![Makita ea3202s40b Инструкция по эксплуатации онлайн [6/40] 159562](/img/pdf.png)
Makita ea3202s40b Инструкция по эксплуатации онлайн [6/40] 159562
![Makita ea3203s40b Инструкция по эксплуатации онлайн [6/40] 159563](/views2/1175345/page6/bg6.png)
6
10
12
13
14
11
Kickback
‑ When working with the chain saw dangerous kickbacks may
occur.
‑ Kickback occurs when the upper part of the end of the guide
bar inadvertently touches wood or other hard objects (10).
‑ This causes the saw to be thrown back toward the user with
great force and out of control. Risk of injury!
In order to prevent kickback, follow these rules:
‑ Only specially‑trained persons should perform plunge cuts,
i.e., piercing timber or wood with the tip of the saw!
‑ Never apply the end of the bar when starting to make a cut.
‑ Always observe the end of the guide bar. Be careful when
continuing an already started cut.
‑ When starting to cut the chain must be running.
‑ Ensure that the chain is always sharpened correctly. Pay
special attention to the height of the depth limiter.
‑ Never cut several branches at the same time. When cutting
a branch ensure that no other branch is touched.
‑ When crosscutting a trunk be aware of the trunks next to it.
Working behavior/Method of working
‑ Only use the chain saw during good light and visibility periods.
Be aware of slippery or wet areas, and of ice and snow (risk of
slipping). The risk of slipping is extremely high when working
on recently peeled wood (bark).
‑ Never work on unstable surfaces. Make sure that there are
no obstacles in the working area, risk of stumbling. Always
ensure that you have a safe footing.
‑ Never saw above your shoulder height (11).
‑ Never saw while standing on a ladder (11).
‑ Never climb up into trees to perform sawing with the chain
saw.
‑ Do not work leaning too far over.
‑ Guide the chain saw in such a way that no part of your body
is within the elongated swivelling range of the saw (12).
‑ Use the chain saw for sawing wood only.
‑ Avoid touching the ground with the chain saw while it is still
running.
‑ Never use the chain saw for lifting up or removing pieces of
wood or other objects.
‑ Remove foreign objects such as sand, stones and nails found
within the working area. Foreign objects may damage the
sawing device and can cause dangerous kickback.
‑ When sawing precut timber use a safe support (sawing jack,
13). Do not steady the workpiece with your foot, and do not
allow anyone else to hold or steady it.
‑ Secure round pieces against rotation.
‑ For cutting down trees or performing crosscuts the spike
bar (13, Z) must be applied to the wood to be cut.
‑ Before performing a crosscut rmly apply the spike bar to
the timber, only then can the timber be cut with the chain
running. For this the chain saw is lifted at the back handle
and guided with the tubular handle. The spike bar serves as
a center of rotation. Continue by slightly pressing down the
tubular handle and simultaneously pulling back the chain saw.
Apply the spike bar a little bit deeper and once again lift the
back handle.
‑ When the timber must be pierced for cutting or longitudi-
nal cuts are to be performed it is urgently recommended
to have this carried out by specially trained persons
only (high risk of kickback).
‑ Do longitudinal - lengthwise - cuts at the lowest possible
angle (14). Be very careful when doing this type of cut, as
the spike bar cannot grip.
‑ The saw must be running whenever you remove the chain
saw from the wood.
‑ When performing several cuts the throttle lever must be
released in between.
Содержание
- Ea3200s ea3201s ea3202s ea3203s 1
- Important 1
- Instruction manual 1
- Table of contents 2
- Thank you for purchasing a makita product 2
- Delivery inventory 3
- Symbols 3
- Safety precautions 4
- Service 8
- Packing 9
- Technical data 9
- 14 11 12 10 10
- 20 22 23 21 10
- Denomination of components 10
- Caution 11
- Mounting the guide bar and saw chain 11
- Only for models with fastening nuts on the sprocket guard 11
- Putting into operation 11
- Tightening the saw chain 12
- Checking the chain tension 13
- Retightening the saw chain 13
- Caution 14
- Mounting the guide bar and saw chain 14
- Only for the quickset guide bar 14
- Checking the chain tension 15
- Retensioning the saw chain 15
- Tensioning the saw chain 15
- Caution 16
- Mounting the guide bar and saw chain 16
- Only for models with quick ten sioner on sprocket guard tlc 16
- Tightening the saw chain 17
- Checking the chain tension 18
- Engaging the chain brake braking 18
- For all models chain brake 18
- Retensioning the saw chain 18
- Avoid skin and eye contact 19
- Caution 19
- Chain oil 19
- Fuel mixture 19
- The storage of fuel 19
- Avoid skin and eye contact 20
- Filling fuel and chain oil 20
- Follow the safety precautions 20
- Important note on bio degradable chain oils 20
- Never use waste oil 20
- Waste oil 20
- Adjusting the chain lubrication 21
- Checking the chain lubrication 21
- Cold start choke 22
- Cold starting 22
- Combination switch in safety position 22
- Engine off 22
- Starting the engine 22
- Stopping the engine 22
- Warm start on 22
- Warm starting 22
- Checking the chain brake 23
- Adjusting the carburetor 24
- Service 24
- Maintenance 25
- Mm 25 0 4 mm 25 25
- Sharpening the saw chain 25
- Chain type 092 91vg 492 91px 290 90sg 26
- Files and how to work with them 26
- Cleaning the guide bar 27
- Cleaning the inside of the sprocket guard 27
- Service 27
- Replacing the saw chain 28
- Cleaning the air filter 29
- Checking the ignition spark 30
- Checking the muffler screws 30
- Replacing the spark plug 30
- Mounting the fan housing 31
- Replacing the return spring pack 31
- Replacing the starter cable replacing the return spring pack replacing the starter spring 31
- Replacing the starter spring 31
- Cleaning the air filter compartment fan com partment 32
- Cleaning the cylinder fins 32
- Replacing the suction head 32
- Instructions for periodic maintenance 33
- Guarantee 34
- Maintenance and repair 34
- Service spare parts and guarantee 34
- Spare parts 34
- Trouble shooting 35
- Ea3200s ea3201s ea3202s ea3203s 36
- Extract from the spare parts list 36
- Ea3200s ea3201s ea3202s ea3203s 37
- Extract from the spare parts list 37
- Spare parts 37
- Ec declaration of conformity 38
- Makita corporation 40
Похожие устройства
- Makita ea3203s40b Инструкция по эксплуатации
- Makita rp0900 Инструкция по эксплуатации
- Makita hs7100 Инструкция по эксплуатации
- Makita hs6100 Инструкция по эксплуатации
- Makita dhr202rfe Инструкция по эксплуатации
- Makita ld080p Инструкция по эксплуатации
- Makita hr2811ft Инструкция по эксплуатации
- Makita jr3070ct Инструкция по эксплуатации
- Makita jr3060t Инструкция по эксплуатации
- Makita jr3050t Инструкция по эксплуатации
- Makita ddf444rfe Инструкция по эксплуатации
- Makita ddf453rfe Инструкция по эксплуатации
- Makita ddf343she Инструкция по эксплуатации
- Makita ddf453sye Инструкция по эксплуатации
- Makita bo5041 Инструкция по эксплуатации
- Makita 1002ba Инструкция по эксплуатации
- Makita hr2611ft(x5) Инструкция по эксплуатации
- Makita 5477nb Инструкция по эксплуатации
- Makita dbc3310 Инструкция по эксплуатации
- Makita dbc400 Инструкция по эксплуатации
Скачать
Случайные обсуждения