Metabo Ku 6872 [7/48] Original instructions
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Metabo Ku 6872 [7/48] Original instructions

Metabo Ku 6872 [7/48] Original instructions
ENGLISH en
7
Original instructions
We, being solely responsible, hereby declare that
these curve shears conform to the standards and
directives specified on page 3.
The machine is designed for cutting through and
trimming sheet material and cuttable plastics.
The user bears sole responsibility for damage
caused by improper use.
Generally accepted accident prevention
regulations and the enclosed safety information
must be observed.
For your own protection and for the
protection of your electrical tool, pay
attention to all parts of the text that are
marked with this symbol!
WARNING – Reading the operating instruc-
tions will reduce the risk of injury.
WARNING Read all safety warnings and
instructions. Failure to follow all safety warn-
ings and instructions may result in electric shock,
fire and/or serious injury.
Keep all safety instructions and information for
future reference.
Pass on your electrical tool only together with these
documents.
Pull the plug out of the plug socket before any
adjustments or servicing are performed.
Avoid inadvertent starts: always switch the tool off
when the plug is removed from the mains socket or
if there has been a power cut.
Wear ear protectors. Exposure to noise can cause
loss of hearing.
Always wear protective goggles, gloves, and sturdy
shoes when working with this tool.
Secure the workpiece, e.g. using clamps.
Keep hands away from the cutting area.
Always switch on the machine before offering
up to the workpiece.
Always work with the metal guide plate
attached (3).
SYMBOLS ON THE TOOL:
..........Class II Construction
V ............. volts
A .............amperes
Hz ...........hertz
W ............watt
n
0
............ Stroke rate at idle speed
min.......... minutes
spm......... Stroke rate per minute
~............. alternating current
max. GA.. maximum material thickness
See page 3.
1Support bracket
2 Sliding switch
3Guide plate
4Screw for attaching the cutting base
5 Screw for attaching the blade
(to the ram)
6 Blade in the ram
7 Blade in the cutting base
8 Grub screw
9 Screw for attaching the blade
(to the cutting base)
10 Cutting base
Before plugging in, check to see that the rated
mains voltage and mains frequency,
as stated on the rating label, match your power
supply.
7.1 Adjusting the Distance Between the
Blades
The correct distance:
The distance between the blade (7) in the
cutting base and the blade (6) in the ram should be
approx a fifth of the thickness of the sheet material
being cut (i.e. when cutting a sheet 1.6 mm thick,
0.2 x 1.6 = 0.32 mm). The distance should be
slightly less if the material is tough and slightly more
if the material is brittle.
The blades should not move.
Adjusting the distance:
- Loosen the screw (9) and if necessary, the grub
screw (8) as well.
- Adjust the distance between the blade (7) in the
cutting base and the blade (6) in the ram using a
feeler gauge.
- Screw in the grub screw (8) until it rests against
the blade (7) in the cutting base and then tighten
the screw (9) again.
7.2 Switching On and Off
Switching on:
Push the sliding switch (2) forwards until it latches
into position. The symbol "I" then appears from
behind the sliding switch.
Switching off:
When the switch is set to on, press down the
1. Conformity Declaration
2. Specified Use
3. General Safety Instructions
4. Special Safety Instructions
5. Overview
6. Commissioning
7. Use

Содержание

Похожие устройства

Скачать