Janome JEM PLATINUM 760 [4/46] Know your machine
Превью страниц
Страница 4 /
46
![Janome JEM PLATINUM 760 [4/46] Know your machine](/views2/1341707/page4/bg4.png)
2
KNOW YOUR MACHINE
Name of Parts
q Direct pattern selection buttons
w Indicator window
e Bobbin winder stopper
r Bobbin winder spindle
t Spool pin (included in accessory bag)
y Bobbin winding thread guide
u Thread guide
i Thread take-up lever
o Tension regulating dial
!0 Face plate
!1 Thread cutter
!2 Needle threader
!3 Needle plate
!4 Extension table (accessory storage)
!5 Hook cover plate
!6 Hook cover plate release button
!7 Speed control slider
!8 Stitch width adjusting button
!9 Stitch length adjusting button
@0 Start/stop button
@1 Reverse button
@2 Auto-lock button
@3 Up/down needle button
@4 Foot holder
@5 Needle clamp screw
@6 Needle
@7 Zigzag foot A
@8 Carrying handle
@9 Hole for additional spool pin
#0 Hand wheel
#1 Stitch balance adjusting dial
#2 Power switch
#3 Machine socket
#4 Power inlet
#5 Drop-feed lever
#6 Free arm
#7 Buttonhole lever
#8 Presser foot lifter
#9 Reference chart
q
Setting the Spool Pin
Insert the spool pin into the hole as
shown.
(The spool pin is in the accessory bag.)
q Spool pin
w Setting hole
w
e
r
t
!9
!8
!7
#9
!6
!5
y
u
i
o
!0
!1
!2
!3
!4
@37
@27
@1
@0
@5
@6
@44
@7
#8
@8
#7
#6
#5
@9
#0
#4
#3
#2
#1
q
w
Содержание
62- Warnin
- The design and specifications are subject to change without a prior notice
- Important safety instructions
- Save these instructions
- Know your machine
- Setting the spool pin
- Name of parts
- Standard accessories
- Extention table
- Warning
- Getting ready to sew
- Connecting the power supply
- Controlling sewing speed
- Function buttons
- Warning
- Dropping the feed dog
- Detaching and attaching the foot holder
- Changing the presser foot
- Raising and lowering the presser foot
- Balancing thread tension
- Needle and thread chart
- Changing needles
- Always make sure to turn the power switch off and disconnect the machine from power supply before changing the needle
- Z loosen the needle clamp screw by turning it counterclockwise remove the needle from the clamp q needle clamp screw
- X insert a new needle into the needle clamp with the flat side of the needle to the rear when inserting the needle into the needle clamp push it up against the stopper pin and tighten the needle clamp screw firmly w stopper pin e flat side
- Warning
- To check needle straightness place the flat side of the needle onto something flat a needle plate glass etc the gap between the needle and the flat surface should be consistent never use a blunt needle r gap
- Raise the needle by turning the handwheel and lower the presser foot turn off the power switch
- Winding the bobbin
- Warning
- Threading the machine
- Needle threader
- Drawing up the bobbin thread
- Straight stitch
- Basic stitches
- Variety of straight stitches and recommended feet
- Zigzag stitch
- Overcasting with zigzag stitch
- Multiple zigzag stitch tricot stitch
- Utility stitches
- Buttonholes
- Button sewing
- Zipper sewing
- Caution
- Blind hemming
- Eyelet
- Patchwork
- Decorative sewing
- Applique
- Smocking
- Scallop stitch
- Decorative satin stitches
- Fagoting
- Cross stitch
- Correcting distorted stretch patterns
- Pattern combination
- Warning
- Replacing the bobbin holder
- Cleaning the hook race and feed dogs
- Care and maintenance
- Problems and warning signals
- Troubleshooting
Похожие устройства
-
Janome TOP 14Инструкция к устройству -
Janome TOP 12Руководство по использованию -
Janome ESCAPE V-17Руководство по эксплуатации -
Janome S-21Инструкция по работе -
Janome LADY 725Руководство по настройке -
Janome S-19Руководство по эксплуатации -
Janome ARTDECOR 724EРуководство по эксплуатации -
Janome ARTDECOR 724AРуководство по эксплуатации -
Janome LEGEND LE-35Руководство по эксплуатации -
Janome ARTDECOR 718AРуководство по эксплуатации -
Janome S-17Руководство по эксплуатации -
Janome LW 20Инструкция по эксплуатации