![Supermicro SYS-1028R-WC1RT — технические характеристики серверной системы и компонентов [125/128]](/icons/site-icon-64.png){kind=icon}
Supermicro SYS-1028R-WC1RT — технические характеристики серверной системы и компонентов [125/128]
Превью страниц
Страница 125 /
128
![Supermicro SYS-1028R-WC1RT [125/128] Drive bays](/views2/1308771/page125/bg7d.png)
B-1
Appendix B: System Specifi cations
Appendix B
System Specifi cations
Processors
Single or dual Intel® Xeon E5-2600 v3/v4 Series processors
Note: If only a single processor is populated, then slot SXB1B (PCIe x16) and SXB2 (PCIe
x16) will NOT be functional.
Note: Please refer to our web site for a complete listing of supported processors.
Chipset
Intel PCH-C612 Chipset
BIOS
128 MB SPI AMI BIOS® SM Flash UEFI BIOS
Memory Capacity
Sixteen (16) DIMM slots that can support up to 2048 GB of ECC
RDIMM or LRDIMM DDR4 2400/2133/1866/1600 MHz speed memory in
1 GB, 2 GB, 4 GB, 8 GB, 16 GB, 32 GB, 64 GB and 128 GB size @ 1.2V voltage.
Note: See Section 5-6 for details.
Drive Bays
Contains ten (10) hot-swap drive bays to house SAS/SATA drives. Two additional
optional NVMe drives can be added with an optional add-on card and two
cables.
Expansion Slots
Two full-height, 6.6" length PCI-E 3.0 x16 cards with use of riser card (included)
Serverboard
X10DRW-i(T)
Dimensions: (LxW) 13.05" (L) x 12.80" (W) (331.47 mm x 325.12 mm))
Chassis
SC116AC-R706WBP(1U Rackmount)
Dimensions: (WxHxD) 17.2 x 1.7 x 23.5 in. (437 x 43 x 597 mm)
Содержание
384- Warning handling of lead solder materials used in this product may expose you to lead a chemical known to the state of california to cause birth defects and other reproductive harm
- Printed in the united states of america
- Manual organization
- Preface
- About this manual
- Table of contents
- Chapter 2 server installation
- Chapter 1 introduction
- Chapter 5 advanced serverboard setup
- Chapter 4 standardized warning statements for ac systems
- Chapter 3 system interface
- Chapter 7 bios
- Chapter 6 advanced chassis setup
- Appendix b system specifi cations
- Appendix a bios error beep codes
- Introduction
- Chapter 1
- 1 overview
- Sas sata
- Processors
- Memory
- 2 serverboard features
- Superserve
- System power
- Rear i o ports
- Pci expansion slots
- Hard drive subsystem
- 3 server chassis features
- Front control panel
- Superserve
- Manageability engine me
- Intel intelligent power node manager ipnm
- Cooling system
- 6 advanced power management
- Left slot
- Figure 1 1 intel pch c612 chipset system block diagram
- Chapter 1 introduction
- Wio slots
- Upper lower pcie x16 pcie x16
