Home
Главная
Bosch
Аккумуляторный Универсальный Резак
GOP 10,8 V-LI 0.601.858.00C
Инструкция по эксплуатации Страница: 16

Bosch GOP 10,8 V-LI 0.601.858.00C Инструкция по эксплуатации онлайн [16/196] 571

16 | English

2 609 140 809 | (25.3.11) Bosch Power Tools

Selecting the Application Tool/Accessory

Mounting/Replacing the Application Tool/Accessory

If required, remove an already mounted application tool/ac-

cessory.

For removing the application tool/accessory, loosen the

screw 11 with the Allen key 12 and remove the application

tool/accessory.

Mount the requested application tool/accessory (e.g. plunge

cut saw blade 10) in such a manner on the tool holder 8 that

the offset faces downward (see illustration on the graphics

page; marking on the application tool/accessory is readable

from above).

Turn the application tool/accessory to a position favourable

for the respective job, and allow it to engage into the cams of

the tool holder 8. 12 different positions are possible, each

offset by 30°.

For more intermediate positions, the adapter 13 (accessory)

can be used: Allow the adapter to engage with the smooth

side onto the cams of the tool holder 8 (see illustration on the

graphics page). Position the application tool/accessory onto

the adapter in any position.

Fasten the application tool/accessory with bolt 11. Tighten

the bolt with Allen key 12 until the spring washer of the bolt

faces flush against the application tool/accessory.

f Check the tight seating of the application tool/acces-

sory. Incorrect or not securely fastened application tools/

accessories can come loose during operation and pose a

hazard.

Mounting/Replacing a Sanding Sheet on the

Sanding Plate

The sanding plate 14 is fitted with Velcro backing for quick

and easy fastening of sanding sheets with Velcro adhesion.

Before attaching the sanding sheet 15, free the Velcro back-

ing of the sanding plate 14 from any debris by tapping against

it in order to enable optimum adhesion.

Position the sanding sheet 15 flush alongside one edge of the

sanding plate 14, then lay the sanding sheet onto the sanding

plate and press firmly.

To ensure optimum dust extraction, pay attention that the

punched holes in the sanding sheet match with the holes in

the sanding plate.

To remove the sanding sheet 15, grasp it at one of the tips and

pull it off from the sanding plate 14.

You can use all sanding sheets, fleece pads/polishing cloth

pads of the Delta 93 mm series of Bosch accessory program.

Sanding accessories, such as fleece pads/polishing cloth

pads, are attached to the sanding plate in the same manner.

Dust/Chip Extraction

f Dusts from materials such as lead-containing coatings,

some wood types, minerals and metal can be harmful to

one’s health. Touching or breathing-in the dusts can cause

allergic reactions and/or lead to respiratory infections of

the user or bystanders.

Certain dusts, such as oak or beech dust, are considered

as carcinogenic, especially in connection with wood-treat-

ment additives (chromate, wood preservative). Materials

containing asbestos may only be worked by specialists.

– As far as possible, use a dust extraction system suitable

for the material.

– Provide for good ventilation of the working place.

– It is recommended to wear a P2 filter-class respirator.

Observe the relevant regulations in your country for the

materials to be worked.

f Prevent dust accumulation at the workplace. Dusts can

easily ignite.

Connecting the Dust Extraction (see figure A)

For sanding, always connect dust extraction.

Remove the application tool/accessory when mounting the

dust extraction 19 (accessory).

If required, assemble the parts of the dust extraction 19 as

shown in the figure. Position the assembled dust extraction

Accessory Material

HCS wood seg-

ment saw blade*

Wooden materials,

plastic

BIM segment saw

blade*

Wooden materials,

plastic, non-ferrous

metals

HCS plunge cut

saw blades,

wood*

Wooden materials,

plastic, gypsum

and other soft

materials

BIM plunge cut

saw blades,

metal*

Metal (e.g. unhard-

ened nails, screws,

smaller profiles),

non-ferrous metals

BIM plunge cut

saw blade, wood

and metal*

Wood, metal, non-

ferrous metals

HM-Riff segment

saw blade*

Grouting joints,

soft wall tiles,

glass-fibre reinforc-

es plastic and other

abrasive materials

HM-Riff delta

plate*

Scraper, rigid* Carpets, coverings

Scraper, flexible* Silicone and other

elastic materials

Base plate for

sanding, series

Delta 93 mm*

Depends on sand-

ing sheet

* Optional accessory; for the complete accessories please see Bosch

accessory programme.

