![Daikin EUWA15HDW15 [6/18] Power supply connection and crankcase heating](/img/pdf.png)
Daikin EUWA15HDW15 [6/18] Power supply connection and crankcase heating
![Daikin EUWA30HDW15 [6/18] Power supply connection and crankcase heating](/views2/1680861/page6/bg6.png)
5
BEFORE OPERATION
Checks before initial start-up
Make sure that the circuit breaker on the power supply
panel of the unit is switched off.
After the installation of the unit, check the following before switching
on the circuit breaker:
1. Field wiring
Make sure that the field wiring between the local supply panel
and the unit has been carried out according to the instructions
described in the installation manual, according to the wiring
diagrams and according to European and national regulations.
2. Additional interlock contact
An additional interlock contact S11L should be provided (e.g.
flow switch, contact of pump motor contactor). Make sure that
it has been installed between the appropriate terminals (refer
to the wiring diagram supplied with the unit). S11L should be a
normal open contact.
3. Fuses or protection devices
Check that the fuses or the locally installed protection devices
are of the size and type specified in the installation manual.
Make sure that neither a fuse nor a protection device has been
bypassed.
4. Earth wiring
Make sure that the earth wires have been connected properly
and that the earth terminals are tightened.
5. Internal wiring
Visually check the switch boxes on loose connections or
damaged electrical components.
6. Fixation
Check that the unit is properly fixed, to avoid abnormal noises
and vibrations when starting up the unit.
7. Damaged equipment
Check the inside of the unit on damaged components or
squeezed pipes.
8. Refrigerant leak
Check the inside of the unit on refrigerant leakage. If there is a
refrigerant leak, call your local Daikin dealer.
9. Oil leak
Check the compressor on oil leakage. If there is an oil leak, call
your local Daikin dealer.
10. Air inlet/outlet
Check that the air inlet and outlet of the unit is not obstructed
by paper sheets, cardboard, or any other material.
11. Power supply voltage
Check the power supply voltage on the local supply panel. The
voltage should correspond to the voltage on the identification
label of the unit.
Water supply
Fill the water piping, taking into account the minimum water volume
required by the unit. Refer to the "installation manual".
Make sure that the water is of the quality as mentioned in the
installation manual.
Purge the air at the high points of the system and check the
operation of the circulation pump and the flow switch.
Power supply connection and crankcase heating
In order to avoid compressor damage, it is necessary to
switch on the crankcase heater for at least six hours
before starting the compressor after a long period of
standstill.
To switch on the crankcase heater proceed as follows:
1. Switch on the circuit breaker on the local supply panel. Make
sure that the unit is “OFF”.
2. The crankcase heater is switched on automatically.
3. Check the supply voltage on the supply terminals L1, L2, L3,
(N) by means of a voltmeter. The voltage should correspond to
the voltage indicated on the identification label of the unit. If the
voltmeter reads values which are not within the ranges
specified in the technical data, check the field wiring and
replace the supply cables if necessary.
4. Check the LED on the reverse phase protector. If it lights up,
the phase order is correct. If not, switch off the circuit breaker
and call a licensed electrician to connect the wires of the power
supply cable in the correct phase order.
After six hours, the unit is ready for operation.
General recommendations
Before switching on the unit, read following recommendations:
1. When the complete installation and all necessary settings have
been carried out, close all front panels of the unit.
2. The service panels of the switch boxes may only be opened by
a licensed electrician for maintenance purposes.
