Home
Главная
Panasonic
Сплит-Системы
CS-F50DD1E5 / CU-B50DBE8
Сервис мануал Страница: 124

Panasonic CS-F50DD1E5 / CU-B50DBE8 [124/147] Cs f34dd1e5 cu b34dbe8

13.4.2.5. CS-F34DD1E5 CU-B34DBE8

Model Heating capacities are based on conditions

CS-F34DD1E5 CU-B34DBE8 3 phase, 50Hz, 400V

Heating capacity Indoor temp. 20°C D.B.

11.2 kW Outdoor temp. 7°C D.B. 6°C W.B.

Standard air volume 40 m

/min

TC : Cooling Capacity

SHC : Sensible Heat Capacity

IPT : Cooling Power Consumption

124

Содержание

Air conditioner 1
Contents 1
Cs f24dd1e5 cu b24dbe5 cs f28dd1e5 cu b28dbe5 cs f28dd1e5 cu b28dbe8 cs f34dd1e5 cu b34dbe5 1
Cs f34dd1e5 cu b34dbe8 cs f43dd1e5 cu b43dbe8 cs f50dd1e5 cu b50dbe8 1
Page page 1
A if main power supply is switched on with the wrong connection 3
B when changing the connection or combination of units due to re installation etc 3
Caution during automatic address setting 3
Caution of test operation 3
Do not touch the remote control switch and do not change any wirings for one minute when the main power supply switch is on because the unit is having automatic address setting during the first one minute 3
Example of trouble at test operation 3
If found out as following phenomenon at test operation on site it may have possibility of wrong address setting therefore please ensure of the address setting 3
Indoor and outdoor temperature 3
Lcd display had indicated as normal illumination when power supply switch is on however outdoor unit cannot be operated but it is necessary to take 3 to 5 minutes for outdoor unit to start from the timing of remote control on off switch is on 3
Lcd display of wired remote control had not illuminate although the main power supply switch is on 3
Manual address setting is also possible by using dip switch on indoor unit p c board however this address setting is only possible when made proper wiring connection and also indoor unit should be original virgin unit 3
Model 50hz b24dbe5 b28dbe5 b28dbe8 b34dbe5 b34dbe8 b43dbe8 b50dbe8 3
Operation range 3
P c board had memorized wrong setting information 3
Power supply 3
Service information 3
The applicable voltage range for each unit is given in the following table the working voltage among the three phases must be balanced within 3 deviation from each voltage at the compressor terminals the starting voltage must be higher than 85 of the rated voltage 3
The new duct type new outdoor models are possible to have address setting for twin control by automatic when main power supply is switched on 3
When changing the system from twin control to normal one to one system 3
When main power supply switch is on the p c board will automatically memorized the connecting system consequently when initial power supply is on there will not be interchangeability of units even of the same type and same capacity unit therefore unable to connect the unit to another system 3
When making the replacement of units as master and slave etc 3
Easy maintenance 4
Features 4
Flexible installation 4
Flexible installation in smaller spaces 4
Hide away type 4
Low ambient cooling operation 4
Outdoor unit 4
Quiet efficient design 4
Thin lightweight design 4
A brand new control method using the latest in technology 5
Group control equipment 5
Twin operation 5
Cooling capacities are based on indoor temperature of 27 c d b 80 f d b 19 c w b 66 f w b and outdoor air temperature of 35 c d b 95 f d b 24 c w b 75 f w b 6
Cs f24dd1e5 cu b24dbe5 6
D b 6 c w b 42 f w b 6
Electrical data 50 hz 6
Heating capacities are based on indoor temperature 20 c d b 68 f d b and outdoor air temperature of 7 c d b 44 f 6
Specification 6
Cooling capacities are based on indoor temperature of 27 c d b 80 f d b 19 c w b 66 f w b and outdoor air temperature of 35 c d b 95 f d b 24 c w b 75 f w b 7
Cs f28dd1e5 cu b28dbe5 7
Electrical data 50 hz 7
Heating capacities are based on indoor temperature of 20 c d b 68 f d b and outdoor air temperature of 7 c d b 44 f d b 6 c w b 42 f w b 7
Cooling capacities are based on indoor temperature of 27 c d b 80 f d b 19 c w b 66 f w b and outdoor air temperature of 35 c d b 95 f d b 24 c w b 75 f w b 8
Cs f28dd1e5 cu b28dbe8 8
Electrical data 50 hz 8
Heating capacities are based on indoor temperature of 20 c d b 68 f d b and outdoor air temperature of 7 c d b 44 f d b 6 c w b 42 f w b 8
Cooling capacities are based on indoor temperature of 27 c d b 80 f d b 19 c w b 66 f w b and outdoor air temperature of 35 c d b 95 f d b 24 c w b 75 f w b 9
Cs f34dd1e5 cu b34dbe5 9
D b 6 c w b 42 f w b 9
Electrical data 50 hz 9
Heating capacities are based on indoor temperature 20 c d b 68 f d b and outdoor air temperature of 7 c d b 44 f 9
Cooling capacities are based on indoor temperature of 27 c d b 80 f d b 19 c w b 66 f w b and outdoor air temperature of 35 c d b 95 f d b 24 c w b 75 f w b 10
Cs f34dd1e5 cu b34dbe8 10
D b 6 c w b 42 f w b 10
Electrical data 50 hz 10