OBJ_BUCH-630-006.book Page 16 Friday, March 25, 2011 10:17 AM

Содержание

Похожие устройства

161 English Selecting the Application Tool Accessory Accessory For more intermediate positions the adapter 13 accessory Material can be used Allow the adapter to engage with the smooth side onto the cams of the tool holder 8 see illustration on the HCSwoodseg Wooden materials graphics page Position the application tool accessory onto mentsaw blade plastic the adapter in any position BIMsegmentsaw Wooden materials blade plastic non ferrous Fasten the application tool accessory with bolt 11 Tighten metals the bolt with Allen key 12 until the spring washer of the bolt faces flush against the application tool accessory HCS plunge cut Wooden materials Check the tight seating of theapplication tool acces saw blades plastic gypsum sory Incorrector not securely fastened application tools wood and other soft accessories can come loose during operation and pose a hazard materials Bl M plunge cut Metal e g unhard saw blades metal ened nails screws smaller profiles non ferrous metals Bl M plunge cut Wood metal non saw blade wood ferrous metals and metal Mounting Replacing a Sanding Sheet on the Sanding Plate The sandi ng pl ate 14 is fl tted wi th Velcro backing for qui ck and easy fastening of sanding sheets with Velcro adhesion Before attaching the sanding sheet 15 free the Velcro back ing of the sanding pl ate 14 from any debris by tappi ng agai nst it in order to enable optimum adhesion HM Riffsegment Groutingjoints Position the sanding sheet 15 flush alongside one edge of the sawblade soft wall tiles sanding plate 14 then lay the sanding sheet onto the sanding glass fibre reinforcHM Riff delta plate esplasticand other abrasive materials plate and press firmly To ensure optimum dust extraction pay attention that the punched holes in the sanding sheet match with the holes in the sanding plate To remove thesandingsheet 15 graspitatoneofthe tips and Scraper rigid Carpets coverings pull it off from thesanding plate 14 You can use all sanding sheets fleece pads polis hi ng cloth pads of the Delta 93 mm series of Bosch accessory program Sanding accessories such as fleece pads polishing cloth Scraper flexible Silicone and other elastic materials pads are attached to the sanding plate in the same manner Du st Chip Extraction Dusts from materials such as lead containing coatings some wood types mineralsand metal can be harmful to Base plate for Depends on sand sanding series ing sheet Delta 93 mm one s health Touching or breathing in thedusts can cause allergic reactions and or lead to respiratory infections of the user or bystanders Certain dusts such as oak or beech dust are considered Optional accessory tor the complete accessories please see Bosch accessory programme as carcinogenic especially in connection with wood treat ment additives chromate wood preservative Materials containingasbestosmayonlybeworkedbyspecialists Mounting Replacing the Application Tool Accessory As far as possible usea dust extraction system suitable If required remove an already mounted application tool accessory Provide for good ventilation of the working place For removing the application tool accessory loosen the Itis recommended to wear a P2 filter class respirator screw 11 wi th the Al len key 12 and remove the appli cation Observe the relevant regulations in your country for the tool accessory for the material materials to be worked Mount the requested application tool accessory e g plunge Prevent dust accumulationat the workplace Dusts can cut saw blade 10 in such a manner on the tool holder 8 that the offset faces downward see illustration on the graphics Connectingthe Dust Extraction see figure A page marking on the application tool accessory is readable from above Turn the application tool accessory toa position favourable for the respective job and allow it to engage into the cams of the tool holder 8 12 different positions are possible each offset by 30 2609140 8091 25 3 11 easily ignite For sanding always connect dust extraction Remove the application tool accessory when mounting the dust extraction 19 accessory If required assemble the parts of the dust extraction 19 as shown in the figure Position the assembled dust extraction Bosch PowerTools

Скачать