Bosch GSB 36 VE-2-LI Professional [17/217] Operation
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Bosch GSB 36 VE-2-LI Professional [17/217] Operation

Bosch GSB 36 VE-2-LI Professional [17/217] Operation
English | 17
Bosch Power Tools 1 619 929 J10 | (6.4.11)
Push button 13 to indicate the charge condition (also possi-
ble when the battery is removed). The battery charge-control
indicator automatically goes out after approx. 5 seconds.
When no LED lights up after pushing button 13, then the bat-
tery is defective and must be replaced.
During the charging procedure, the three green LEDs light up
one after the other and briefly go out. The battery is fully
charged when the three green LEDs light up continuously. The
three LEDs go out again approx. 5 minutes after the battery
has been fully charged.
The battery is equipped with a NTC temperature control
which allows charging only within a temperature range of be-
tween 0 °C and 45 °C. A long battery service life is achieved
in this manner.
Auxiliary Handle (see figure B)
f Before any work on the machine (e. g., maintenance,
tool change, etc.) as well as during transport and stor-
age, set the rotational direction switch to the centre
position. Unintentional actuation of the On/Off switch can
lead to injuries.
f Operate your machine only with the auxiliary handle 7.
The auxiliary handle 7 can be set to any position for a secure
and low-fatigue working posture.
Turn the bottom part of the auxiliary handle 7 in counterclock-
wise direction and swivel the auxiliary handle 7 to the desired
position. Then retighten the bottom part of the auxiliary han-
dle 7 by turning in clockwise direction.
The clamping band 15 of the auxiliary handle must be seated
in the corresponding groove.
Changing the Tool (see figure C)
f Before any work on the machine (e. g., maintenance,
tool change, etc.) as well as during transport and stor-
age, set the rotational direction switch to the centre
position. Unintentional actuation of the On/Off switch can
lead to injuries.
The drill spindle is locked when the On/Off switch 6 is not
pressed. This makes quick, convenient and easy changing of
the tool in the drill chuck possible.
Open the keyless chuck 1 by turning in rotation direction n,
until the tool can be inserted. Insert the tool.
Firmly tighten the collar of the keyless chuck 1 by hand in ro-
tation direction o until the locking action (“click”) is no longer
heard. This automatically locks the chuck.
The locking is released again to remove the tool when the col-
lar is turned in the opposite direction.
Replacing the Drill Chuck
f Before any work on the machine (e. g., maintenance,
tool change, etc.) as well as during transport and stor-
age, set the rotational direction switch to the centre
position. Unintentional actuation of the On/Off switch can
lead to injuries.
Removing the Securing Screw (see figure D)
The keyless chuck 1 is secured with a securing screw 17
against unintentional loosening from the drill spindle. Com-
pletely open the keyless chuck 1 and unscrew the securing
screw 17 in rotation direction n. Please note that the se-
curing screw has a left-hand thread.
Removing the Drill Chuck (see figure E)
Clamp the short end of an Allen key 18 into the keyless chuck 1.
Place the machine on a stable surface (e. g. a workbench).
Hold the machine firmly and loosen the keyless chuck 1 by
turning the Allen key 18 in rotation direction n. Loosen a
tight-seated keyless chuck by giving the long end of the Allen
key 18 a light blow. Remove the Allen key from the keyless
chuck and completely unscrew the keyless chuck.
Mounting the Drill Chuck (see figure F)
The keyless chuck is mounted in reverse order.
Note: After mounting the keyless chuck, screw the securing
screw 17 in again.
The drill chuck must be tightened with a tightening
torque of approx. 10–25 Nm.
Dust/Chip Extraction
f Dusts from materials such as lead-containing coatings,
some wood types, minerals and metal can be harmful to
one’s health. Touching or breathing-in the dusts can cause
allergic reactions and/or lead to respiratory infections of
the user or bystanders.
Certain dusts, such as oak or beech dust, are considered
as carcinogenic, especially in connection with wood-treat-
ment additives (chromate, wood preservative). Materials
containing asbestos may only be worked by specialists.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the
materials to be worked.
f Prevent dust accumulation at the workplace. Dusts can
easily ignite.
Operation
Starting Operation
Inserting the Battery
f Use only original Bosch lithium ion batteries with the
voltage listed on the nameplate of your power tool.
Using other batteries can lead to injuries and pose a fire
hazard.
Set the rotational direction switch 5 to the centre position to
protect the power tool against accidental starting.
LED Capacity
Continuous lighting 3 x green ≥ 2/3
Continuous lighting 2 x green ≥ 1/3
Continuous lighting 1 x green <1/3
Flashing light 1 x green Reserve
OBJ_BUCH-487-002.book Page 17 Wednesday, April 6, 2011 8:11 AM

