![Janome JEM PLATINUM 760 — настройки швейной машины для вышивки крестом и фаготинга [41/46]](/icons/site-icon-64.png){kind=icon}
Janome JEM PLATINUM 760 — настройки швейной машины для вышивки крестом и фаготинга [41/46]
Превью страниц
Страница 41 /
46
![Janome JEM PLATINUM 760 [41/46] Fagoting](/views2/1341707/page41/bg29.png)
39
Cross Stitch
Machine setting
q Stitch pattern: #47 – #50
w Presser foot: Satin stitch F
e Thread tension: 3 – 6
Fagoting
Machine setting
q Stitch pattern: #44
w Presser foot: Zigzag foot A
e Thread tension: 3 – 6
Use this stitch to join two pieces of fabric to create an
open work appearance, and add design interest.
Fold under each fabric edge 1/2" (1.3 cm) and press.
Pin the two edges to a piece of paper or tear-away
backing 1/8" (0.3 cm) apart.
q Paper
Sew slowly, guiding the fabric so the needle catches
the folded edge on each side.
Tear away the backing after sewing is finished.
You can make cross stitch designs with these
patterns, in half the time it would take if
embroidered by hand.
* If you press the auto lock button before sewing,
the machine will sew one unit of the cross stitch
and stop automatically.
q
w
e
q
q
w
e
Содержание
62- Warnin
- The design and specifications are subject to change without a prior notice
- Important safety instructions
- Save these instructions
- Know your machine
- Setting the spool pin
- Name of parts
- Standard accessories
- Extention table
- Warning
- Getting ready to sew
- Connecting the power supply
- Controlling sewing speed
- Function buttons
- Warning
- Dropping the feed dog
- Detaching and attaching the foot holder
- Changing the presser foot
- Raising and lowering the presser foot
- Balancing thread tension
- Needle and thread chart
- Changing needles
- Always make sure to turn the power switch off and disconnect the machine from power supply before changing the needle
- Z loosen the needle clamp screw by turning it counterclockwise remove the needle from the clamp q needle clamp screw
- X insert a new needle into the needle clamp with the flat side of the needle to the rear when inserting the needle into the needle clamp push it up against the stopper pin and tighten the needle clamp screw firmly w stopper pin e flat side
- Warning
- To check needle straightness place the flat side of the needle onto something flat a needle plate glass etc the gap between the needle and the flat surface should be consistent never use a blunt needle r gap
- Raise the needle by turning the handwheel and lower the presser foot turn off the power switch
- Winding the bobbin
- Warning
- Threading the machine
- Needle threader
- Drawing up the bobbin thread
- Straight stitch
- Basic stitches
- Variety of straight stitches and recommended feet
- Zigzag stitch
- Overcasting with zigzag stitch
- Multiple zigzag stitch tricot stitch
- Utility stitches
- Buttonholes
- Button sewing
- Zipper sewing
- Caution
- Blind hemming
- Eyelet
- Patchwork
- Decorative sewing
- Applique
- Smocking
- Scallop stitch
- Decorative satin stitches
- Fagoting
- Cross stitch
- Correcting distorted stretch patterns
- Pattern combination
- Warning
- Replacing the bobbin holder
- Cleaning the hook race and feed dogs
- Care and maintenance
- Problems and warning signals
- Troubleshooting
Похожие устройства
-
Janome TOP 14Инструкция к устройству -
Janome TOP 12Руководство по использованию
-
Janome ESCAPE V-17Руководство по эксплуатации
-
Janome S-21Инструкция по работе
-
Janome LADY 725Руководство по настройке -
Janome S-19Руководство по эксплуатации -
Janome ARTDECOR 724EРуководство по эксплуатации -
Janome ARTDECOR 724AРуководство по эксплуатации
-
Janome LEGEND LE-35Руководство по эксплуатации -
Janome ARTDECOR 718AРуководство по эксплуатации -
Janome S-17Руководство по эксплуатации
-
Janome LW 20Инструкция по эксплуатации
Узнайте, как правильно настроить швейную машину для вышивки крестом и фаготинга. Подробные инструкции по выбору стежков и натяжению нити.