Heating capacities are based on indoor temperature 20 c d b 68 f d b and outdoor air temperature of 7 c d b 44 f 10
Cooling capacities are based on indoor temperature of 27 c d b 80 f d b 19 c w b 66 f w b and outdoor air temperature of 35 c d b 95 f d b 24 c w b 75 f w b 11
Cs f43dd1e5 cu b43dbe8 11
Electrical data 50 hz 11
Heating capacities are based on indoor temperature of 20 c d b 68 f d b and outdoor air temperature of 7 c d b 44 f d b 6 c w b 42 f w b 11
Cooling capacities are based on indoor temperature of 27 c d b 80 f d b 19 c w b 66 f w b and outdoor air temperature of 35 c d b 95 f d b 24 c w b 75 f w b 12
Cs f50dd1e5 cu b50dbe8 12
Electrical data 50 hz 12
Heating capacities are based on indoor temperature of 20 c d b 68 f d b and outdoor air temperature of 7 c d b 44 f d b 6 c w b 42 f w b 12
Dimensions 13
Refrigeration cycle 18
Block diagram 20
Wiring diagram 22
Are not available for operation if one of these buttons is pressed function will not be available 28
Buttons marked with 28
Buttons marked with are not needed for normal operation if one of these buttons is pressed by mistake press the same button once more to cancel the operation 28
Do not operate the remote control with wet hands otherwise electric shock or malfunction may occur 28
Do not press the remote control buttons with sharp object as this may damage the remote control 28
Ensure that the correct button is pressed as simultaneous pressing of the multiple buttons will not make the setting correct 28
Name and function of each part 28
The illustration above is for explanatory purposes only the appearance will be different during actual operation 28
When the power resumed after power failure the unit will restart automatically with all the previous settings preserved by the memory function auto restart function 28
Wired remote control operating instructions 28
How to select the timer 31
How to set remote control day and time 31
Daily timer setting 32
Cannot set 2 programs with same time setting in a day 33
Display 33
Final display of daily timer 33
How to set weekly timer 33
On timer can be set together with your desired temperature however this temperature will be used continuously 33
Single one day setting 33
Weekly timer setting 33
You also may select collective many days with same time setting or individual 33
You can set the timer for 1 week monday to sunday with 6 programs per day 33
A monday to friday same time 1st program on 9 00 2nd program off 16 00 34
B only wednesday additional 3rd program off 12 30 4th program on 13 30 34
C only saturday 1st program on 10 00 with 20 c 2nd program off 14 00 34
D sunday holiday no need to set any timer 34
For example if you want to set 34
Timer that has setting nearest to current time and day will be activated first 34
To check the setting timer press select button then up or down button to select day the display will show each program for the selected day 34
To reset the setting for all press select button then ensure all day setting with triangle mark then press cancel button for all the programs 34
Cooling operation 35
Operation detail 35
Auto operation 36
Fan operation 36
Heating operation 36
Soft dry operation 36
Auto fan speed 37
Cooling indoor fan control 37
Heating indoor fan control 37
However when operation start or during operation fan speed control is limited due to prevent a cold draft for example when heating operation start 37
If thermostat is off indoor fan fixed low speed 37
Manual fan speed 37
Normal control 37
Operation starts at high medium or low speed set by remote control 37
When operation start or during operation fan speed control by detecting indoor heat exchanger as follows 37
When operation starts or shifting to thermostat on condition from thermostat off condition indoor fan operates as below 37
After 2 minutes the outdoor pipe temperature is detected and the outdoor unit fan speed is changed automatically 38
Cooling outdoor fan control 38
Depending on differences between room temperature and setting temperature compressor operation is decided and starts operation 38
During cooling operation outdoor fan speed changes according to outdoor pipe temperature 38
During heating operation the fan speed is controlled by indoor heat exchanger temperature 38
Heating outdoor fan control 38
If temperature difference matches values shown below thermostat switches off 38
In case of twin operation the higher indoor heat exchanger temperature is used to control the fan speed during heating operation the fan speed is controlled by indoor heat exchanger temperature 38
Odour cut control 38
Odour cut operation removes the odour generated at indoor heat exchanger by using drain water come out from indoor heat exchanger 38
Odour cut operation starts when compressor or thermostat is on 38
Operation control 38
Outdoor fan on time is a variable with the range of 200ms to 2000ms 38
