![Zotek ZT-303 [6/27] To the line being measured do not touch the](/img/pdf.png)
Zotek ZT-303 [6/27] To the line being measured do not touch the
![Zotek ZT-303 [6/27] To the line being measured do not touch the](/views2/1893228/page6/bg6.png)
• Keep fingers behind the finger guards on the
probes.
• When the product has already been connected
to the line being measured, do NOT touch the
input terminal that is not in service.
• Disconnect the test leads from the circuit before
changing the mode.
• When the voltage to be measured exceeds 36V
DC or 25V AC, the operator shall be careful
enough to avoid electric shock.
• Misuse of mode or range can lead to hazards,
be cautious. “ ” will be shown on the display
when the input is out of range.
• Low level of a battery will result in incorrect
readings. Change the batteries when battery
level is low. Do not make measurements when
the battery door is not properly placed.
2
Содержание
- User manual 1
- And limitation of liability 2
- Customers enjoy one year warranty 2
- Disposable batteries damage from 2
- Limited warranty 2
- Lcd display 3
- Measurements instruction 0 3
- Table of contents page 3
- Test ncv 15 3
- Specifications 8 4
- Allowable measuring range 5
- Introduction 5
- Personal injury please read all safety information 5
- Rms a lcd display and a backlight 5
- Safety information 5
- To the line being measured do not touch the 6
- When the input is out of range 6
- Instrument overview 7
- ⑥ diode test 7
- Sinusoidal and nonsinusoidal ac 8
- ⑲ alternating current 8
- Backlight long push again to turn off or the 9
- Dc ma ac ma 9
- Selects alternate measurement modes on a 9
- Mode push the button for more than 2 10
- The product will store the present reading as 10
- Button when turning on the 11
- Power off press the select 11
- Turn off the product at this position 11
- Dc a from 199 9ma 12
- Duty cycle from 1 99 12
- Input terminal for the measurements of 13
- Measurements instruction 14
- The circuit to measure the voltage 14
- Measure resistance 15
- Touch the probes to the desired test points of 15
- Test diodes 16
- Turn the rotary switch to press select 16
- Display reading shows 17
- Three times to toggle to the capacitance mode 17
- Display 19
- Turn the rotary switch to press select 19
- Are qualified to do so and have the relevant 20
- Be replaced as below 20
- Clean the product 20
- Maintenance 20
- Loosen the four screws on the back cover and 21
- Of the same type 21
- Specifications 22
- 9mv 0 1mv 23
- Electrical specifications 23
- Mv 0 01mv 23
- 0 3 19 99kω 0 01kω 24
- Μa 0 μa 24
- Function range resolution accuracy 25
- Hz 0 hz 25
- Function range resolution accuracy 26
Похожие устройства
- Zotek ZT-102 Инструкция по эксплуатации
- Zotek ZT-M1 Инструкция по эксплуатации
- Zotek ZT-109 Инструкция по эксплуатации
- Zotek ZT-A6 Инструкция по эксплуатации
- Zotek ZT-98 Инструкция по эксплуатации
- Zotek ZT-100 Инструкция по эксплуатации
- Zotek ZT-101 Инструкция по эксплуатации
- Zotek ZT-C1 Инструкция по эксплуатации
- Zotek ZT-C2 Инструкция по эксплуатации
- Zotek ZT-C3 Инструкция по эксплуатации
- Zotek ZT-C4 Инструкция по эксплуатации
- Zotek ZT-S2 Инструкция по эксплуатации
- Yli Electronic YK-1068B Спецификация
- Zotek ZT-S3 Инструкция по эксплуатации
- Zotek ZT-S4 Инструкция по эксплуатации
- Zotek ZT-301 Инструкция по эксплуатации
- Yli Electronic YD-605 Спецификация
- Zotek ZT-302 Инструкция по эксплуатации
- Yli Electronic YM-280NT(LED) Спецификация
- Zotek VC15B+ Инструкция по эксплуатации