Содержание
- Operation manual 1
- Packaged air cooled water chillers 1
- Electrical specifications 1 2
- Ntroduction 2
- Ontents 2
- Operation manual 2
- Technical specifications 1 2
- Escription 3
- Euwa20 3
- Euwa25 3
- Function of the main components 4
- Safety devices 4
- Internal wiring parts table 5
- Measuring devices 5
- Checks before initial start up 6
- Efore operation 6
- General recommendations 6
- Power supply connection and crankcase heating 6
- Water supply 6
- Digital controller 7
- Peration 7
- Working with the unit 7
- Adjusting the temperature setpoint 8
- Consulting actual operational information 8
- Enter the readout menu using the a key 8
- Enter the setpoints menu using the z key 8
- If the manual control mode is selected refer to the user settings menu none of the above mentioned setpoints will be active 8
- If the remote on off control parameter is set to no 8
- If the remote on off control parameter is set to yes 8
- If the unit does not start after a few minutes consult the readout menu which gives the status of the different circuits refer to paragraph consulting actual operational information also refer to the chapter trouble shooting 8
- Press j to save the adjusted temperature setpoint or press the z key to cancel the modification 8
- Press the f key on the controller 8
- Press the f key on the controller or switch the unit off using the remote on off switch 8
- Press the h key to adjust the temperature setting 8
- Press the w key to return successively to the second and the first screen of the readout menu 8
- Press the x key to enter the second screen of the readout menu 8
- Press the x key to enter the third screen of the readout menu 8
- Select the setpoint to be adjusted using the j key 8
- Setp cool 1 inlet water temperature cooling setpoint 1 8
- Setp cool 2 inlet water temperature cooling setpoint 2 8
- Switching the unit off 8
- The pressures measured will vary between a maximum and minimum value depending on the water and outdoor temperatures at the moment of measurement 8
- The selection between setpoint 1 and 2 is done by a remote dual setpoint switch to be installed by the customer the actual active setpoint can be consulted in the readout menu 8
- The unit provides definition and selection of two independent temperature setpoints for cooling operation 8
- To adjust a setpoint proceed as follows 8
- To adjust other setpoints repeat from instruction 2 onwards 8
- Advanced features of the digital controller 9
- History menu t t t t t 10
- Info menu y y y y y 10
- Input output menu u u u u u 10
- Safeties menu g g g g g 10
- The history menu contains all the information concerning the latest shutdowns 10
- The input output menu gives the status of all the digital inputs and the relay outputs of the unit 10
- The safeties menu provides useful information for trouble shooting purposes 10
- Timers menu r r r r r 10
- To calibrate the sensor for inlet water temperature measurement 10
- To change the user password 10
- To check the actual value of the compressor timers 10
- To check the actual value of the general software timers 10
- To check the status of circuit 1 at activation of one of the circuits safeties 10
- To check the status of circuit 2 at activation of one of the circuits safeties 10
- To check the status of circuit 3 at activation of one of the circuits safeties 10
- To check the status of the alarm the operation and the pump voltage free contacts 10
- To check the status of the circuit safeties 10
- To check the status of the evaporator heater however the evaporator heater option is not offered by daikin 10
- To check the status of the fanspeed relays 10
- To check the status of the flowswitch 10
- To check the status of the low pressure bypass switches 10
- To check the status of the remote setpoint selection switch the remote on off switch and the reverse phase protector 10
- To check whether or not the different compressors are activated 10
- To consult additional information about the unit such as the unit name the refrigerant used and the manufacturing number 10
- To consult information about the controller s software version 10
- To consult information about the number of circuit 1 shutdowns and the circuit status at the most recent shutdown 10
- To consult information about the number of circuit 2 shutdowns and the circuit status at the most recent shutdown 10
- To consult information about the number of circuit 3 shutdowns and the circuit status at the most recent shutdown 10
- To consult information about the number of shutdowns the unit safety which caused the most recent shutdown and the unit status at this shutdown 10
- To consult information about the unit safety which caused the shutdown and to check the unit status at shutdown 10
- To consult the outlet water inlet water and ambient temperature limits 10
- To define whether or not a password is needed to change the temperature setpoint 10
- User password menu q q q q q 10
- When automatic control mode is selected the unit uses default a 2 step thermostat to control the cooling load however the thermostat parameters are not fixed and can be modified via the thermostat settings screen of the user settings menu 11
- Rouble shooting 14
- Aintenance 17
- Disposal requirements 17
- Maintenance activities 17
- Thermostat parameters 17
- Pwen09719 1b 18
Похожие устройства
- Daikin EUWA15HDW15 Инструкция по монтажу
- Daikin EUWA20HDW15 Инструкция по эксплуатации
- Daikin EUWA20HDW15 Инструкция по монтажу
- Daikin EUWA25HDW15 Инструкция по эксплуатации
- Daikin EUWA25HDW15 Инструкция по монтажу
- Daikin EUWA30HDW15 Инструкция по эксплуатации
- Daikin EUWA30HDW15 Инструкция по монтажу
- Daikin EUWA5HDW1 Инструкция по монтажу
- Daikin EUWA8HDW1 Инструкция по монтажу
- Daikin EUWA10HDW1 Инструкция по монтажу
- Daikin EUWA15HDW1 Инструкция по монтажу
- Daikin EUWA20HDW1 Инструкция по монтажу
- Daikin EUWA25HDW1 Инструкция по монтажу
- Daikin EUWA30HDW1 Инструкция по монтажу
- Daikin EWAQ009ACV3 Инструкция по монтажу
- Daikin EWAQ009ACV3 Технические данные
- Daikin EWAQ010ACV3 Инструкция по монтажу
- Daikin EWAQ010ACV3 Технические данные
- Daikin EWAQ011ACV3 Технические данные
- Daikin EWAQ011ACV3 Инструкция по монтажу