Janome JEM PLATINUM 760 [43/46] Warning
Превью страниц
Страница 43 /
46
![Janome JEM PLATINUM 760 [43/46] Warning](/views2/1341707/page43/bg2b.png)
41
CARE AND MAINTENANCE
WARNING:
Turn the power switch off and unplug the machine
before cleaning.
NOTE:
Do not dismantle the machine in any way other than
what is explained in this section.
Clean the outside of the machine with a soft cloth and
mild soap.
Cleaning the Hook Race and Feed Dogs
z Remove the presser foot and needle. Remove screw
on the needle plate with the screwdriver.
Remove the needle plate and take out the bobbin.
q Screw
x Lift up the bobbin holder and remove it.
w Bobbin holder
c Brush out dust and lint. Wipe the bobbin holder with
a soft, dry cloth.
v Clean the feed dogs and hook race with the lint
brush.
e Lint brush
r Feed dog
b Wipe the hook race with a soft, dry cloth.
t Hook race
NOTE:
You may also use a vacuum cleaner.
Replacing the Bobbin Holder
z Insert the bobbin holder into the hook race.
x Make sure the knob of the bobbin holder fits next to
the stopper on the race.
q Knob
w Stopper
c Replace the bobbin.
Attach the needle plate, inserting the two guide pins
into the holes in the needle plate. Tighten the screw
firmly with the screwdriver.
e Guide holes
r Screw
q
w
e
r
t
w
z
x
c
v
b
q
w
e
r
e
z
x
c
Содержание
62- Warnin
- The design and specifications are subject to change without a prior notice
- Important safety instructions
- Save these instructions
- Know your machine
- Setting the spool pin
- Name of parts
- Standard accessories
- Extention table
- Warning
- Getting ready to sew
- Connecting the power supply
- Controlling sewing speed
- Function buttons
- Warning
- Dropping the feed dog
- Detaching and attaching the foot holder
- Changing the presser foot
- Raising and lowering the presser foot
- Balancing thread tension
- Needle and thread chart
- Changing needles
- Always make sure to turn the power switch off and disconnect the machine from power supply before changing the needle
- Z loosen the needle clamp screw by turning it counterclockwise remove the needle from the clamp q needle clamp screw
- X insert a new needle into the needle clamp with the flat side of the needle to the rear when inserting the needle into the needle clamp push it up against the stopper pin and tighten the needle clamp screw firmly w stopper pin e flat side
- Warning
- To check needle straightness place the flat side of the needle onto something flat a needle plate glass etc the gap between the needle and the flat surface should be consistent never use a blunt needle r gap
- Raise the needle by turning the handwheel and lower the presser foot turn off the power switch
- Winding the bobbin
- Warning
- Threading the machine
- Needle threader
- Drawing up the bobbin thread
- Straight stitch
- Basic stitches
- Variety of straight stitches and recommended feet
- Zigzag stitch
- Overcasting with zigzag stitch
- Multiple zigzag stitch tricot stitch
- Utility stitches
- Buttonholes
- Button sewing
- Zipper sewing
- Caution
- Blind hemming
- Eyelet
- Patchwork
- Decorative sewing
- Applique
- Smocking
- Scallop stitch
- Decorative satin stitches
- Fagoting
- Cross stitch
- Correcting distorted stretch patterns
- Pattern combination
- Warning
- Replacing the bobbin holder
- Cleaning the hook race and feed dogs
- Care and maintenance
- Problems and warning signals
- Troubleshooting
Похожие устройства
-
Janome TOP 14Инструкция к устройству -
Janome TOP 12Руководство по использованию -
Janome ESCAPE V-17Руководство по эксплуатации -
Janome S-21Инструкция по работе -
Janome LADY 725Руководство по настройке -
Janome S-19Руководство по эксплуатации -
Janome ARTDECOR 724EРуководство по эксплуатации -
Janome ARTDECOR 724AРуководство по эксплуатации -
Janome LEGEND LE-35Руководство по эксплуатации -
Janome ARTDECOR 718AРуководство по эксплуатации -
Janome S-17Руководство по эксплуатации -
Janome LW 20Инструкция по эксплуатации