Dewalt DCW200N-XJ без акк. и з.у — guidelines for Environmental Protection and Tool Maintenance [15/44]
Макгруп McGrp.ru

Dewalt DCW200N-XJ без акк. и з.у — guidelines for Environmental Protection and Tool Maintenance [15/44]

Превью страниц Страница 15 / 44
Dewalt DCW200N-XJ без акк. и з.у [15/44] Rechargeable battery pack
13
ENGLISH
Protecting the Environment
Separate collection. Products and batteries marked
with this symbol must not be disposed of with normal
householdwaste.
Products and batteries contain materials that can
be recovered or recycled reducing the demand for raw
materials. Please recycle electrical products and batteries
according to local provisions. Further information is available at
www.2helpU.com.
Rechargeable Battery Pack
This long life battery pack must be recharged when it fails
to produce sufficient power on jobs which were easily done
before. At the end of its technical life, discard it with due care for
our environment:
• Run the battery pack down completely, then remove it from
thetool.
• Li‑Ion cells are recyclable. Take them to your dealer or a
local recycling station. The collected battery packs will be
recycled or disposed ofproperly.
Included with the unit is a dust port which fits batteries 5Ah
andunder.
Available for purchase as a service part (N684701) is a dust port
for batteries 6Ah andover.
Optional Accessories
WARNING: Since accessories, other than those offered
by
DeWALT
, have not been tested with this product, use
of such accessories with this tool could be hazardous.
To reduce the risk of injury, only
DeWALT
recommended
accessories should be used with thisproduct.
Consult your dealer for further information on the
appropriateaccessories.
Cleaning
WARNING: Blow dirt and dust out of the main housing
with dry air as often as dirt is seen collecting in and around
the air vents. Wear approved eye protection and approved
dust mask when performing thisprocedure.
WARNING: Never use solvents or other harsh chemicals
for cleaning the non‑metallic parts of the tool. These
chemicals may weaken the materials used in these parts.
Use a cloth dampened only with water and mild soap.
Never let any liquid get inside the tool; never immerse any
part of the tool into aliquid.
Lubrication
Your power tool requires no additionallubrication.
Tool Care
• Keep your machine as clean as possible by wiping with
a clean cloth and blowing through it with air after every
5hours ofuse.
• Don’t use harsh chemicals or solvents to clean the tool.
These chemicals could seriously damage theplastic.
• Avoid overloading your sander. Overloading will result in
a considerable reduction in speed and efficiency and the
unit will become hot. In this event, run sander at a “no load”
condition for a minute ortwo.
MAINTENANCE
Your power tool has been designed to operate over a long
period of time with a minimum of maintenance. Continuous
satisfactory operation depends upon proper tool care and
regularcleaning.
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start‑up can causeinjury.
The charger and battery pack are notserviceable.
Replacing the Sanding Pad (Fig.K)
The sanding pad
3
is designed to be a consumable part and
will occasionally need to be replaced. The sanding pad needs
replacement when signs of wear become evident. Sanding pads
are available at extra cost from your local dealer or authorized
DeWALT
servicecenter.
1. Holding the base firmly, remove the four screws
14
from
the bottom of thepad.
2. Remove the pad
3
.
3. Reinstall pad. Replace the four screws. Be careful not to
over‑tightenscrews.

Содержание

210

Похожие устройства

Learn how to protect the environment through proper disposal and recycling of batteries and electrical products. Discover essential maintenance tips for your power tools.

Google Play RuStore