![Makita TD0100 [6/20] Accessories](/img/pdf.png)
Makita TD0100 [6/20] Accessories
![Makita TD0100 [6/20] Accessories](/views2/1632049/page6/bg6.png)
6
• When fastening screw M8 or smaller, carefully
adjust pressure on the switch trigger so that the
screw is not damaged.
• Hold the tool pointed straight at the screw.
• If you tighten the screw for a time longer than
shown in the figures, the screw or the point of the
driver bit may be overstressed, stripped, damaged,
etc. Before starting your job, always perform a test
operation to determine the proper fastening time
for your screw.
The fastening torque is affected by a wide variety of
factors including the following. After fastening, always
check the torque with a torque wrench.
1. Driver bit or socket bit
Failure to use the correct size driver bit or socket
bit will cause a reduction in the fastening torque.
2. Bolt
• Even though the torque coefficient and the
class of bolt are the same, the proper
fastening torque will differ according to the
diameter of bolt.
• Even though the diameters of bolts are the
same, the proper fastening torque will differ
according to the torque coefficient, the class of
bolt and the bolt length.
3. The manner of holding the tool or the material of
driving position to be fastened will affect the
torque.
4. Operating the tool at low speed will cause a
reduction in the fastening torque.
MAINTENANCE
CAUTION:
• Always be sure that the tool is switched off and
unplugged before attempting to perform inspection
or maintenance.
To maintain product SAFETY and RELIABILITY, repairs,
carbon brush inspection and replacement, any other
maintenance or adjustment should be performed by
Makita Authorized or Factory Service Centers, always
using Makita replacement parts.
ACCESSORIES
CAUTION:
• These accessories or attachments are
recommended for use with your Makita tool
specified in this manual. The use of any other
accessories or attachments might present a risk of
injury to persons. Only use accessory or
attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita Service Center.
• Screw bits
• Socket bits
• Adjustable locator with bit
Adjustable locator with bit
1
2
009624
To use the adjustable locator with bit, remove the
bumper and then install it. The bumper can be removed
by pulling forward.
1. Bumper
2. Hammer case
cover
Содержание
- Impact driver visseuse à chocs atornillador de impacto 1
- Instruction manual manuel d instruction manual de instrucciones 1
- Td0100 1
- General safety rules 2
- Save these instructions 2
- Specifications 2
- 6 18 16 16 14 18 16 14 12 6 10 10 12 16 16 14 12 12 16 14 12 not recommended 3
- Ampere rating volts total length of cord in feet 3
- More than not more than awg 3
- Save these instructions 3
- Specific safety rules 3
- Table 1 minimum gage for cord 3
- V 25 ft 50 ft 100 ft 150 ft 3
- Assembly 4
- Functional description 4
- Holding the tool 4
- Installing or removing driver bit or socket bit 4
- Reversing switch action 4
- Switch action 4
- Symbols 4
- Warning 4
- 72 m14 9 16 5
- Bit 2 sleeve 5
- Fastening time 5
- Fastening torque 5
- High tensile bolt n m ft lbs 5
- Hold the tool firmly and place the point of the driver bit in the screw head apply forward pressure to the tool to the extent that the bit will not slip off the screw and turn the tool on to start operation 5
- If the bit is not inserted deep enough into the sleeve the sleeve will not return to its original position and the bit will not be secured in this case try re inserting the bit according to the instructions above 5
- Operation 5
- Proper fastening torque 5
- Standard bolt n m ft lbs 5
- The proper fastening torque may differ depending upon the kind or size of the screw bolt the material of the workpiece to be fastened etc the relation between fastening torque and fastening time is shown in the figures 5