- Sxb2 pcie x16
- Right slot
- Processor
- Note this is a general block diagram please see chapter 5 for details
- Superserve
- 4 contacting supermicro
- Server installation
- Choosing a setup location
- Chapter 2
- 3 preparing for setup
- 2 unpacking the system
- 1 overview
- Rack precautions
- 4 warnings and cautions
- Superserve
- Server precautions
- Reliable ground
- Reduced airfl ow
- Rack mounting considerations
- Mechanical loading
- Circuit overloading
- Ambient operating temperature
- Superserve
- 5 rack mounting instructions
- Inner rail extension
- Superserve
- Outer rails
- Superserve
- Installing the chassis into a telco rack
- 1 overview
- System interface
- Chapter 3
- 2 control panel buttons
- Universal information led
- 3 control panel leds
- The chassis includes externally accessible sas sata nvme drives each drive carrier displays two status leds on the front of the carrier
- Superserver 1027r 73dbrf user s manual
- Status led
- Led color state status
- Activity led
- 4 drive carrier leds
- Warning defi nition
- Standardized warning statements for ac systems
- Chapter 4
- 1 about standardized warning statements
- ןה תואבה תורהצהא ינפמ שמתשמה תא ריהזהל תנמ לע היישעתה ינקת יפ לע תורהז הלבח ןה תואבה תורהצהא ינפמ שמתשמה תא ריהזהל תנמ לע היישעתה ינקת יפ לע תורהז הלבח ה וא תולאש שיו הדימב תירשפא תיזיפי יהשלכ היעבב תולקתרוציל שי הכימת תקלחמ םע רשק רידגהל וא ןיקתהל םיאשר דבלב םיכמסומ םיאנכט ורקימרפוס לש תינכט תאה םיביכר אורקל שי ורקימרפוס יזראמב םיביכרה תרדגה וא תנקתה ינפל ואולמב חפסנה תא
- ןונקת תורהצהאהרהז
- ﻲﻓ ﻚﻧا نأ ﻦﻜﻤﯾ ﺔﻟﺎﺣ ﻲﻓ ﺐﺒﺴﺘﺗ ﺔﺑﺎﺻا ﺔﯾﺪﺴﺟ ﺰﻣﺮﻟا اﺬھ ﻲﻨﻌﯾ ﺮﻄﺧ ﺮﯾﺬﺤﺗ نأ ﻞﺒﻗ يأ ﻰﻠﻋ ﻞﻤﻌﺗ تاﺪﻌﻣ ﻛﻢﻠﻋ ﻰﻠﻋ ﻦ ﻦﻋ ﺔﻤﺟﺎﻨﻟا ﺮطﺎﺨﻤﻟﺎﺑ ﺮﺋاوﺪﻟا ﺔﯿﺋﺎﺑﺮﮭﻜﻟا ﻛوﺔﯾارد ﻰﻠﻋ ﻦ رﺎﻤﻤﻟﺎﺑتﺎﺳ ﺔﯿﺋﺎﻗﻮﻟا ﻟ ﻊﻨﻤعﻮﻗو يأثداﻮﺣ ﻢﻗر مﺪﺨﺘﺳا نﺎﯿﺒﻟا صﻮﺼﻨﻤﻟا ﺔﯾﺎﮭﻧ ﻲﻓ ﺮﯾﺬﺤﺗ ﻞﻛ رﻮﺜﻌﻠﻟ ﺎﮭﺘﻤﺟﺮﺗ
- ﻟا تادﺎﺷرإ ﺮﻗاﺐﯿﻛﺮﺘ ﻞﯿﺻﻮﺗ ﻞﺒﻗ ﻰﻟإ مﺎﻈﻨﻟا ﺔﻗﺎﻄﻠﻟ رﺪﺼﻣ
- אורקל שי רוקמל תכרעמה רוביח ינפל הנקתה תוארוה תאחתמ
- Installation instructions
- לע ךמתסמ הז רצומנגהה תעינמל םינבמב תנקתומה יכ אדוול שי ילמשח רצק רצקה ינפמ ןגמה רישכמה ילמשחהמ רתוי אל אוה
- Circuit breaker
- ﻦﻣ ﺪﻛﺄﺗ نأ ﻢﯿﯿﻘﺗ زﺎﮭﺠﻟا ﻟاﻲﺋﺎﻗﻮ ﺲﯿﻟ ﻦﻣ ﺮﺜﻛأ
- ﺞﺘﻨﻤﻟا اﺬھ ﻰﻠﻋ ﺪﻤﺘﻌﯾ تاﺪﻌﻣ ﺔﯾﺎﻤﺤﻟا ةﺮﯿﺼﻘﻟاﺮﺋاوﺪﻟا ﻦﻣ ﺎﮭﺘﯿﺒﺜﺗ ﻢﺗ ﻲﺘﻟا ﻲﻓ ﻰﻨﺒﻤﻟا
- Power disconnection warning
- ﻞﺼﻓ ﺐﺠﯾ مﺎﻈﻨﻟا ﻊﯿﻤﺟ ﻦﻣردﺎﺼﻣ ﺔﻗﺎﻄﻟا ﺔﻟازإو ءﺎﺑﺮﮭﻜﻟا ﻚﻠﺳ ﻦﻣ ةﺪﺣو داﺪﻣا ﺔﻗﺎﻄﻟا ﻞﺒﻗ ﻰﻟإ لﻮﺻﻮﻟا ﺔﯿﻠﺧاﺪﻟا ﻖطﺎﻨﻤﻟا ﻟﻞﻜﯿﮭﻠ ﺔﻟازإ وأ ﺖﯿﺒﺜﺘﻟ تﺎﻧﻮﻜﻣ زﺎﮭﺠﻟا
- למשחה תורוקמ לכמ תכרעמה תא קתנל שי ריסהל שיו קפסהמ ילמשחה לבכ תא נקתה ךרוצל זראמה לש ימינפה קלחל השיג ינפלת רסה ואת םיביכר
- ילמשח קותינ ינפמ הרהזא
- הרהזא
- הרהזא שר דבלב ךמסומ תווצתא ףילחהל ןיקתהל יא דויצה רובע תוריש תתל וא דויצה
- Equipment installation
