Home
Главная
Hotpoint-Ariston
Плиты
CX 65 SP4 R/HA
Инструкция по эксплуатации Страница: 20

Hotpoint-Ariston CX 65 SP4 R/HA [20/52] Start up and use

Start-up and use

Using the hob

Lighting the burners

For each BURNER knob there is a complete ring showing

the strength of the flame for the relevant burner.

To light one of the burners on the hob:

1. Bring a flame or gas lighter close to the burner.

2. Press the BURNER knob and turn it in an

anticlockwise direction so that it is pointing to the

maximum flame setting -.

3. Adjust the intensity of the flame to the desired level by

turning the BURNER knob in an anticlockwise direction.

This may be the minimum setting +, the maximum setting

- or any position in between the two.

If the appliance is fitted with an

electronic lighting device* (see

figure), press the BURNER

knob and turn it in an

anticlockwise direction,

towards the minimum flame

setting, until the burner is lit.

The burner may be

extinguished when the knob is released. If this occurs,

repeat the operation, holding the knob down for a

longer period of time.

 If the flame is accidentally extinguished, switch off

the burner and wait for at least 1 minute before

attempting to relight it.

If the appliance is equipped with a flame failure safety

device*, press and hold the BURNER knob for

approximately 2-3 seconds to keep the flame alight

and to activate the device.

To switch the burner off, turn the knob until it reaches

the stop position .

Practical advice on using the burners

For the burners to work in the most efficient way

possible and to save on the amount of gas consumed,

it is recommended that only pans that have a lid and a

flat base are used. They should also be suited to the

size of the burner:

 For models equipped with a reducer grid, the latter

must be used only for the auxiliary burner, when pans

with a diameter of less than 12 cm are used.

Setting the time

Press the

PROGRAMMER knob

and turn it in an

anticlockwise direction

to set the correct time.

 The clock can only be set if the oven is connected

to the electricity mains. In case of a power failure,

the PROGRAMMER will stop: the correct time will

need to be reset once the power has returned.

Using the oven

 The first time you use your appliance, heat the empty

oven with its door closed at its maximum temperature

for at least half an hour. Ensure that the room is well

ventilated before switching the oven off and opening the

oven door. The appliance may emit a slightly

unpleasant odour caused by protective substances

used during the manufacturing process burning away.

 Never put objects directly on the bottom of the oven;

this will avoid the enamel coating being damaged.

 Before operating the product, remove all plastic film

from the sides of the appliance.

1. Select the desired cooking mode by turning the

SELECTOR knob.

2. Select the recommended temperature for the

cooking mode or the desired temperature by turning

the THERMOSTAT knob.

A list detailing cooking modes and suggested

cooking temperatures can be found in the relevant

table (see Oven cooking advice table).

During cooking it is always possible to:

 Change the cooking mode by turning the

SELECTOR knob.

Only available in certain models.

To identify the type of burner, please refer to the

diagrams contained in the Burner and nozzle

specifications.

Burner ø Cookware Diameter (cm)

Fast (R) 24 - 26

Semi Fast (S) 16 - 20

Auxiliary (A) 10 - 14

Triple Crown (TC) 24 - 26

Содержание

Похожие устройства

Start up and use GB Using the hob Lighting the burners For each BURNER knob there is a complete ring showing the strength of the flame for the relevant burner To light one of the burners on the hob 1 Bring a flame or gas lighter close to the burner 2 Press the BURNER knob and turn it in an anticlockwise direction so that it is pointing to the maximum flame setting A 3 Adjust the intensity of the flame to the desired level by turning the BURNER knob in an anticlockwise direction This may be the minimum setting d the maximum setting 6 or any position in between the two If the appliance is fitted with an electronic lighting device see figure press the BURNER knob and turn it in an anticlockwise direction towards the minimum flame setting until the burner is lit The burner may be extinguished when the knob is released If this occurs repeat the operation holding the knob down for a longer period of time If the flame is accidentally extinguished switch off the burner and wait for at least 1 minute before attempting to relight it For models equipped with a reducer grid the latter must be used only for the auxiliary burner when pans with a diameter of less than 12 cm are used Setting the time Press the PROGRAMMER knob and turn it in an anticlockwise direction to set the correct time The clock can only be set if the oven is connected to the electricity mains In case of a power failure the PROGRAMMER will stop the correct time will need to be reset once the power has returned Using the oven If the appliance is equipped with a flame failure safety device press and hold the BURNER knob for approximately 2 3 seconds to keep the flame alight and to activate the device The first time you use your appliance heat the empty oven with its door closed at its maximum temperature for at least half an hour Ensure that the room is well ventilated before switching the oven off and opening the oven door The appliance may emit a slightly unpleasant odour caused by protective substances used during the manufacturing process burning away To switch the burner off turn the knob until it reaches the stop position Never put objects directly on the bottom of the oven this will avoid the enamel coating being damaged Practical advice on using the burners For the burners to work in the most efficient way possible and to save on the amount of gas consumed it is recommended that only pans that have a lid and a flat base are used They should also be suited to the size of the burner Before operating the product remove all plastic film from the sides of the appliance Burner 0 Cookware Diameter cm Fast R 24 26 Semi Fast S 16 20 Auxiliary A 10 14 Triple Crown TC 24 26 To identify the type of burner please refer to the diagrams contained in the Burner and nozzle specifications 20 1 Select the desired cooking mode by turning the SELECTOR knob 2 Select the recommended temperature for the cooking mode or the desired temperature by turning the THERMOSTAT knob A list detailing cooking modes and suggested cooking temperatures can be found in the relevant table see Oven cooking advice table During cooking it is always possible to Change the cooking mode by turning the SELECTOR knob Only available in certain models

Скачать

Случайные обсуждения

Ответы 1

Не включается нижняя плита

5 месяцев назад

Ответы 0

Снятие двери духовки

4 месяца назад