![Icom IC-W32A [37/48] I pocket beep operation](/img/pdf.png)
Icom IC-W32A [37/48] I pocket beep operation
![Icom IC-W32A [37/48] I pocket beep operation](/views2/1074461/page37/bg25.png)
9
SUBAUDIBLE TONE OPERATION
33
■ Tone scan
The transceiver can detect the subaudible tone frequency in a
received signal. By monitoring a signal that is being transmit-
ted on a repeater input frequency, you can determine the tone
frequency required to access the repeater.
q Assign the main band to the desired display with [MAIN].
w Set the desired frequency or memory channel to be
checked for a tone frequency.
e Push [
(#)TSCAN] for 2 sec. to start the tone scan.
•To change the scanning direction, rotate [DIAL].
r When the tone frequency is decoded, the set mode con-
tents are programmed with the tone frequency.
•The tone scan pauses when a tone frequency is detected.
•The decoded tone frequency is used for the tone encoder or tone
encoder/decoder, depending on the the tone squelch ON/OFF
setting.
•“CT” or “RT” appears during tone scan when the tone squelch is
in use or not.
t Push [VFO] to stop the scan.
■ Pocket beep operation
This function uses subaudible tones for calling and can be
used as a “common pager” to inform you that someone has
called while you were away from the transceiver.
D Waiting for a call from a specific station
q Assign the main band to the desired display with [MAIN].
w Set the operating frequency.
e Set the desired CTCSS tone in set mode.
•See the opposite page for a list of available tone frequencies and
programming information.
r Push [TONE] several times until “ TSQLS” appears in
the function display.
t When a signal with the correct tone is received, the trans-
ceiver emits beep tones for 30 sec. and flashes
“ TSQLS.”
y Push [PTT] to answer or push [
(VFO)CLR] to stop the beeps
and flashing.
•Tone squelch is automatically selected.
D Calling a waiting station using pocket beep
A subaudible tone matched with the station’s tone frequency
is necessary. Use the tone squelch on the opposite page or a
subaudible tone encoder.
MAIN
T
“RT” or “CT” appears
during tone scan
Subaudible tone
frequencies flash as
they are scanned.
Содержание
- Dual band fm transceiver 1
- Ic w32a ic w32e 1
- Instruction manual 1
- Cautions 2
- Explicit definitions 2
- Important 2
- R warning never 2
- Read all instruction 2
- Save this instruction manual 2
- Do not 3
- Unpacking 3
- Table of contents 4
- I switches controls keys and connectors 5
- Panel description 5
- Panel description 6
- Panel description 7
- Panel description 8
- Caution 9
- Panel description 9
- I function display 10
- Main main 10
- Panel description 11
- Battery packs and accessories 12
- D battery pack life 12
- D operating period 12
- D recycling information 12
- I about the battery pack 12
- I battery pack charging 12
- I charging precautions 12
- Attach the supplied or optional battery pack then connect the supplied wall charger via an ac outlet as shown below 13
- Battery packs and accessories 13
- D rapid charging with the bc 119 13
- D regular charging 13
- I charging connections 13
- Q insert the ad 51a into the charging slot of the bc 119 13
- W insert the ad 51b into the groove in the ad 51a front fac ing side of the ad 51a observing the proper orientation e insert the battery pack either by itself or attached to the transceiver into the ad 51a 13
- Battery packs and accessories 14
- Caution remove dry cell batteries from the bp 170 14
- Connect an optional charger or cable to the transceiver as il lustrated below be careful of battery overcharging as the con nected battery is charged simultaneously 14
- D operation with an optional cable 14
- I battery case 14
- When using a battery case attached to the transceiver install 4 aa r6 size alkaline batteries as illustrated below 14
- When using the dc13 v jack 14
- Battery packs and accessories 15
- Caution 15
- D antenna 15
- D belt clip 15
- D handstrap 15
- I accessory attachment 15
- Frequency and channel setting 16
- I power on 16
- Vfo and memory call channels 16
- D exchanging the displays 17
- Frequency and channel setting 17
- I main band selection 17
- I operating band selection 17
- D memory channels 18
- Frequency 18
- Frequency and channel setting 18
- I frequency or channel selection via the keypad 18
- D frequency 19
- D memory channels 19
- Frequency and channel setting 19
- I lock function 19
- I using the tuning dial 19
- Setting tuning dial increments 20
- Basic operation 21
- Caution transmitting without an antenna may damage the transceiver 21
- Convenient monitor function push and hold sql to listen to weak sig nals without disturbing the squelch settings quick guide function push the desired key while pushing l g for a quick description of the key s function p 34 21