- ﻦﯿﺑرﺪﻤﻟاو و ﺐﯿﻛﺮﺘﻟلاﺪﺒﺘﺳا وأ ﺔﻣﺪﺧ زﺎﮭﺠﻟا اﺬھ ﺢﻤﺴﯾ نأ ﺐﺠﯾ ﻂﻘﻓ ﻦﯿﻠھﺆﻤﻟا ﻦﯿﻔظﻮﻤﻠﻟ
- Restricted area
- ﺺﯿﺼﺨﺗ ةﺪﺣﻮﻟا هﺬھ ﻲﻓ ﺎﮭﺒﯿﻛﺮﺘﻟ ﻖطﺎﻨﻣ ةرﻮﻈﺤﻣ ﻢﺗ ﺻﻮﻟا ﻦﻜﻤﯾﻰﻟإ لﻮ ﺔﻘﻄﻨﻣ ةرﻮﻈﺤﻣ ﻂﻘﻓ ماﺪﺨﺘﺳا لﻼﺧ ﻦﻣ ﺔﺻﺎﺧ ةادأ وأ يأ ﻼﻟ ىﺮﺧأ ﺔﻠﯿﺳونﺎﻣﻷ حﺎﺘﻔﻣو ﻞﻔﻗ
- תרזעב תנתינ השיגה השיג תלבגה םהב שיש םירוזאב הדיחיה תא ןיקתהל שי דכו לוענמ חתפמ דבלב החטבא ילכ
- תלבגומ השיג םע רוזא
- הרהזא
- Battery handling
- ﺮﻄﺧ كﺎﻨھ ﻦﻣ لاﺪﺒﺘﺳا ﺔﻟﺎﺣ ﻲﻓ رﺎﺠﻔﻧا ﺔﯾرﺎﻄﺒﻟا ﺔﺤﯿﺤﺻ ﺮﯿﻏ ﺔﻘﯾﺮﻄﺑ ﻚﯿﻠﻌﻓ ﺔﯾرﺎﻄﺒﻟا لاﺪﺒﺘﺳا ﻂﻘﻓ عﻮﻨﻟا ﺲﻔﻨﺑ ﺎﮭﻟدﺎﻌﯾ ﺎﻣ وأ ﺎﻤﻛﺖﺻوأ ﺔﻌﻨﺼﻤﻟا ﺔﻛﺮﺸﻟا ﮫﺑ تﺎﯾرﺎﻄﺒﻟا ﻦﻣ ﺺﻠﺨﺗ ﻟ ﺎﻘﻓو ﺔﻠﻤﻌﺘﺴﻤﻟاﺔﻌﻧﺎﺼﻟا ﺔﻛﺮﺸﻟا تﺎﻤﯿﻠﻌﺘ
- תנכס תמייקץוציפ הניקת אל ךרדב הפלחוהו הדימב הללוסה לש ףילחהל שי גוסב הללוסה תא מ םאותה תרבחלמומ ןרציתצ תוללוסה קוליס תושמושמה עצבל שי ןרציה תוארוה יפל
- הרהזא
- קפס לש דחא רוביחמ רתוי שי הדחיל תא ריסהל שי ןקורל תנמ לע םירוביחה לכ חיה תאי הד
- הרהזא
- דחא קפסמ רתוי םייק םא
- Redundant power supplies
- ﺪﻗ اﺬﮭﻟ نﻮﻜﯾ ﻟازﺎﮭﺠ تﻻﺎﺼﺗا ةﺪﻋ تاﺪﺣﻮﺑ ﺔﻗﺎﻄﻟا داﺪﻣا ﺔﻟازإ ﺐﺠﯾ تﻻﺎﺼﺗﻻا ﺔﻓﺎﻛ لﺰﻌﻟ ﻟاةﺪﺣﻮ ﻦﻋ ءﺎﺑﺮﮭﻜﻟا
- Backplane voltage
- كﺎﻨھ ﺮﻄﺧ ﻦﻣ ﻲﺋﺎﺑﺮﮭﻜﻟا رﺎﯿﺘﻟا ﻰﻠﻋ ةدﻮﺟﻮﻤﻟا ﺔﻗﺎﻄﻟاوأ ﺔﺣﻮﻠﻟا نﻮﻜﯾ ﺎﻣﺪﻨﻋمﺎﻈﻨﻟا ﻞﻤﻌﯾ ﺪﻨﻋ ارﺬﺣ ﻦﻛ ﺔﻣﺪﺧ زﺎﮭﺠﻟا اﺬھ
- ירוחאה לנפב חתמ
- זא הרה זא הרה ךלהמב רהזיהל שי תכרעמה לועפת ןמזב ירוחאה לנפב חתמ תנכס תמייק הדובעה
- Comply with local and national electrical codes
- تاﺪﻌﻤﻟا ﺐﯿﻛﺮﺗ ﺔﯿﺋﺎﺑﺮﮭﻜﻟا ﻠﻟ ﻞﺜﺘﻤﯾ نأ ﺐﺠﯾ ﻦﯿﻧاﻮﻘﺔﯿﻨطﻮﻟاو ﺔﯿﻠﺤﻤﻟا ﺔﻘﻠﻌﺘﻤﻟا ءﺎﺑﺮﮭﻜﻟﺎﺑ
- יצראה למשחה יקוח םואית
- הרהזא הרהזא תנקתה םייצראהו םיימוקמה למשחה יקוחל תמאות תויהל תבייח דויצה
- Product disposal
- ﻲﺋﺎﮭﻨﻟا ﺺﻠﺨﺘﻟا ﻦﻣ ﺞﺘﻨﻤﻟا اﺬھ ﮫﻌﻣ ﻞﻣﺎﻌﺘﻟا ﻲﻐﺒﻨﯾ ﻟ ﺎﻘﻓو ﻊﯿﻤﺠﺔﯿﻨطﻮﻟا ﺢﺋاﻮﻠﻟاو ﻦﯿﻧاﻮﻘﻟا ﺪﻨﻋ
- רצומה קוליס
- הרהזא הרהזא ו תויחנהל םאתהב תויהל בייח הז רצומ לש יפוס קוליס הנידמה יקוח
- Easy swap fan warning
- ﻦﻜﻤﻤﻟا ﻦﻣ حواﺮﻤﻟا نأ لاﺰﺗ ﻻ ﺔﻟازإ ﺪﻨﻋروﺪﺗ ﺔﻠﺘﻛ ﺔﺣوﺮﻤﻟا ﻞﻜﯿﮭﻟا ﻦﻣ ﺐﺠﯾ ءﺎﻘﺑإ ﻊﺑﺎﺻﻷا وﻲﻏاﺮﺒﻟا تﺎﻜﻔﻣ ءﺎﯿﺷﻷا ﻦﻣ ﺎھﺮﯿﻏو اﺪﯿﻌﺑ ﻦﻋ تﺎﺤﺘﻔﻟا ﻲﻓ ﺔﻠﺘﻛ ﺔﺣوﺮﻤﻟا
- הרהזא יקלח תא םיריסמ רשאכ שי םידבוע ןיידע םיררוואמהו ןכתי זראמהמ ררוואמה קיחרהללררוואמה ךותב םיחתפהמ םינוש הדובע ילכו תועבצאה תא חוטב קחרמ
- Power cable and ac adapter
- אתמו םיילמשחמ י
- ﻞﻤﺤﺗ ﻲﺘﻟاﺔﻣﻼ
- ﺐﯿﻛﺮﺗ ﺪﻨﻋ ماﺪﺨﺘﺳا ﺐﺠﯾ زﺎﮭﺠﻟا و ﻞﯿﺻﻮﺘﻟا تﻼﺑﺎﻛ ﺔﯿﺋﺎﺑﺮﮭﻜﻟا تﻼﺑﺎﻜﻟا تﻻﻮﺤﻣو ددﺮﺘﻤﻟا رﺎﯿﺘﻟا نأ يأ ماﺪﺨﺘﺳا تﻼﺑﺎﻛ تﻻﻮﺤﻣو ىﺮﺧأ ﺐﺒﺴﺘﯾ ﻲﻓ ﻞﻄﻋ ثوﺪﺣ ﻖﯾﺮﺣ وأ ﻲﺘﻟا ﻚﻟ ﺎھﺮﯿﻓﻮﺗ ﻢﺗ ﺞﺘﻨﻤﻟا ﻊﻣ ul وأ csa ﺔﯿﺋﺎﺑﺮﮭﻜﻟا ةﺰﮭﺟﻷا داﻮﻣو نﻮﻧﺎﻗ ﺔﻣﻼﺴﻟا ماﺪﺨﺘﺳا ﺮﻈﺤﯾ تﻼﺑﺎﻜﻟا ﻞﺒﻗ ﻦﻣ ةﺪﻤﺘﻌﻣ
- ةﺰﮭﺟأ ىﺮﺧأ ﺔﯿﺋﺎﺑﺮﮭﻛ ﺮﯿﻏ تﺎﺠﺘﻨﻤﻟا ﺔﻨﯿﻌﻤﻟا ﻞﺒﻗ ﻦﻣ يﻷ
- רשא וא הלקתל םורגל לוכי רחא םאתמ וא לבכ לכב שומיש ךכ םשל וקפוסו ודעונ טב יקוחו למשח ירישכמב שומיש יקוח יפ לע ילמשח רצק רוסיא םייק תוחי ב םיכמסומה םילבכב שמתשהל
- רחא ילמשח רצומ לכ רובע דבלב ורקימקרפוס ידי לע ןיוצ אלש
- לש דוק םהילע עיפומ ראשכ