Press odour button at remote control to enable odour cut operation 38
The fan speed is controlled by the timing of turning the outdoor fan on and off within an interval 38
Thermostat control 38
When outdoor pipe temperature increases internal timing also increases 38
Energy save control 39
Hot start control 39
Powerful control 39
Deice control 40
Dew form prevention control 40
Freeze prevention control 40
Crank case heater control 41
Outdoor fan remaining heat removal control 41
Outdoor low pressure protection control 41
Protection control 41
Pump down 41
Time delay safe control 41
Connection capacity protection control 42
Ct disconnection detection control 42
Discharge temperature protection control 42
Outdoor high pressure protection control 42
Over current protection control 42
Sensor disconnection detection control 42
Four way valve error detection control 43
High pressure switch disconnection error detection control 43
Low pressure switch disconnection error detection control 43
Test run 43
Valve error detection control 43
Add refrigerant main pipe branch pipe la branch pipe lb 2 8 30 50 formula 2 44
Add refrigerant main pipe branch pipe la branch pipe lb 30 50 formula 4 44
Calculation 1 44
Calculation 2 44
Correction of capacities 44
Correction of capacities according to the connecting pipe length the data of rated capacities marked on the name plate are based on 7 metres connecting pipe and horizontal installation 44
In case of cu b28dbe5 b28dbe8 b34dbe5 b34dbe8 44
In case of cu b43dbe8 b50dbe8 44
Installation instruction 44
Pipe length 44
Pipe length main pipe branch pipe la branch pipe lb 2 8 formula 1 44
Pipe length main pipe branch pipe la branch pipe lb formula 3 44
Piping elevation b outdoor unit installed at top 44
Piping elevation c outdoor unit installed at bottom 44
When pipe length exceed 30m calculated by formula 1 adding refrigerant amount should be calculated by formula 2 if calculation result is less than 30m it is not necessary to add refrigerant 44
When pipe length exceed 30m calculated by formula 3 adding refrigerant amount should be calculated by formula 4 if calculation result is less than 30m it is not necessary to add refrigerant 44
Before shipment this air conditioner is filled with the rated amount of refrigerant subject to 30m piping length the rated amount of refrigerant is indicated on the name plate but when the piping length exceeds 30m additional charge is required according to the following table 46
Example cs f24dd1e5 in case of 31m long pipe one way the amount of refrigerant to be replenished is 31 30 x 50 50g 46
Position of the centre gravity 46
Refrigerant additional charge 46
The piping length exceeds 30 metres applicable for all models 46
After installation work has been completed do not only make sure that the unit is free from any abnormal condition through the execution of trial run but also explain how to use and how to perform maintenance of this unit to the customer according to the instruction manual 47
As to indications with illustration 47
Cautions such items also have a chance for leading to significant result depending on the situations 47
Cautions those that have much chances for leading to significant result such as fatality or serious injury if wrong installation would have been carried out are listed compiling them especially into the column of 47
However even in the case of items which are listed in the column of 47
In addition request the customer to keep this manual for installation work together with the instruction manual 47
In either case important descriptions regarding the safety are listed then observe them without fail 47
Indoor unit installation 47
Precautions shown here are differentiated between 47
Warnings 47
Warnings and 47
Accessories packed in the indoor unit container 48
If the height from the floor to ceiling exceeds three meters air flow distribution deteriorates and the effect is decreased 48
Install the indoor unit once the following conditions are satisfied and after receiving the customer approval 48
Place the indoor unit easy water drainage suitable dimension h is necessary to get slop to drain as figure 48
Provide a check port on the piping side ceiling for repair and maintenance 48
Selecting the location for the indoor unit 48
The indoor unit must allow easy connection to the outdoor unit 48
The indoor unit must allow easy draining 48
The indoor unit must be away from heat and steam sources but avoid installing it near an entrance 48
The indoor unit must be free from any obstacles in path of the air inlet and outlet and must allow spreading of air throughout the room 48
The indoor unit must be from at least 3m away from any noise generating equipment the electrical wiring must be shielded with a steel conduit 48
The indoor unit must be within a maintenance space 48
The installation position must be able to support a load four times the indoor unit weight 48
