![Janome JEM PLATINUM 760 — как использовать зигзагообразный шов для обработки тканей [24/46]](/icons/site-icon-64.png){kind=icon}
Janome JEM PLATINUM 760 — как использовать зигзагообразный шов для обработки тканей [24/46]
Превью страниц
Страница 24 /
46
![Janome JEM PLATINUM 760 [24/46] Utility stitches](/views2/1341707/page24/bg18.png)
22
Multiple Zigzag Stitch (Tricot Stitch)
This stitch is used to finish a raw edge of synthetics
and other stretch fabrics that tend to pucker.
Sew along the fabric edge leaving an adequate seam
allowance.
After sewing, trim the seam allowance close to the
stitches.
Overcasting with Zigzag Stitch
Place the fabric edge next to the right side of the
clear window of the foot and carefully guide the fabric
so the needle falls off the edge when it swings to the
right.
q Clear window
UTILITY STITCHES
q
Machine settings
q Pattern: #05
w Presser foot: Zigzag foot A
e Thread tension: 3 – 7
Machine settings
q Pattern: #10
w Presser foot: Zigzag foot A
e Thread tension: 3 – 6
Содержание
62- Warnin
- The design and specifications are subject to change without a prior notice
- Important safety instructions
- Save these instructions
- Know your machine
- Setting the spool pin
- Name of parts
- Standard accessories
- Extention table
- Warning
- Getting ready to sew
- Connecting the power supply
- Controlling sewing speed
- Function buttons
- Warning
- Dropping the feed dog
- Detaching and attaching the foot holder
- Changing the presser foot
- Raising and lowering the presser foot
- Balancing thread tension
- Needle and thread chart
- Changing needles
- Always make sure to turn the power switch off and disconnect the machine from power supply before changing the needle
- Z loosen the needle clamp screw by turning it counterclockwise remove the needle from the clamp q needle clamp screw
- X insert a new needle into the needle clamp with the flat side of the needle to the rear when inserting the needle into the needle clamp push it up against the stopper pin and tighten the needle clamp screw firmly w stopper pin e flat side
- Warning
- To check needle straightness place the flat side of the needle onto something flat a needle plate glass etc the gap between the needle and the flat surface should be consistent never use a blunt needle r gap
- Raise the needle by turning the handwheel and lower the presser foot turn off the power switch
- Winding the bobbin
- Warning
- Threading the machine
- Needle threader
- Drawing up the bobbin thread
- Straight stitch
- Basic stitches
- Variety of straight stitches and recommended feet
- Zigzag stitch
- Overcasting with zigzag stitch
- Multiple zigzag stitch tricot stitch
- Utility stitches
- Buttonholes
- Button sewing
- Zipper sewing
- Caution
- Blind hemming
- Eyelet
- Patchwork
- Decorative sewing
- Applique
- Smocking
- Scallop stitch
- Decorative satin stitches
- Fagoting
- Cross stitch
- Correcting distorted stretch patterns
- Pattern combination
- Warning
- Replacing the bobbin holder
- Cleaning the hook race and feed dogs
- Care and maintenance
- Problems and warning signals
- Troubleshooting
Похожие устройства
-
Janome TOP 14Инструкция к устройству -
Janome TOP 12Руководство по использованию
-
Janome ESCAPE V-17Руководство по эксплуатации
-
Janome S-21Инструкция по работе
-
Janome LADY 725Руководство по настройке -
Janome S-19Руководство по эксплуатации -
Janome ARTDECOR 724EРуководство по эксплуатации -
Janome ARTDECOR 724AРуководство по эксплуатации
-
Janome LEGEND LE-35Руководство по эксплуатации -
Janome ARTDECOR 718AРуководство по эксплуатации -
Janome S-17Руководство по эксплуатации
-
Janome LW 20Инструкция по эксплуатации
Узнайте, как правильно использовать зигзагообразный шов для обработки краев синтетических и эластичных тканей. Подробные инструкции и советы по настройкам машины.