Hotpoint-Ariston CE 6V P4 R/HA [15/76] Installation h

Hotpoint-Ariston CE 6V P4 R/HA [15/76] Installation h
GB
15
Before operating your new appliance please read
this instruction booklet carefully. It contains important
information concerning the safe installation and
operation of the appliance.
Please keep these operating instructions for future
reference. Make sure that the instructions are kept with
the appliance if it is sold, given away or moved.
The appliance must be installed by a qualified
professional in accordance with the instructions
provided.
Any necessary adjustment or maintenance must be
performed after the cooker has been disconnected
from the electricity supply.
Positioning and levelling
It is possible to install the appliance alongside
cupboards whose height does not exceed that of the
hob surface.
Make sure that the wall in contact with the back of
the appliance is made from a non-flammable, heat-
resistant material (T 90°C).
To install the appliance correctly:
Place it in the kitchen, the dining room or the bed-
sit (not in the bathroom).
If the top of the hob is higher than the cupboards,
the appliance must be installed at least 600 mm
away from them.
If the cooker is
installed underneath a
wall cabinet, there must
be a minimum distance
of 420 mm between this
cabinet and the top of
the hob.
This distance should be
increased to 700 mm if
the wall cabinets are
flammable (see figure).
Do not position blinds behind the cooker or less
than 200 mm away from its sides.
Any hoods must be installed according to the
instructions listed in the relevant operating manual.
Levelling
If it is necessary to level the
appliance, screw the
adjustable feet into the places
provided on each corner of the
base of the cooker (see figure).
The legs* fit into the slots on
the underside of the base of
the cooker.
Electrical connection
Fitting the power supply cable
To open the terminal board:
Insert a screwdriver into the side tabs of the
terminal board cover.
Pull the cover to
open it.
To install the cable, follow the instructions below:
Loosen the cable clamp screw and the wire contact
screws.
The jumpers are pre-set at the Factory for 230 V
single-phase connection (see figure).
To carry out the electrical connections as shown in
the figures, use the two jumpers inside the box (see
figure - labelled P).
Installation
HOOD
420
Min.
min. 650 mm. with hood
min.
700 mm. without hood
mm.
600
Min. mm.
420
Min. mm.
*
Only available in certain models.
N
L2
L1
L3
P
NL
230V 1N~
H07RN-F 3x4 CEI-UNEL 35364
1
3
2
4
5

Содержание

Installation H Hotpoint ARISTON Before operating your new appliance please read this instruction booklet carefully It contains important information concerning the safe installation and operation of the appliance The legs fit into the slots on the underside of the base of the cooker GB Please keep these operating instructions for future reference Make sure that the instructions are kept with the appliance if it is sold given away or moved The appliance must be installed by a qualified professional in accordance with the instructions provided Any necessary adjustment or maintenance must be performed after the cooker has been disconnected from the electricity supply Electrical connection Fitting the power supply cable To open the terminal board Insert a screwdriver into the side tabs of the Pull the cover to open it Positioning and levelling It is possible to install the appliance alongside cupboards whose height does not exceed that of the hob surface Make sure that the wall in contact with the back of the appliance is made from a non flammable heatresistant material T 90 C To install the appliance correctly Place it in the kitchen the dining room or the bed sit not in the bathroom If the top of the hob is higher than the cupboards the appliance must be installed at least 600 mm away from them If the cooker is installed underneath a wall cabinet there must be a minimum distance of 420 mm between this cabinet and the top of the hob This distance should be increased to 700 mm if the wall cabinets are flammable see figure Do not position blinds behind the cooker or less than 200 mm away from its sides Any hoods must be installed according to the instructions listed in the relevant operating manual To install the cable follow the instructions below Loosen the cable clamp screw and the wire contact screws The jumpers are pre set at the Factory for 230 V single phase connection see figure 230V 1NH07RN F 3x4 CEI UNEL 35364 NL To carry out the electrical connections as shown in the figures use the two jumpers inside the box see figure labelled P Levelling If it is necessary to level the appliance screw the adjustable feet into the places provided on each corner of the base of the cooker see figure Only available in certain models 15

Скачать