![AMERICAN DJ Penta Pix [4/14] Dmx add](/img/pdf.png)
AMERICAN DJ Penta Pix [4/14] Dmx add
![AMERICAN DJ Penta Pix [4/14] Dmx add](/views2/2008153/page4/bg4.png)
ADJ Products, LLC - www.adj.com - Penta Pix Instruction Manual Page 7
Penta Pix System Menu
The LCD backlight will shut o after 30 seconds, to relight
the background, press the MODE button for 5 seconds.
DMX Addr - Set the DMX Address Mode -
1. Press the MODE button until “DMX Addr” is displayed, press
ENTER.
2. The address will now begin to ash, use the UP and DOWN
buttons to nd your desired DMX address, then press ENTER.
DMX Mode - Set the DMX Channel Mode -
1. Press the MODE button until “DMX Mode” is displayed, and
press ENTER.
2. The current DMX channel mode will now begin to ash, use
the UP and DOWN buttons to nd your desired DMX Channel
mode, then press ENTER.
Slave Mode - This will let you set your unit as a slave in
a master/slave conguration.
1. Press the MODE button until “Slave Mode” is displayed. Your
unit will now follow the Master.
Static Color Mode - In this mode you can set a static
color.
1. Press the MODE button until “STATC” is displayed, and press
ENTER.
2. The “01” will now begin to ash. Press ENTER again and use
the UP and DOWN buttons to cycle through the various static
colors.
Dream Mode - This mode is a individual fade mode with
each lens generating a different color.
1. Press the MODE button until “STATC” is displayed, and press
ADJ Products, LLC - www.adj.com - Penta Pix Instruction Manual Page 6
Notice: Be sure to follow gures two and three when making your own
cables. Do not use the ground lug on the XLR connector. Do not con-
nect the cable’s shield conductor to the ground lug or allow the shield
conductor to come in contact with the XLR’s outer casing. Grounding
the shield could cause a short circuit and erratic behavior.
DMX512 IN
3-PIN XLR
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
DMX512
DMX+,DMX-,COMMON
1
2
3
Termination reduces signal errors and
avoids signal transmission problems
and interference. It is always advisable
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
1
2
3
1
2
3
DMX +
DMX -
COMMON
DMX512 OT
3-PIN XLR
Figure 2
Figure 3
1 Ground
1 Ground
XLR Male Socket
XLR Pin Conguration
3 Hot
2 Cold
2 Cold
3 Hot
XLR Female Socket
Pin 3 = Data True (positive)
Pin 2 = Data Compliment (negative)
Pin 1 = Ground
Special Note: Line Termination.
When longer runs of cable are
used, you may need to use a terminator on the last unit to avoid erratic
behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is con-
nected between pins 2 and 3 of a male XLR connector (DATA + and
DATA -). This unit is inserted in the female XLR connector of the last
unit in your daisy chain to terminate the line. Using a cable terminator
(ADJ part number Z-DMX/T) will decrease the possibilities of erratic
behavior.
DMX512 IN
3-PIN XLR
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
DMX512
DMX+,DMX-,COMMON
1
2
3
Termination reduces signal errors and
avoids signal transmission problems
and interference. It is always advisable
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
1
2
3
1
2
3
DMX +
DMX -
COMMON
DMX512 OT
3-PIN XLR
Figure 4
5-Pin XLR DMX Connectors.
Some manufactures use 5-pin DMX-
512 data cables for DATA transmission in place of 3-pin. 5-pin DMX
xtures may be implemented in a 3-pin DMX line. When inserting stan-
dard 5-pin data cables in to a 3-pin line a cable adaptor must be used,
these adaptors are readily available at most electric stores. The chart
below details a proper cable conversion.