Warnings 48
Installation of indoor unit 50
Indoor unit drain piping 51
Refrigerant piping 51
Heat insulation 52
Always ground the air conditioner with a grounding wire and screw to meet the local regulations 53
Be sure to connect the wires correctly to terminal board with connecting the crimp type ring terminal to the wires 53
Be sure to turn off the main power before installing and connecting the remote controller 53
Electrical wiring 53
Feed the power source to the unit via a distribution switch board designed for this purpose the switch should disconnected all poles with a contact separation of at least 3 mm 53
Select a power source that is capable of supplying the current required by the air conditioner 53
Use the standard power cord for europe such as h05rn f or h07rn f which conforms to cenelec har rating specifications or use the cables based on iec standard 245iec57 245iec66 53
Settings 54
0 precautions in test run 55
As for timer output 55
Connect the timer cord to connector cn timer on print circuit board 55
If using the remote control unit to carry out test operation follow the procedure given below 55
Test operation can be carried out using the remote control unit or at the outdoor unit if carrying out test operation at the outdoor unit refer to test operation in the outdoor unit installation manual 55
The initial power supply must provide at least 90 of the rated voltage otherwise the air conditioner may not operate 55
1 check the following items when installation is complete 56
2 hand over 56
After installation work has been completed do not only make sure that the unit is free from any abnormal condition through the execution of try run but also explain how to use and how to perform maintenance of this unit to the customer according to the instruction manual 57
As to indications with illustration 57
Cautions such items also have a chance for leading to significant result depending on the situations 57
Cautions those that have much chances for leading to significant result such as fatality or serious injury if wrong installation would have been carried out are listed compiling them especially into the column of 57
However even in the case of items which are listed in the column of 57
In addition request the customer to keep this manual for installation work together with instruction manual 57
In either case important descriptions regarding the safety are listed then observe them without fail 57
Outdoor unit installation 57
Precautions shown here are differentiated between 57
Warnings 57
Warnings and 57
A brazing work 58
Accessories supplied with outdoor unit 58
Before installation work 58
Brazing work needs replacing air inside pipe with nitrogen gas in order to prevent oxidation scale from occurring this is called nitrogen replacement and one of very important work in brazing refrigerant piping oxidation preventive is not possible to use 58
Charge hose 58
Check that all accessory parts are present before installing the outdoor unit 58
Gas leakage detection warning device 58
Gauge manifold 58
Installation work 58
The following parts are supplied as accessories with each outdoor unit 58
There are tools and materials for both new refrigeration and usual refrigeration you can use together and for either two of them you can use use the below for new refrigeration 58
This product is using new refrigeration r410a the basic way of installation work is the same as usual but water and impurities should be controlled more strictly than before due to characteristic of refrigerating machine oil therefore selection of materials to use and processing storing and brazing need appropriate construction and control 58
Tools and materials 58
Vacuum pump with backflow preventor system 58
After that keep the pressure 100 kpa for 1 hour and confirm the vacuum gauge value not increasing 60
Dry vacuuming 60
For the use of a gas cylinder without siphon inside turn it upside down and use it 60
Handling the unit by hold the handle at compressor side and hold the basepan bottom at fan side 60
If vacuum gauge value is increase there is possibility of water inside the unit or there is any leakage 60
If vacuum pump possible vacuuming until less than 100 kpa 60
Regarding handling 60
Running vacuum pump at both liquid and gas side for more than 1 hour and vacuuming until 100 kpa 60
Select location which satisfies the following condition and then confirm with the customer that such a place is satisfactory before installing the outdoor unit 60
Selecting the outdoor unit installation locations 60
We recommend manifold with sight glass 60
Transporting and installing the outdoor unit 61
Connecting the pipes 62
Charging with refrigerant 63
Heat insulation 63
Clamp the wires securely to the terminal connections using cord clamps so that no undue force is placed on the wires 64