Содержание

Похожие устройства

OBJ BUCH 4S7 002 book Page 17 Wednesday April 6 2011 8 11 AM English 117 Push button 13 toindicate the charge condition also possi Replacing the Drill Chuck ble when thebattery is removed Thebattery charge control Beforeany work on the machine e g maintenance indicator automatically goes out after approx 5 seconds 1 LED Capacity Continuous lighting 3 x green 2 3 Continuous lighting 2 xgreen 1 3 tool change etc as well as duringtransport and stor i age set the rotational direction switch to the centre position Unintentional actuation of theOn Off switch can lead to injuries Continuous lighting 1 x green 1 3 Flashing light lx green Reserve RemovingtheSecuring Screw see figure D The keyless chuck 1 is secured with a securing screw 17 against unintentional loosening from the drill spindle Com When no LED lights up after pushing button 13 then the bat pletely open the keyless chuck 1 and unscrew the securing tery is defective and must be replaced screw 17 in rotation direction O Pleasenotethat the se During the charging procedure the three green LEDs light up one after the other and briefly go ouL The battery is fully curing screw has a left hand thread charged when the threegreen LEDs light up continuously The three LEDs go out again approx 5 minutes after the battery has been fully charged The battery is equi pped with a MTC temperature control which allows charging only within a temperature range of be tween 0 C and 45 C A long battery service life is achieved in this manner Removingthe Drill Chuck see figure E Clamp theshort end of an Allen key 18 into the keyless chuck 1 Place the machine on a stable surface e g a workbench Hold the machine firmly and loosen the keyless chuck 1 by turning the Allen key 18in rotation direction O Loosen a tight seated keyless chuck by giving the long end of the Allen key 18 a I ight blow Remove the All en key from the keyless chuck and completely unscrew the keyless chuck Auxiliary Handle see figure B Mounting the Drill Chuck see figure F Before any work on the machine e g maintenance The keyless chuck is mounted in reverse order tool change etc as well as during transport and stor age set the rotational direction switch tothe centre position Unintentional actuation of the On Off switch can lead toinjuries Note After mounting the keyless chuck screw the securing screw 17 in again A The drill chuck must be tightened witha tightening 1 torqueofapprox 10 25Nm Operate your machine only with the auxiliary handle 7 The auxiliary handle 7 can be set to any position for a secure Dust Chip Extraction andlow fatigueworkingposture Dusts from materials such as lead containing coatings some wood types minerals and metal can be harmful to Turn the bottom part of the auxiliary handle in counterclock wise direction andswivel theauxiliary handle 7 tothe desired one s health Touching or breathing in the dusts can cause position Then retighten the bottom part of the auxiliary han allergic reactions and or lead to respiratory infections of dle 7 by turning in clockwise direction the user or bystanders The clamping band 15 of the auxiliary handle must be seated Certain dusts such as oak or beech dust are considered as carcinogenic especially in connection with wood treat in the corresponding groove ment additives chromate wood preservative Materials Changing the Tool see figure C containing asbestos may only be worked by specialists Before any work on the machine e g maintenance tool change etc as well as during transport and stor Provide for good ventil ation of the working place age set the rotational direction switch tothe centre position Unintentional actuation of the On Off switch can lead toinjuries The drill spindle is locked when the On Off switch 6 is not pressed This makes quick convenient and easy changing of the tool in the drill chuck possible It is recommended towear a P2 filter class respirator Observe the relevant regulations in your country for the materials to be worked Prevent dust accumulation at the workplace Dusts can easily ignite Operation Open the keyless chuck 1 by turning in rotation direction O until the tool can be inserted Insert the tool Starting Operation Firmly tighten the collar of the keyless chuck 1 by hand in ro Inserting the Battery tation direction until the locking action click isno longer heard This automatically locks the chuck Use only original Bosch lithium ion batteries with the The locking is released again to remove the tool when the col lar is turned in the opposite direction voltage listed on the nameplate of your power tool Using other batteries can lead to injuries and pose a fire hazard Set the rotational direction switch 5 to the centre position to protect the power tool against accidental starting Bosch Power Tools 1619 929 J10I 6 4 11

Скачать