- E set the squelch level 21
- I receive and transmit 21
- Q push power for 2 sec to turn power on w adjust the vol control to the desired level 21
- R set an operating frequency when a signal is received 21
- T push h l to toggle output power between high and low 21
- U release ptt to return to receive 21
- Y push and hold ptt to transmit then speak into the mic 21
- Basic operation 22
- D beep tones on off 22
- D crossband full duplex operation 22
- Initial set mode 22
- I general 23
- Repeater operation 23
- I offset frequency 24
- I subaudible tones 24
- Repeater operation 24
- Set mode 24
- I auto repeater function 25
- Initial set mode 25
- Repeater operation 25
- I general 26
- Memory call programming 26
- Programming during selection 26
- D memory call memory call 27
- D memory call vfo 27
- I memory edi 27
- I programming after selection 27
- Memory call programming 27
- Transferring 27
- D frequency name 28
- D programming memory names 28
- I memory names 28
- Memory call programming 28
- I memory clear 29
- Memory call programming 29
- Dtmf memory 30
- I programming a dtmf code 30
- D using a dtmf memory channel 31
- Dtmf memory 31
- I dtmf transmission speed 31
- I transmitting a dtmf code 31
- Initial set mode 31
- Each band has 3 scan types with skip functions and 4 resume conditions providing scanning versatility scans on both bands can be operated separately or simultaneously 32
- Frequency skip function p 31 skips unwanted frequen cies that inconveniently stop scanning this func tion can be turned on and off in scan set mode 32
- Full scan p 29 repeatedly scans all fre quencies over the entire band 32
- I scan types 32
- Memory skip scan p 29 repeatedly scans memory channels except skip channels 32
- Programmed scan p 29 32
- Scan operation 32
- Scan resume condition p 30 32
- I full programmed scan 33
- I memory scan 33
- Scan operation 33
- I scan resume condition 34
- I skip channel setting 34
- Scan operation 34
- Scan set mode 34
- D frequency skip function on off 35
- D programming a skip frequency 35
- I frequency skip function 35
- Scan operation 35
- Scan set mode 35
- I tone squelch operation 36
- Subaudible tone operation 36
- D calling a waiting station using pocket beep 37
- D waiting for a call from a specific station 37
- I pocket beep operation 37
- I tone scan 37
- Subaudible tone operation 37
- I battery voltage indication 38
- I guide function 38
- Initial set mode 38
- Other functions 38
- Function display backlighting 39
- I auto power off function 39
- Initial set mode 39
- I lcd contrast 40
- I power saver 40
- Initial set mode 40
- Other functions 40
- D setting the hm 75a functions 41
- I optional hm 75a functions 41
- Initial set mode 41
- Other functions 41
- I all reset 42
- I handheld to handheld cloning 42
- I partial reset 42
- Other functions 42
- Power on 42
- If your transceiver seems to be malfunctioning please check the following points before sending it to a service center 43
- Problem possible cause solution ref 43
- Troubleshootin 43
- Although the following chart refers mainly to the vhf right band the same arrangement applies to the uhf left band except commonly used mode dtmf memory scan set and initial set 44
- Call channel mode 44
- Memory mode 44
- Mode arrangement 44
- Vfo mode dtmf memory mode 44
- Initial set mode 45
- Mode arrangement 45
- Scan set mode 45
- Set mode 45
- All stated specifications are subject to change without notice or obligation 46
- Specifications 46
- D battery packs 47
- D carrying case 47
- D chargers and cables 47
- D others 47
- D speaker microphones 47
- Option 47
- 9 16 kamihigashi hirano ku osaka 547 japan 48
Похожие устройства
- Ardo 56 GG40 VX Инструкция по эксплуатации
- Samsung ST76 Red Инструкция по эксплуатации
- Icom ID-800H Инструкция по эксплуатации
- Ardo 56 GG40 X Инструкция по эксплуатации
- Samsung ST76 Silver Инструкция по эксплуатации
- Icom IC-A3 Инструкция по эксплуатации
- Ardo 56 GG40 W Инструкция по эксплуатации
- Sony DSC-W610 Pink Инструкция по эксплуатации
- Icom IC-A5 Инструкция по эксплуатации
- Ardo 55 GG40 VX Инструкция по эксплуатации
- Sony DSC-W610 Silver Инструкция по эксплуатации
- Icom IC-A23 Инструкция по эксплуатации
- Ardo 55 GG40 X Инструкция по эксплуатации
- Samsung DV300F Silver/Red Инструкция по эксплуатации
- Icom IC-A200 Инструкция по эксплуатации
- Ardo 55 GG40 W Инструкция по эксплуатации
- Nikon Coolpix S6300 Black Инструкция по эксплуатации
- Icom IC-F11 Инструкция по эксплуатации
- Ardo A 5540 G6 Инструкция по эксплуатации
- Sony DSC-H90 Red Инструкция по эксплуатации