Connect the power supply wiring and indoor outdoor unit connection wiring according to the electrical circuit diagram instructions 64
Electrical wiring 64
Once all wiring work has been completed tie the wires and cords together with the binding strap so that they do not touch other parts such as the compressor and pipes 64
Operate the pump down according to the following procedures 64
Pump down operation 64
Earth lead wire shall be longer than other lead wires as shown in the figure for the electrical safety in case of the slipping out of the cord from the anchorage 65
Power supply specifications 65
0 connecting power supply cables 66
1 precautions with regard to test operation 66
Caution 66
For three phase model never operate the unit by pressing the electromagnetic switch 66
Never correct the phase by switching over any of the wires inside the unit 66
2 as to making the inspection after completion of work fully understood 67
3 as to delivery to the customer 67
As to the structure and appearance check following items 67
At the time when the work has been completed measure and record the characteristics of test run without fail and keep the measuring date etc 67
Carry out the measurement regarding room temperature outside air temperature suction and air discharge temperatures wind velocity wind volume voltage current presence of abnormal vibration operating pressure piping temperature compressive pressure airtight pressure as items to be measured 67
Deliver the instruction manual to the customer without fail 67
Request the customer to operate this air conditioner viewing instruction manual come with indoor unit in practice and explain how to operate 67
Accessories supplied with wired remote controller 68
Notes regarding wired remote controller setting up location 68
Wired remote controller installation 68
Remote controller installation 69
Settings 71
Self diagnosis function 73
Test operation 73
General 75
Piping connections 75
Refrigerant charging 75
Twin systems installation 75
Wiring 75
A chemical characteristics the chemical characteristics of r410a are similar to those of r22 in that both are chemically stable non flammable refrigerants with low toxicity however just like r22 the specific gravity of r410a gas is heavier than that of air because of this it can cause an oxygen deficiency if it leaks into a closed room since it collects in the lower area of the room it also generates toxic gas when it is directly exposed to a flame so it must be used in a well ventilated environment where it will not collect 76
About r410a refrigerant 76
B compositional change pseudo azeotropic characteristics r410a is a pseudo azeotropic mixture comprising the two components r32 and r125 multi component refrigerants with these chemical characteristics exhibit little compositional change even from phase changes due to vaporization or condensation which means that there is little change in the circulating refrigerant composition even when the refrigerant leaks from the gaseous section of the piping accordingly r410a can be handled in almost the same manner as the single component refrigerant r22 however when charging because there is a slight change in composition between the gas phase and the liquid phase inside a cylinder or other container charging should basically begin with the liquid side 76
C pressure characteristics as seen in table 2 the gas pressure of r410a is approximately 1 times as high as that of r22 at the same refrigerant temperature which means that special r410a tools and materials with high pressure specifications must be used for all refrigerant piping work and servicing 76
Converting air conditioners to r410a since it was declared in1974 that chlorofluorocarbons cfc hydro chlorofluorocarbons hcfc and other substances pose a destructive danger to the ozone layer in the earth s upper stratosphere 20 to 40 km above the earth measures have been taken around the world to prevent this destruction the r22 refrigerant which has conventionally been used in acs is an hcfc refrigerant and therefore possesses this ozone destroying potential international regulations the montreal protocol on ozone damaging substances and the domestic laws of various countries call for the early substitution of r22 by a refrigerant which will not harm the ozone layer 76
In acs the hfc refrigerant which has become the mainstream alternative is called r410a compared with r22 the pressure of r410a is approximately 1 times as high at the same refrigerant temperature but the energy efficiency is about the same consisting of hydrogen h fluorine f and carbon c r410a is an hfc refrigerant another typical hfc refrigerant is r407c while the energy efficiency of r407c is somewhat inferior to that of r410a it offers the advantage of having pressure characteristics which are about the same as those of r22 and is used mainly in packaged acs 76
