Mipro ACT82 [8/11] Digital diversity receiver digital diversity receiver

Содержание

• Act 81 act 82 1
• Electronics co ltd 1
• Instruction manual 1
• True digital wireless receiver 1
• Batteries nicad cells containing toxins are marked by accompanying symbols that refer to the prohibition of disposal with domestic waste the designations for the decisive heavy metals are cd cadmium hg mercury pb lead you may return spent batteries accumulators free of charge to the recycling centres our outlets or anywhere else where batteries accumulators are sold 2
• Disposal 2
• Important safety instruction 2
• Warning 2
• Cautions 3
• Contents digital diversity receiver 3
• Front panel operation 3
• Installation of the receiver 3
• Key features 3
• Overview 3
• Part names and functions 3
• Pc network operation 3
• Receiver operating procedures 3
• Digital diversity receiver digital diversity receiver 4
• Front panel 4
• Mipro s proprietary act function operation 4
• Part names and functions 4
• A ac power operation connect the ac power cable to the ac input jack 24 then plug 5
• A balanced output switch 4 levels of output sensitivity are available 5
• B dc power operation connect the output end of ac dc power supply to dc 12v input 5
• Digital diversity receiver digital diversity receiver 5
• Installation of the receiver 5
• Jack 22 then plug the power supply unit into an appropriate ac outlet as shown in fig 5 caution be sure the power supply is connected to an ac outlet with the correct voltage and rating 5
• Odb 10db 20db 30db select the proper output sensitivity to work with your mixers or amplifiers odb is the highest output level if distortion is experienced adjust the level counterclockwise to a lower rating until the desired output is attained 5
• Rear panel 5
• The other end into an ac outlet having the correct voltage and rating as shown in fig 4 5
• All information displays on the same vfd screen 6
• Digital diversity receiver digital diversity receiver 6
• Front panel vfd display 6
• Full lit vfd panel 6
• Receiver operating procedures 6
• Digital diversity receiver digital diversity receiver 7
• Function selection 7
• Tlt r ln lt lt r n r tn r n 7
• Digital diversity receiver digital diversity receiver 8
• Digital diversity receiver digital diversity receiver 9
• To lock display 9
• To unlock display 9
• Digital diversity receiver digital diversity receiver 10
• Pc network operation 10
• Cautions 11
• Digital diversity receiver 11

Похожие устройства

• AXIOMET AX-T02 Расширенная инструкция
• AXIOMET AX-T02 Инструкция
• AXIOMET AX-T03 Инструкция
• AXIOMET AX-T03 Расширенная инструкция
• Mipro ACT8H Инструкция по эксплуатации
• AXIOMET AX-T01 Расширенная инструкция
• AXIOMET AX-T01 Инструкция
• Mipro ACT8T Инструкция по эксплуатации
• Mipro AD-808 Инструкция по эксплуатации
• AXIOMET AX-TI220 Инструкция
• AXIOMET AX-TI220 Расширенная инструкция
• AXIOMET AX-T2400 Инструкция
• AXIOMET AX-T2400 Расширенная инструкция
• AXIOMET AX-T2200 Инструкция
• AXIOMET AX-T2200 Расширенная инструкция
• AXIOMET AX-T903 Расширенная инструкция
• AXIOMET AX-T903 Инструкция
• AXIOMET AX-T902 Расширенная инструкция
• AXIOMET AX-T902 Инструкция
• AXIOMET AX-T901 Расширенная инструкция

Digital Diversity Receiver 4 ANT Setup and Change of Antenna Status Digital Diversity Receiver 6 ADD Setup and Change of PC Address and Remote Control Frame of ADD indicator starts flashing Q PUSH FOR MODE Q PUSH FOR MODE ACT Rotate the knob to select from one of three options of antenna reception Turn clockwise to change ADD in increasing manner from 1 64 Turn counterclockwise to change EQ setting in decreasing manner from 64 1 A Operating Procedure a Press the rotary knob 8 or 11 to change to the antenna parameter When the ANT frame flashes the antenna is ready for setup b Rotate the knob 8 or 11 in a clockwise direction to select either antenna A or antenna B or a combination of both antennas as illustrated below Push knob again to set the selection Antenna A Antenna B Auto A Operating Procedure a This receiver is equipped with an ACT BUS interface It allows users to use the MIPRO DV interface converter and software sold separately with MIPRO DV for remote PC monitoring It can monitor up to a maximum of 64 channels at the same time b The receiver module address can be set up from 01 to 64 In order to monitor the system remotely each channel must have its own address for individual identification If two or more channels have been assigned to the same address it will cause confusion in the monitoring system If the system is not under PC monitoring repeated addresses will not effect the receivers operation c Switching between antenna A and B is to provide system to receive signals by one antenna This is to provide installation engineer to make proper judgement on antenna installation Hence after installation is completed system should switch back to Auto mode so the system can be full diversity and eliminate interferences c Press the rotary knob 8 or 11 to change to the ADD address parameter When ADD starts flashing the address is ready for setup d Rotate the knob 8 or 11 in a clockwise direction to choose a higher number counterclockwise to select a lower number Press knob again to set the selected ADD 5 EQ Setup and Change of Equalizer Turn clockwise to change EQ setting in increasing manner from 1 9 Turn counterclockwise to change EQ setting in decreasing manner from 9 1 A Operating Procedure a a Press the rotary knob 8 or 11 to change to the EQ parameter When the EQ frame flashes the equalizer is ready for setup b Rotate the knob 8 or 11 in a clockwise direction to choose a higher number counterclockwise to select a lower number Press knob again to set the selected EQ NOTE There are 10 preset EQ s 00 09 and EQ 09 is the only programmable EQ setting Therefore when uploading new EQ parameters from PC to receiver it will be stored in EQ 09 in the receiver 10 11