Maxwell MW-1183 BK [12/44] English

Maxwell MW-1183 BK [12/44] English
12
ENGLISH
12
Use the detachable cup (18) as a food con-
tainer. Make sure that the lids (17 and 19) are
closed tightly and the cover (20) is closed till the
clamp clicking. When carrying the cup (18) filled
with the liquid, hold it strictly in vertical position
(the cover (20) is on the top).
Note:
The level of products in the containers (5, 11,
16 and 18) should not exceed the maximal
level mark:
Chopper cup (5) – 1000 ml,
Detachable cup (18) – 500 ml,
Coffee grinder bowl (16) – 200 ml,
Chopper bowl – 300 ml.
Note:
For the consumer safety the unit is equipped
with special protection system that blocks
the unit if the containers (5, 11, 16, 18) are
set improperly on the motor unit. See the
corresponding chapter for recommenda-
tions for proper container (5, 11, 16, 18)
installation.
Operation modes:
Select the operation mode using the switch (2):
«1» (low speed) – for mixing of liquid products;
«2» (high speed)for liquid and hard products;
«P» (pulse mode) for processing of hard
products and ice.
Note: For operation in pulse mode turn the
switch (2) to the left and hold it.
To switch the unit off set the switch to the posi-
tion «0».
USING THE CHOPPER CUP (5)
WARNING:
Fix the knives block (4) in the base (3) and
install them into the chopper cup (5) before
using the unit. Make sure that all the details
are fixed properly.
Before installing the blender on the motor
unit make sure that the power plug is not
inserted into the socket.
1. Make sure that the sealing gasket is set on
the knives block (4).
2. Carefully install the knives block (4) into the
base (3) from the side of the thread till bump-
ing. Be very careful, the knife blades are
very sharp!
3. Place the cup (5) on the base (3) and rotate
the base (3) clockwise until bumping. To
avoid damages do not apply excessive effort
while tightening.
4. Set the chopper cup (5) on the motor unit (1).
To do this match ledges on the lower part of
the cup with grooves on the motor unit, press
on the cup and turn it clockwise till locking.
5. Put the food into the chopper cup (5).
6. Fix the plug cup (7) in the lid (6) opening:
insert till bumping and turn till locking.
7. Install the lid (6) on the chopper cup (5) so
the arrow on the lid is to the left from the
spout. Then turn the lid clockwise till lock-
ing, the arrow and the lid (6) openings will be
opposite the spout.
8. Insert the power plug into the mains socket.
9. Select the operation mode using the switch
(2).
10. During the operation you can add the
required ingredients through the lid (6) open-
ing after removing the plug cup (7).
11. After the unit operation, switch the unit off
and unplug it.
12. Remove the chopper cup (5) from the motor
unit (1) by pressing on it and turning it coun-
terclockwise.
13. Remove the lid (6) turning it counterclock-
wise and remove the products.
14. Clean the unit.
Note:
Products should be put into the chopper cup
before the unit is switched on. The level of
the products to process should not exceed
the maximal volume 1000 ml.
Attention! Do not remove the chopper cup
from the motor unit during operation.
USING THE FILTER (8)
1. Make sure that the silicone gasket is installed
on the knives block (4).
2. Carefully install the knives block (4) into the
base (3) from the side of the thread till bump-
ing. Be very careful, the knife blades are
very sharp!
3. Install the cup (5) on the base (3) and turn
till locking.
4. Set the chopper cup (5) on the motor unit
(1). To do this match ledges on the lower
part of the cup with grooves on the motor
unit, press on the cup and turn it clockwise
till locking.
5. Install the filter (8) into the cup (5) with wide
side down. The grooves of the filter should
match the guideways inside the cup.
6. Install the lid (6) on the cup (5) in such way
that the arrow on the lid is to the left from the
MW-1183.indd 12 20.02.2014 15:48:26
Скачать
Случайные обсуждения