Home
Главная
Vitek
Кухонные Комбайны
VT-1616 PR
Инструкция по эксплуатации Страница: 7

Vitek VT-1616 PR [7/48] English

ENGLISH

Blender bowl

1. Turn the blender drive protecting cap (1)

clockwise and remove it.

2. Place the bowl (10) on the processor. Atten-

tion, the bowl (10) should be empty.

3. Turn the cap (16) anticlockwise up to the

stop.

4. Unite the marks on the bowl and the housing

of the blender (23), and turn the blender bowl

anticlockwise up to the stop.

5. Put some foodstuff into the blender bowl

(23).

6. Cover the blender bowl (23) with the cap (24)

and turn it anticlockwise to unite the marks

on the cap (24) and the handle of the blender

bowl (23).

7. Insert the power cord plug into the wall out-

let.

8. Turn the knob (3) to switch the processor on

and set the rotating speed “Max”, or turn on

pulse operating mode by pressing the button

“PULSE” (4).

9. You can add the necessary ingredients

through the opening blocked with the dis-

pensing tap (25) while the blender is operat-

ing. The dispensing tap (25) may be utilized

as the measuring glass. The maximum ca-

pacity of the tap is 60 ml.

10. After finishing food processing switch the

appliance off by turning the knob (3) to the

“OFF” position, and disconnect the power

cord plug from the wall outlet.

11. Turn the blender bowl (23) clockwise to re-

move it.

12. Pour the mixed up foodstuff out of the blender

bowl.

Attention!

- If the cap of the bowl (16) is not installed or

installed improperly, the blender would not be

switched on.

- If the cap of the blender bowl (24) is not in-

stalled or installed improperly, the blender

would not be switched on.

- No any nozzles should be inside the blender

bowl (10) during the operation.

- Do not pour into the blender bowl (23) more

then 1000 ml of the liquid to avoid overflowing.

- Start processing the soft vegetables or fruits

(banana, for example) in the blender bowl at

the low speed, afterwards increase the speed

gradually.

- Start processing hard vegetables and fruits

(potatoes, for example) at the highest speed.

- Do not place more then 300 g of the hard veg-

etables into the blender per one session.

- The time of the blender operation should now

exceed 20-30 seconds. The break between

the consequent sessions should be at least 2

minutes.

Cleaning the processor

• After finishing the foodstuff processing and

before cleaning always turn off the appliance

and unplug the power cord from the wall out-

let.

• It is recommended to wash the detachable

components by warm water with neutral deter-

gent. Also you can use a dishwasher for clean-

ing the metal knives.

• Wipe the housing of the processor with the soft

damp cloth. Do not use a stiff sponge, abrasive

or aggressive detergent, and dissolvent also.

• Do not immense the processor housing into

the water. Do not wash the appliance under

the water jet.

• Cleaning the blender:

- Install the blender bowl into its position, and fill

it with the warm water with neutral detergent.

- Cover the blender bowl by the cap.

- Turn the blender on for about 20 seconds by

pressing the button “PULSE”. Repeat the pro-

cedure if required. Detach the blender bowl

and wash it by warm water.

Storage

• Make sure the processor is disconnected from

the wall outlet before putting it in the storage.

• Follow the instructions of the section “Clean-

ing the processor”.

• Use the compartment (2) to store the gratings,

choppers and knives for cutting potatoes for

frying.

Attention! The cutting blades of the knives

are very sharp and dangerous, handle the

knives carefully!

• Store the appliance in the clean and dry

place.

Examples of food processing

The time of processing enlisted below is approxi-

mate. It depends on the quality of the foodstuff

and the type of the grinding (fine, normal, or

rough).

1616new.indd 71616new.indd 7 18.07.2008 12:19:3518.07.2008 12:19:35

Vitek VT-1616 PR [7/48] English

Содержание

Похожие устройства