- הרהזא םימאתמו םיקפס םילבכב שמתשהל שי רצומה תא םיניקתמ רשאכ
- ב וא
- Unpacking
- Chapter 5
- Advanced serverboard setup
- 1 handling the serverboard
- Connecting data cables
- Superserve
- Connecting power cables
- 2 connecting cables
- With both hands press the mezzanine card down into the slot
- P1 dimmc2
- P1 dimmc1
- Image of the mezzanine card
- For sas 3 support be sure to follow the instructions below to install the mezzanine card on the aom pci e 3 slot located at j35
- Chapter 5 advanced serverboard setup
- Aom pcie 3 x16 slot at j35
- After installing the motherboard in the chassis align the mezzanine card with the aom pci e 3 slot j35 on the motherboard
- 3 mezzanine card installation
- Superserve
- Jf1 contains header pins for various front control panel connectors see figure 5 1 for the pin locations of the various front control panel buttons and led indicators
- Figure 5 1 control panel header pins
- Connecting the control panel
- Chapter 5 advanced serverboard setup
- All jf1 wires have been bundled into a single cable to simplify this connection make sure the red wire plugs into pin 1 as marked on the board the other end connects to the control panel pcb board located just behind the system status leds on the chassis use the 70 cm 20 pin to 20 pin 20 awg front control cable cbl 0335l to connect to the control panel connections
- 4 rear i o ports
- Superserve
- Installing an lga 2011 processor
- 5 installing the processor and heatsink
- Superserve
- Superserve
- Installing and removing a passive cpu heatsink
- Memory support
- Dimm installation
- 6 installing memory
- Cpus 6 dimms
- Cpus 4 dimms
- Cpus 16 dimms
- Cpu corresponding dimm modules
- Cpu 5 8 dimms
- Cpu 4 dimms
- Cpu 2 dimms
- Superserve
- R wc1r t user s manual
- Processors and their corresponding memory modules
- Processor and memory module population for optimal performance
- Number of cpus dimms cpu and memory population confi guration table for memory to work properly please follow the instructions below
- Follow the tables below when installing memory
- Dimm module population table
- Cpus 9 16 dimms
- Cpus 8 dimms
- Other important notes and restrictions
- Gb 8 gb 1 v 1 v 1 v 1 v
- For the memory modules to work properly please install dimm modules of the same type same speed and same operating frequency mixing of rdimms udimms or lrdimms is not allowed do not install both ecc and non ecc memory modules on the same serverboard
- E5 2600 v3 e5 2600 v4 e5 2600 v3 e5 2600 v4
- Dpc 2 dpc
- Dimm capacity gb
- Chapter 5 advanced serverboard setup
- Using ddr4 dimms with different operating frequencies is not allowed all channels in a system will run at the lowest common frequency
