Coolfort CF-3400 [5/28] English
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Coolfort CF-3400 [5/28] English

Coolfort CF-3400 [5/28] English
5
ENGLISH
Control knobs, indications and symbols
«Continuous Steam Supply» Switch (3) has 3 predetermined
positions (fig. 1):
(15) – Steam Supply is off;
Max (17) – Steam Supply is at maximum;
(16) – Steam Supply is on;
(8) – self-clean.
• Burst of steam button (4) – press the button to activate
the additional steam supply function.
• Water spray button (5) – press the button to activate the
water spray function for dampening the fabrics.
• Temperature control knob (11) – allows to set the iron
soleplate temperature depending on the type of fabric
(see the table below). The knob is in the position «MIN» –
the iron is off.
• «MAX» maximum water level mark (12).
WATER SELECTION
You can use tap water to fill the water tank (10). If tap water
is hard, use distilled or demineralized water, this will prolong
service life of the iron.
Note:
– Do not fill the water tank (10) with scented liquids, vinegar,
starch solution, descaling reagents, chemical agents etc.
FILLING THE WATER TANK
Before filling the iron with water, make sure that it is unplugged.
• Set the temperature control knob (11) to the position
«MIN», and the continuous steam supply knob (3) to the
position (15) – continuous steam supply is off.
• Open the water inlet lid (2).
• Open the water inlet lid (2) and pour water into the water
tank (10) using the beaker (14) and then close the lid
(2) tight.
Notes:
– Do not exceed the «MAX» mark (12).
– If you need to refill water during ironing, always switch
the iron off at first and unplug it.
– After you finish ironing, switch the iron off, wait until it
cools down completely, then open the water inlet lid (2),
turn over the iron and drain the remaining water.
IRONING TEMPERATURE
Before operation, test the heated iron on a piece of cloth
to be sure that the iron soleplate (13) and the water tank
(10) are clean.
• Always check the recommended ironing temperature
indicated on the tag before ironing.
• If the item label is marked with the symbol , do not
iron the item.
• If there is no tag with recommended ironing temperature,
but you know the type of fabric, use the following table to
determine the proper temperature.
Ironing temperature table
Icons Fabric type (temperature)
do not iron
•
Synthetics, nylon, acryl, polyester (low
temperature)
••
Silk/wool (medium temperature)
•••
Cotton (high temperature)
МАХ
Linen (high temperature)
• This table is only valid for smooth materials. Fabrics of
other types (crimped, raised, etc.) are best ironed at low
temperature.
• Sort items by ironing temperature first: synthetics to syn-
thetics, wool to wool, cotton to cotton etc.
• The iron heats up faster than it cools down. For this rea-
son, it is recommended to iron the items which require
low temperature first (for instance, synthetic fabrics).
After that, start ironing at higher temperature (silk/wool).
Cotton and linen items should be ironed last.
• If an item is made of mixed fabrics, the iron should be set
to the lowest temperature (for instance, if an item is 60%
polyester and 40% cotton, it should be ironed at tem-
perature used for polyester ironing «•»).
• If you cannot define the fabric structure, find a spot that
is inconspicuous when the item is being worn and select
the ironing temperature experimentally (always start with
the lowest temperature and raise it gradually until you get
the desired result).
• Corduroy and other fabrics that become glossy quickly
should be ironed strictly in one direction (in the direction
of the pile) with slight pressure.
• To avoid appearance of glossy spots on synthetic and
silk fabrics, iron them backside.
SETTING THE IRONING TEMPERATURE
• Place the iron on its base (9).
• Insert the power plug into the mains socket.
• Turn the control knob (11) to set the required ironing
temperature: «•», «••», «•••» or «MAX», depending on
the type of fabric, the indicator (7) will light up.
• Once the temperature of the soleplate (13) reaches the
set point, the indicator (7) will go out and you can start
ironing.
Note:
– If you are ironing at high temperature but you need to
switch to lower temperature, wait until the soleplate
temperature decreases and the indicator (7) lights up,
and only then you may start ironing.
WATER SPRAY
• You can dampen the fabric by pressing the water spray
button (5) several times.
• Make sure that there is enough water in the water tank
(10).
DRY IRONING
• Place the iron on its base (9).
• Insert the power plug into the mains socket.
• Set the continuous steam supply knob (3) to the position
(15) – the steam supply is off.
• Turn the control knob (11) to set the required ironing
temperature: «•», «••», «•••» or «MAX», depending on
the type of fabric, the indicator (7) will light up.
• Once the temperature of the soleplate (13) reaches the
set point, the indicator (7) will go out and you can start
ironing.
• After you finish ironing, set the temperature control knob
(11) to the “MIN” position.
• Pull the power plug out of the mains socket and let the
iron cool down completely.
STEAM IRONING
While steam ironing it is necessary to set the ironing tem-
perature «•••», «МАХ».

Содержание

Похожие устройства

Скачать