McCulloch 22 LCS [17/618] Carburettor
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

McCulloch 22 LCS [17/618] Carburettor

McCulloch 22 LCS [17/618] Carburettor
MAINTENANCE
English – 17
Carburettor
Adjustment of the idle speed
Before any adjustments are made, make sure that the air
filter is clean and the air filter cover is fitted.
Adjust the idle speed using the idle adjustment screw T, if
it is necessary to readjust. First turn the idle adjustment
screw T clockwise until the cutting attachment starts to
rotate. Then turn the screw anticlockwise until the cutting
attachment stops. The idle speed is correctly adjusted
when the engine will run smoothly in every position. The
idle speed should also be well below the speed at which
the cutting attachment starts to rotate.
Rec. idle speed: See the Technical data section.
Muffler
CAUTION! Some mufflers are fitted with a catalytic
converter. See chapter on Technical data to see whether
your machine is fitted with a catalytic converter.
The muffler is designed to reduce the noise level and to
direct the exhaust gases away from the operator. The
exhaust gases are hot and can contain sparks, which may
cause fire if directed against dry and combustible
material.
Some mufflers are equipped with a special spark arrestor
mesh. If your machine has this type of muffler, you should
clean the mesh at least once a week. This is best done
with a wire brush. On mufflers without a catalytic
converter the mesh should be cleaned weekly, or
replaced if necessary. On mufflers fitted with a catalytic
converter the mesh should be checked, and if necessary
cleaned, monthly. If the mesh is damaged it should be
replaced. If the mesh is frequently blocked, this can be a
sign that the performance of the catalytic converter is
impaired. Contact your dealer to inspect the muffler. A
blocked mesh will cause the machine to overheat and
result in damage to the cylinder and piston.
CAUTION! Never use a machine with a defective muffler.
!
WARNING! If the idle speed cannot be
adjusted so that the cutting attachment
stops, contact your dealer/service
workshop. Do not use the machine until
it has been correctly adjusted or
repaired.
!
WARNING! Mufflers fitted with catalytic
converters get very hot during use and
remain so for some time after stopping.
This also applies at idle speed. Contact
can result in burns to the skin.
Remember the risk of fire!

Содержание

Похожие устройства

MAINTENANCE Carburettor Adjustment of the idle speed Before any adjustments are made make sure that the air filter is clean and the air filter cover is fitted The muffler is designed to reduce the noise level and to direct the exhaust gases away from the operator The exhaust gases are hot and can contain sparks which may cause fire if directed against dry and combustible material Adjust the id Ie speed using the idle adjustment screw T if it is necessary to readjust First turn the idle adjustment screw T clockwise until the cutting attachment starts to rotate Then turn the screw anticlockwise until the cutting attachment stops The idle speed is correctly adjusted when the engine will run smoothly in every position The idle speed should also be well below the speed at which the cutting attachment starts to rotate Rec Idle speed See the Technical data section WARNING If the Idle speed cannot be adjusted so that the cutting attachment stops contact your dealer service workshop Do not use the machine until it has been correctly adjusted or repaired Some mufflers are equipped with a special spark arrestor mesh If your machine has this type of muffler you should clean the mesh at least once a week This is best done with a wire brush On mufflers without a catalytic converter the mesh should be cleaned weekly or replaced if necessary On mufflers fitted with a catalytic converter the mesh should be checked and if necessary cleaned monthly If the mesh Is damaged It should be replaced If the mesh is frequently blocked this can be a sign that the performance of the catalytic converter is impaired Contact your dealer to inspect the muffler A blocked mesh will cause the machine to overheat and result in damage to the cylinder and piston Muffler CAUTION Some mufflers are fitted with a catalytic converter See chapter on Technical data to see whether your machine is fitted with a catalytic converter CAUTION Never usea machine with a defective muffler WARNING Mufflers fitted with catalytic converters get very hot during use and remain so for some time after stopping This also applies at idle speed Contact can result in bums to the skin Remember the risk of fire English 17

Скачать