Installation servicing air conditioner 76
Outline 76
The characteristics of hfc r410a refrigerants 76
1 always replace the dryer of the outdoor unit at the same time the replacement dryer is wrapped in a vacuum pack replace it last among the refrigerating cycle parts start brazing as soon as you have opened the vacuum pack and begin the vacuuming operation within 2 hours 77
1 you can use the conventional r22 flaring tool if you need to buy a new tool buy the r410a type 77
2 use when it is necessary to detect small gas leaks 77
After finishing the installation check to make sure there is no refrigerant gas leaking 77
Cause the gas pressure of r410a is approximately 1 times as high as that of r22 a mistake in installation or servicing could result in a major accident it is essential that you use r410a tools and materials and that you observe the following precautions to ensure safety 77
D r410a refrigerating machine oil conventionally mineral oil or a synthetic oil such as alkylbenzene has been used for r22 refrigerating machine oil because of the poor compatibility between r410a and conventional oils like mineral oil however there is a tendency for the refrigerating machine oil to collect in the refrigerating cycle for this reason polyester and other synthetic oils which have a high compatibility with r410a are used as refrigerating machine oil because of the high hygroscopic property of synthetic oil more care must be taken in its handling than was necessary with conventional refrigerating machine oils also these synthetic oils will degrade if mixed with mineral oil or alkylbenzene causing clogging in capillary tubes or compressor malfunction do not mix them under any circumstances 77
Do not perform any alterations on the ac unit under any circumstances have all repair work done by a specialist incorrect repairs can result in a water leakage electric shock fire etc 77
Do not use any refrigerant other than r410a in acs that have been used with r410a 77
For other installation work you should have the usual tools such as screwdrivers a metal cutting saw an electrical drill a hole core drill 65 or 70 dia a tape measure a level a thermometer a clamp meter an insulation tester a voltmeter etc 77
If any refrigerant gas leaks while you are working ventilate the room toxic gas may be generated if refrigerant gas is exposed to a direct flame 77
In order to prevent an r410a ac from mistakenly being charged with any other refrigerant the diameter of the 3 way valve service port on the outdoor unit has been changed also to increase its ability to withstand pressure the opposing dimensions have been changed for the refrigerant pipe flaring size and flare nut accordingly when installing or servicing refrigerant piping you must have both the r410a and ordinary tools listed below 77
Necessary tools 77
Safety measures when installing servicing refrigerant piping 77
Tools for installing servicing refrigerant piping 77
When installing or transferring an ac do not allow any air or substance other than r410a to mix into the refrigeration cycle if it does the pressure in the refrigeration cycle can become abnormally high possibly causing an explosion and or injury 77
When installing or transferring an ac follow the instructions in the installation instructions carefully incorrect installation can result in an abnormal refrigeration cycle or water leakage electric shock fire etc 77
Because the pressure is higher for the r410a type the conventional type cannot be used 78
Copper tube gauge for clearance adjustment used when flaring with the conventional flaring tool clutch type 78
Flaring tool clutch type 78
In the r410a flaring tool the receiving hole for the clamp bar is enlarged so the clearance from the clamp bar can be set to 0 0 mm and the spring inside the tool is strengthened to increase the strength of the pipe expanding torque this flaring tools can also be used with r22 piping so we recommend that you select it if you are buying a new flaring tool 78
Manifold gauge 78
R410a tools 78
The shape of the manifold ports has been changed to prevent the possibility of mistakenly charging with another type of refrigerant 78
This gauge makes it easy to set the clearance for the copper tube to 1 1 mm from the clamp bar of the flaring tool 78
Torque wrenches 78
R410a tools which are usable for r22 models 80
Piping materials 81
Processing and connecting piping materials 81
Refrigerant piping work 81
A check to make sure there is no scratches dust etc on the flare and union 82
A sheathed copper pipes and copper element pipes when using these pipes check to make sure that they are the stipulated thickness for flare nuts be sure to used the same nut that is used on the ac unit 82
B align the flared surface with the axial center of the union 82