- Speed mt s voltage v slots per channel spc and dimms per channel dpc
- Slots per channel
- Ranks per dimm and data width
- Populating rdimm lrdimm memory modules
- Populating rdimm lrdimm ddr4 memory modules
- X10drw i t
- Superserve
- R wc1r t user s manual
- P1 dimmc2
- Figure 5 5 x10drw i t layout
- Caution 1 to avoid damaging the motherboard and its components please do not use a force greater than 8 lb inch on each mounting screw during motherboard installation 2 some components are very close to the mounting holes please take precautionary measures to prevent damage to these components when installing the motherboard to the chassis
- 7 serverboard details
- Jumper description default setting
- Connectors description
- Chapter 5 advanced serverboard setup
- X10drw i t led indicators
- X10drw i t jumpers
- X10drw i t connectors
- Led description state status
- Superserve
- R wc1r t user s manual
- Note 3 for the latest cpu memory updates please refer to our website at www supermicro com
- Note 2 for sxb2 cpu2 pci e 3 x16 slot to work properly please use the smc proprietary riser card pn rsc r2uw 2e8r
- Note 1 for sxb1a sxb1b sxb1c pci e slot to work properly please use an smc proprietary riser card e g rsc r1uw 2e16 in the slot
- Connectors description
- Power button pin defi nitions jf1
- Power button
- Chapter 5 advanced serverboard setup
- Atx power 24 pin connector pin defi nitions jpwr1
- A 24 pin main power supply connector jpwr1 and two 8 pin cpu power connectors jpwr2 jpwr3 are located on the serverboard these power connectors meet the ssi eps 12v specifi cation and must be connected to your power supply to provide adequate power to the system see the tables on the right for pin defi nitions
- 8 connector defi nitions
- Warning to provide adequate power supply to the serverboard be sure to connect the 24 pin atx power jpwr1 and the two 8 pin power connectors jpwr2 jpwr3 to the power supply failure to do so may void the manufacturer warranty on your power supply and serverboard
- V 8 pin power connector pin defi nitions
- The power button connection is located on pins 1 and 2 of jf1 momentarily contacting both pins will power on off the system this button can also be confi gured to function as a suspend button with a setting in the bios see chapter 7 to turn off the power when the system is in suspend mode press the button for 4 seconds or longer refer to the table on the right for pin defi nitions
- Power connectors
- Superserve
- Power led pin defi nitions jf1
- Power led
- Nmi button pin defi nitions jf1