Conductor 5-Pin XLR Male (In)3-Pin XLR Female (Out)
Pin 1
Do Not Use
Do Not Use
Pin 3
Pin 2
Pin 1
Pin 3
Pin 2
Not Used
Not Used
Data True (+ signal)
Data Compliment (- signal)
Ground/Shield
3-Pin XLR to 5-Pin XLR Conversion
Penta Pix Set Up
Содержание
- Penta pix 1
- User instructions 1
- Caution 2
- Customer support 2
- Introduction 2
- Unpacking 2
- Warning 2
- Data cable dmx cable requirements for dmx operation 3
- Dmx 512 3
- Ower supply 3
- Adj products llc www adj com penta pix instruction manual page 6 4
- Adj products llc www adj com penta pix instruction manual page 7 4
- And press 4
- And press enter 4
- Be sure to follow figures two and three when making your own cables do not use the ground lug on the xlr connector do not con nect the cable s shield conductor to the ground lug or allow the shield conductor to come in contact with the xlr s outer casing grounding the shield could cause a short circuit and erratic behavior 4
- Dmx add 4
- Dmx mod 4
- Dream mod 4
- Figure 2 4
- Figure 4 4
- In this mode you can set a static color 4
- Notice 4
- Penta pix set up 4
- Penta pix system menu 4
- Pin xlr dmx connectors 4
- Press the mode button until dmx addr is displayed press enter 4
- Press the mode button until dmx mode is displayed 4
- Press the mode button until slave mode is displayed your unit will now follow the master 4
- Press the mode button until statc is displayed 4
- Set the dmx address mode 4
- Set the dmx channel mode 4
- Slave mod 4
- Some manufactures use 5 pin dmx 512 data cables for data transmission in place of 3 pin 5 pin dmx fixtures may be implemented in a 3 pin dmx line when inserting stan dard 5 pin data cables in to a 3 pin line a cable adaptor must be used these adaptors are readily available at most electric stores the chart below details a proper cable conversion 4
- Special note line termination 4
- Static color mod 4
- The 01 will now begin to flash press enter again and use the up and down buttons to cycle through the various static colors 4
- The address will now begin to flash use the up and down buttons to find your desired dmx address then press enter 4
- The current dmx channel mode will now begin to flash use the up and down buttons to find your desired dmx channel mode then press enter 4
- The lcd backlight will shut off after 30 seconds to relight the background press the mode button for 5 seconds 4
- This mode is a individual fade mode with each lens generating a different color 4
- This will let you set your unit as a slave in a master slave configuration 4
- When longer runs of cable are used you may need to use a terminator on the last unit to avoid erratic behavior a terminator is a 110 120 ohm 1 4 watt resistor which is con nected between pins 2 and 3 of a male xlr connector data and data this unit is inserted in the female xlr connector of the last unit in your daisy chain to terminate the line using a cable terminator adj part number z dmx t will decrease the possibilities of erratic behavior 4
- Color change mod 5
- Color fade mod 5
- Dim curv 5
- Manual color mod 5
- Metor mod 5
- Macro mod 6
- Pixel fli 6
- Sound mod 6
- Unit temperatur 6
- Default setting 7
- In this menu you can adjust balance the colors 7
- In this menu you can reset the unit back to its default settings 7
- In this menu you check the current run ning temperature 7
- Master slave set up 7
- On the slave units 7
- Press enter to change the running temperature when you press enter the current temperature setting will begin to flash use the up and down buttons to switch between the tempera ture settings 7
- Press the enter button and either on or off will be dis played to reset the unit use the up or down buttons to display on and press enter 7
- Press the enter button and the led number will begin to blink use the up or down buttons to find the head you would like to balance and press enter 7
- Press the mode button until dfse is displayed 7
- Press the mode button until temp is displayed 7
- Press the mode button until whitebal is displayed 7
- Temperatur 7
- The current running temperature will now be displayed 7
- Universal dmx control 7
- Use the up or down buttons scroll through the colors once you find the color you would like to adjust press enter 7
- Use the up or down buttons to adjust the color 7
- White balanc 7
- 2mm 6 0 11
- 6mm 10 3 11
- Adj products llc www adj com penta pix instruction manual page 20 adj products llc www adj com penta pix instruction manual page 21 11
- Channel value function 11
- Mm 6 1 11
- Penta pix 27 channel mode 11
- Penta pix cad drawing 11
- Penta pix color macro chart 11
- Strobing 0 31 off 32 63 led on 64 95 strobing slow fast 96 127 led on 128 159 pulse strobing slow fast 160 191 led on 192 223 random strobing 224 255 led on 26 master dimmer 0 255 0 100 27 dimmer mode 0 20 standard 21 40 stage 41 60 tv 61 80 architectural 81 100 theatre 101 255 default dimmer setting 11
- Intensity lux 12
- Adj products llc www adj com penta pix instruction manual page 24 adj products llc www adj com penta pix instruction manual page 25 13
- Penta pix notes 13
- Penta pix warranty 13
- Auto sensing voltage 14
- Model penta pix 14
Похожие устройства
- Dynacord PowerSub 312 230 В Руководство по эксплуатации
- Dynacord PSD 215 Руководство по эксплуатации
- AMERICAN DJ Scene Setter 24 Руководство по эксплуатации
- Dynacord PowerMate 1000-3 Руководство по эксплуатации
- Dynacord D-LITE 1000 Руководство по эксплуатации
- Dynacord D 12 Руководство по эксплуатации
- Dynacord COBRA-PWH Руководство по эксплуатации
- Dynacord C 15.2 Руководство по эксплуатации
- Dynacord COBRA-4 FAR Руководство по эксплуатации
- Dynacord A 115A Руководство по эксплуатации
- Dynacord A 118 Руководство по эксплуатации
- Dynacord A 112 Руководство по эксплуатации
- DIALIGHTING WASH ZOOM 19x40 IP67 Руководство по эксплуатации
- DIALIGHTING SUPER MINI Wash 6-15 Руководство по эксплуатации
- DIALIGHTING Spot Led 400 CMY Руководство по эксплуатации
- DIALIGHTING SUPER MINI SPOT 75 Руководство по эксплуатации
- DIALIGHTING MINI SPOT 100 Руководство по эксплуатации
- DIALIGHTING MINI SPOT 150 MKII Руководство по эксплуатации
- DIALIGHTING MINI Wash 7-30 Руководство по эксплуатации
- DIALIGHTING MINI BEAM 75 Руководство по эксплуатации