Because the gas pressure of r410a is approximately 1 times as high as that of r22 copper pipes with the thickness shown in table 10 and with minimal impurities must be used care must also be taken during storage to ensure that pipes are not crushed deformed or scratched and that no dust moisture or other substance enters the pipe interior when storing sheathed copper pipes or plain copper pipes seal the openings by pinching or taping them securely 82
C use a torque wrench and tighten to the specified torque the tightening torque for r410a is the same as the conventional torque value for r22 be careful because if the torque is too weak it may lead to a gas leak if it is too strong it may split the flare nut or make it impossible to remove the flare nut 82
Makings and management 82
Procedure and precautions for flare connection 82
Storing and managing piping materials 82
Types of piping and their storage the following is a general classification of the refrigerant pipe materials used for acs 82
Inspecting gas leaks with a vacuum pump for new installations using new refrigerant piping 83
Installation transferring servicing 83
Ac units replacement using existing refrigerant piping 84
Recharging refrigerant during servicing 84
Refrigerant compatibility using r410a refrigerant in r22 acs and vice versa 84
Transferring using new refrigerant piping 84
Brazing 86
Servicing tips 86
For standard installation 87
Trouble shooting guide 87
During twin operation 89
During group control operation 91
Test operation and self diagnosis 92
Test operation from the outdoor unit 92
Test run forced cooling mode and heating mode 92
Self diagnosis function 93
Test operation using the wired remote control 93
Check the resistance of each thermistor of both indoor and outdoor units by referring the resistance table as follows 95
During outdoor unit emergency operation or test operation the led on the p c b will flash 95
Emergency operation 95
If abnormality detected in the indoor or outdoor unit turn off the main power supply and find the cause 95
If there is an abnormality in the temperature thermistor disconnect or shorted indoor unit cannot be operated 95
Thermistor resistance table 95
If the problem disappears and operation returns to normal the check display on the remote control unit will switch off but the self diagnosis led will remain illuminated until operation is resumed 96
Refer to the table below to remove the cause of the problem and then re start the air conditioner system 96
Self diagnosis error code table 96
The display screen on the wired remote control unit and the self diagnosis leds green on the outdoor unit printed circuit board in the outdoor unit can be used to indicate where the location of a problem is 96
Technical data 98
Sound measurement point 104
Discharge and suction pressure 105
Saturation temperature of discharge and suction pressure 105
Capacity and power consumption 107
Cooling performance 107
Cs f24dd1e5 cu b24dbe5 107
Ipt cooling power consumption 107
Shc sensible heat capacity 107
Tc cooling capacity 107
Cs f28dd1e5 cu b28dbe5 109
Ipt cooling power consumption 109
Shc sensible heat capacity 109
Tc cooling capacity 109
Cs f28dd1e5 cu b28dbe8 111
Ipt cooling power consumption 111
Shc sensible heat capacity 111
Tc cooling capacity 111
Cs f34dd1e5 cu b34dbe5 113
Ipt cooling power consumption 113
Shc sensible heat capacity 113
Tc cooling capacity 113
Cs f34dd1e5 cu b34dbe8 115
Ipt cooling power consumption 115
Shc sensible heat capacity 115
Tc cooling capacity 115
Cs f43dd1e5 cu b43dbe8 117
Ipt cooling power consumption 117
Shc sensible heat capacity 117
Tc cooling capacity 117
Cs f50dd1e5 cu b50dbe8 119
Ipt cooling power consumption 119
Shc sensible heat capacity 119
Tc cooling capacity 119
Cs f24dd1e5 cu b24dbe5 121
Cs f28dd1e5 cu b28dbe5 121
Cs f28dd1e5 cu b28dbe8 121
Heating performance 121
Cs f34dd1e5 cu b34dbe5 122
Ipt cooling power consumption 122
Shc sensible heat capacity 122
Tc cooling capacity 122
Cs f34dd1e5 cu b34dbe8 124
Ipt cooling power consumption 124
Shc sensible heat capacity 124
Tc cooling capacity 124
Cs f43dd1e5 cu b43dbe8 126
Ipt cooling power consumption 126
Shc sensible heat capacity 126
Tc cooling capacity 126
Cs f50dd1e5 cu b50dbe8 128
Ipt cooling power consumption 128
Shc sensible heat capacity 128
Tc cooling capacity 128
Cs f24dd1e5 130
Fan performance 130
Cs f28dd1e5 131
Cs f34dd1e5 132
Cs f43dd1e5 133
Cs f50dd1e5 134
Indoor unit 135
Mpa 10 kgf c 135
Outdoor unit 135
Safety device 135
Operating characteristics 136
Indoor unit 137
Replacement parts 137
All parts are supplied from taiwan ptw 138
Casing included with impeller part 138
Cs f24dd1e5 cs f28dd1e5 cs f34dd1e5 cs f43dd1e5 cs f50dd1e5 138
Outdoor unit 139
All parts are supplied from phaam malaysia vendor code 061 141
All parts are supplied from phaam malaysia vendor code 061 145
Indoor unit 146
Print pattern 146
Outdoor unit 147

Panasonic CS-F50DD1E5 / CU-B50DBE8 [124/147] Cs f34dd1e5 cu b34dbe8

Содержание

Похожие устройства