- Nmi button
- Lan ports lan1 2 pin defi nition
- Ethernet ports
- Chassis intrusion pin defi nitions
- Chassis intrusion
- Chapter 5 advanced serverboard setup
- A video vga port is located next to usb 0 1 on the i o backplane refer to the serverboard layout below for the location
- A chassis intrusion header is located at jl1 on the serverboard attach an appropriate cable from the chassis to inform you of a chassis intrusion when the chassis is opened
- Video connection
- Two ethernet ports lan1 lan2 are located on the i o backplane these ethernet ports support 10g lan connections on the x10drw it and gigabit lan connections on the x10drw i in addition an ipmi_ dedicated lan that supports gigabit lan is located above usb 0 1 ports on the backplane all ethernet ports accept rj45 type cables please refer to the led indicator section for lan led information
- The power led connection is located on pins 15 and 16 of jf1 refer to the table on the right for pin defi nitions
- The non maskable interrupt button header is located on pins 19 and 20 of jf1 refer to the table on the right for pin defi nitions
- Universal serial bus usb
- Trusted platform module header pin defi nitions jtpm1
- Tpm port 80 header
- Superserve
- R wc1r t user s manual
- Front panel usb 3 4 5 pin defi nitions
- Four usb 3 ports usb 0 1 usb 2 3 are located on the i o backpanel in addition an internal usb header located next to s sata0 also provides two usb 3 connections usb 4 5 for front panel support cables are not included see the tables on the right and below for pin defi nitions
- Bp usb 3 0 1 2 3 pin defi nitions
- A trusted platform module port 80 header located at jtpm1 provides tpm support and port 80 connection use this header to enhance system performance and data security see the table on the right for pin defi nitions
- C connector
- C connection on your system
- A system management bus header for ipmi 2 is located at jipmb1 connect the appropriate cable here to use the ipmb
- Three sgpio serial link general purpose input output headers are located on the serverboard i sgpio 1 supports i sata 0 3 and i sgpio 2 supports i sata 4 5 s sgpio is used for s sata 0 3 see the table on the right for pin defi nitions
- This serverboard has six system cpu fan headers fan 1 fan 4 fan a and fan b on the serverboard all these 4 pin fans headers are backward compatible with the traditional 3 pin fans however fan speed control is available for 4 pin fans only the fan speeds are controlled by thermal management via ipmi 2 interface see the table on the right for pin defi nitions
- Superserve
