during operation.
Coarse sanding, polishing - ROTEX rota-
ry motion
The Rotex rotary motion is a combi-
nation of rotary and eccentric mo-
tions. This position is selected for
sanding with high output (coarse
sanding) and polishing.
Fine sanding - eccentric motion
This position is selected for sanding
with low output for a scratch-free
surface (fine sanding).
Triangular sanding and pad change [4]
This position is used for sanding
with the delta sanding pad and slat
sanding pad; the rotary motion is
blocked.
You can change the sanding pad in
this position.
L
The stop rod [1-8] blocks the in-
stallation of the sanding pad in the
change-over switch positions ROTEX rota-
ry motion and eccentric motion.
7.3 Changing sanding/polishing pad
[5]
L
Only use sanding and polishing pads that
are suitable for the maximum speed spec-
ified.
Tuned to the surface being processed, the
machine can be equipped with two sanding
pads of different hardnesses.
Hard:
Coarse and fine sanding on surfaces.
Sanding edges.
Soft:
Universal for coarse and fine sanding,
for flat and convex surfaces.
When the interface pad [1-12] is fitted on the
sanding pad, strength is reduced = extra
soft.
X
Following the sanding pad change, switch
the change-over switch [1-2] to the de-
sired sanding motion.
7.4 Changing sanding pad [6]
The delta sanding pad DSS-GE-STF-RO90
can be used for sanding close to borders, in
corners or on edges. The slat sanding pad
LSS-STF-RO90 can be used for sanding in
narrow gaps, e.g. louvres.
Observe the following instructions:
Work in corners and on edges tends to sub-
ject the tip to increased stress and results in
increased heat development. In such cases,
work with reduced contact pressure.
Delta sanding pad DSS-GE-STF-RO90
[7]
If the front tip of the StickFix pad [7-1] of
your delta sanding pad is worn, take it off
and turn it 120°.
WARNING
Risk of injury, electric shock
X
Always pull the plug out of the socket be-
fore performing any type of work on the
machine!

Содержание

Похожие устройства

Скачать