- The size of wood screw which can be fastened with this tool may differ depending upon the type of material to be fastened always perform a test operation to determine the size of wood screw holding the tool hold the tool only by the handle when performing an operation 5
- To remove the bit pull the sleeve in the direction of the arrow and pull the bit out firmly 5
- Use the proper bit for the head of the screw bolt that you wish to use 5
- Accessories 6
- Adjustable locator with bit 6
- Maintenance 6
- Makita limited one year warranty 7
- Repairs have been made or attempted by others repairs are required because of normal wear and tear the tool has been abused misused or improperly maintained alterations have been made to the tool 7
- Conservez ce mode d emploi 8
- Règles de sécurité générales 8
- Spécifications 8
- 6 18 16 16 14 18 16 14 12 6 10 10 12 16 16 14 12 12 16 14 12 non recomman 10
- Avertissement 10
- Conservez ce mode d emploi 10
- Description du fonctionnement 10
- Intensi 10
- Interrupteur 10
- Nominale volts longueur totale du cordon en pieds 120 v 25 pi 50 pi 100 pi 150 pi 10
- Plus de pas plus de calibre a 10
- Ricain des fils 10
- Règles de sécurité particulières 10
- Symboles 10
- Tableau 1 gabarit minimum du cordon 10
- Assemblage 11
- Installation ou retrait de l embout ou l embout à douille 11
- Inverseur 11
- Prise de l outil 11
- Utilisation 11
- Accessoires 13
- Centreur réglable avec embout 13
- Entretien 13
- Garantie limitée d un an makita 13
- Especificaciones 14
- Guarde estas instrucciones 14
- Normas generales de seguridad 14
- A 6 a 18 16 16 14 18 16 14 12 6 a 10 a 10 a 12 a 16 16 14 12 12 a 16 a 14 12 no se recomienda 16
- Advertencia 16
- Amperaje nominal 16
- Descripción del funcionamiento 16
- Guarde estas instrucciones 16
- Nimo para el cable 16
- Normas específicas de seguridad advertencias y precauciones 16
- S de calibre del cable awg 16
- S de no 16
- Símbolos 16
- Tabla 1 calibre 16
- Volts longitud total del cable en metros 120 v 16
- Accionamiento del conmutador de inversión de giro 17
- Accionamiento del interruptor 17
- Ensamble 17
- Instalar o quitar las puntas para atornillar 17
- Sujeción de la herramienta 17
- Operación 18
- Accesorios 19
- Garantía limitada makita de un año 19
- Localizador ajustable con la broca 19
- Mantenimiento 19
- Advertencia 20
- Makita corporation 20
- Warning 20
Похожие устройства
- Makita DDF485Z без акк и з.у Инструкция по эксплуатации
- Aurora COUNTRY 1100 MULTI-SHIFT (7 л.с., ширина 110 см, 4,8 л) Инструкция по эксплуатации
- Euroboor ECO.100S+/T Инструкция по эксплуатации
- Euroboor ECO.80S+ Инструкция по эксплуатации
- Orbis CLIMA MLW (OB320622) белый Инструкция по эксплуатации
- Orbis CLIMA FANCOIL (OB321232) белый Инструкция по эксплуатации
- Orbis NEO ML + (OB324400) белый Инструкция по эксплуатации
- ABION ASH-C098BE Инструкция по эксплуатации
- ABION ASH-C308BE Инструкция по эксплуатации
- ABION ASH-C128DC Инструкция по эксплуатации
- Military Перфоратор RH500 +Мини-дрель ME3,6 Инструкция по эксплуатации
- Makita УШМ (болгарка) DGA506RME +Сумка PGH-170100 Инструкция по эксплуатации
- Makita Бесщеточный шуруповерт DF032DWME 187264 +Рулетка PGC-80520 Инструкция по эксплуатации
- Hammer Перфоратор PRT650A +Отвертка аккумуляторная ACD3.6LE Инструкция по эксплуатации
- Makita DGA701ZU без акк. и з.у Инструкция по эксплуатации
- Makita DGA901ZU без акк. и з.у Инструкция по эксплуатации
- Makita PT354DZ без акк. и з.у Инструкция по эксплуатации
- Huter Снегоуборщик SGC 4000E + Болгарка DeWalt DWE4051 Инструкция по эксплуатации
- Dewalt УШМ (болгарка) DWE4227QS +Круг отрезной 125х1.2х22 DT42340ZQZ 5шт. Инструкция по эксплуатации
- Festool BHC 18 Li-Basic (574723) без акк. и з.у Инструкция по эксплуатации