- S sgpio and i sgpio 1 2 headers
- R wc1r t user s manual
- Pwr smb pin defi nitions
- Power system management bus
- Power smb
- Ipmb header pin defi nitions
- Fan headers
- Fan header pin defi nitions
- C1 monitors power supply fan and system temperatures see the table on the right for pin defi nitions
- C connector jp
- Explanation of jumpers
- 9 jumper settings
- Superserve
- The lan ports are located on the io backplane on the serverboard each ethernet lan port has two leds the yellow led indicates activity link led located on the left side of the lan port may be green amber or off indicating the speed of the connection see the tables at right for more information
- Superserve
- R wc1r t user s manual
- Lan connection speed indicator left led settings
- Ipmi lan link speed led left activity led right
- Ipmi dedicated lan leds
- In addition to lan 1 lan 2 an ipmi dedicated lan is located on the i o backplane of the serverboard the amber led on the right indicates activity while the green led on the left indicates the speed of the connection see the tables at right for more information
- Glan leds
- Glan activity indicator right led settings
- Bmc heartbeat led states
- Bmc heartbeat led
- A bmc heartbeat led is located at ledm1 on the serverboard when ledm1 is blinking bmc functions normally see the table at right for more information
- 10 onboard led indicators
- 11 sata connections
- Superserve
- 12 installing software
- Superdoctor 5
- Superserve
- 13 serverboard battery
- Unpacking
- Precautions
- Chapter 6
- Advanced chassis setup
- 1 static sensitive devices
- System fan failure
- 3 system fans
- 2 control panel
- Hard drive installation
- Checking the airfl ow
- Accessing the drive bays
- 4 drive bay installation removal
- 5 power supply
- Power supply failure
- Starting bios setup utility
- Chapter 7
- 1 introduction
- Superserve
- Starting the setup utility
- How to change the confi guration data
- 2 main setup
- Boot feature
- 3 advanced setup confi gurations
- Superserve
- Socket 1 cpu information socket 2 cpu information
- Cpu confi guration
- Superserve
- Superserve
- Chipset confi guration
- Integrated io confi guration
- Superserve
- Qpi confi guration
- Memory confi guration
- Superserve
- South bridge
- Superserve
- Sata confi guration
- Pcie pci pnp confi guration
- Superserve
- Super io confi guration
- Sol serial_over_lan confi guration
- Com 1 confi guration
- Superserve
- Serial port console redirection
- Console redirection settings
- Superserve
- Console redirection settings
- Acpi settings
- Trusted computing available if a tpm device is installed
- Superserve
- Intel me management engine subsystem
- Change smbios event log settings
- 4 event logs
- Superserve
- System event log
- 5 ipmi
- Superserve
- Bmc network confi guration
- 6 boot
- Superserve
- 7 security
- 8 save exit
- Superserve
- X9 ipmi error codes
- These fatal errors are usually communicated through a series of audible beeps the numbers on the fatal error list on the following page correspond to the number of beeps for the corresponding error all errors listed with the exception of beep code 8 are fatal errors
- Non fatal errors are those which in most cases allow the system to continue the boot up process the error messages normally appear on the screen
- Fatal errors are those which will not allow the system to continue the boot up procedure if a fatal error occurs you should consult with your system manufacturer for possible repairs
- During the post power on self test routines which are performed each time the system is powered on errors may occur
- Bios error beep codes
- Appendix a bios error beep codes
- Appendix a
- A 1 amibios error beep codes
- Expansion slots
- Drive bays
- Chipset
- Chassis
- Appendix b
- System specifi cations
- Serverboard
- Processors
- Memory capacity
- Weight
- System cooling
- Regulatory compliance
- Power supply output
- Power supply input requirements
- Operating environment
- Erver 1027r 73dbrf user s manual
Похожие устройства
-
Supermicro SYS-7047GR-TRF, X9DRG-QF C602 Dual Xeon Socket2011 1866/1600/1333/1066/800MHz, up to 192GB DDR3 ECC Reg, 10xSATA, 1620WИнструкция по эксплуатации -
Supermicro SYS-7048R-TR, X10DRi C612 Dual Xeon Socket2011-3 2133/1866/1600MHz, up to 1TB DDR4 ECC Reg, 8xSATA3, 920W (1+1)Инструкция по эксплуатации -
Supermicro SYS-7048R-TRT, X10DRi-T C612 Dual Xeon Socket2011-3 2133/1866/1600MHz, up to 1TB DDR4 ECC Reg, 8xSATA3, 920W (1+1)Инструкция по эксплуатации -
Supermicro SYS-7047R-TRF, X9DRi-F C602 Dual Xeon Socket2011, 800-1600MHz, up to 512MB DDR3 ECC Reg, 8xSATA3, 920W (1+1)Инструкция по эксплуатации -
Supermicro SYS-5018R-МRИнструкция по эксплуатации -
Supermicro SYS-1028R-WC1RИнструкция по эксплуатации -
Supermicro SYS-1018GR-TИнструкция по эксплуатации -
Supermicro SYS-5018A-TN4Инструкция по эксплуатации -
Supermicro SYS-5019S-MN4Инструкция по эксплуатации -
Supermicro SYS-6028R-TRTИнструкция по эксплуатации -
Supermicro sys-6028r-trИнструкция по эксплуатации -
Supermicro sys-5018d-mtrfИнструкция по эксплуатации
Изучите подробные технические характеристики серверной системы, включая процессоры, память, слоты расширения и размеры шасси для оптимальной производительности.