Maxwell MW-1183 BK [13/44] English

Maxwell MW-1183 BK [13/44] English
13
ENGLISH
spout. Then turn the lid clockwise till locking,
the arrow will be opposite the spout.
7. Insert the power plug into the mains socket.
8. Select the operation mode using the switch
(2).
9. Add the fruit pieces or berries through the lid
(6) opening and press them with the pusher
(9). Check the pulp level inside the filter (8).
During the operation it should not exceed the
upper level of the mesh.
10. After the unit operation, switch the unit off
and unplug it.
11. Remove the chopper cup (5) from the motor
unit (1) by pressing on it and turning it coun-
terclockwise.
12. Pour the juice into suitable container without
removing the lid (6).
13. Remove the lid (6) preliminary turning it
counterclockwise.
14. Tamp the pulp with the pusher (9) and pour
out the remaining liquid.
15. Remove the filter (8) and clean the unit.
«Nut milk» recipe
Nut milk is made of preliminary prepared nuts
(almond, hazelnuts, cashew, walnut) or seeds
(shelled sunflower seeds, pumpkin seeds) and
water. Take water and nuts/seeds in proportion
3:1 (3 portions of water per 1 portion of nuts).
1. Wash the nuts/seeds and soak them in clean
drinking water for at least 12 hours.
2. Wash and peel the prepared nuts.
3. Follow the steps 1-6 of the chapter «Using
the filter».
4. Add nuts through the lid (6) opening (no more
the 1,5 measuring cup (7)).
5. Fill the tank with water.
6. Fix the measuring cup (7) in the lid (6).
7. Insert the power plug into the socket and
switch the unit on with the switch (2).
8. In 1 minute switch the unit off and unplug it.
9. Remove the chopper cup (5) from the motor
unit (1) by pressing on the cup (5) and turn-
ing it counterclockwise.
10. Pour the liquid into suitable container without
removing the lid (6).
11. Remove the lid (6) preliminary turning it
counterclockwise.
12. Tamp the pulp with the pusher (9) and pour
out the remaining liquid.
13. Remove the filter (8) and clean the unit.
Note: Process no more than 1,5 measuring
cup (7) of nuts/seeds at a time.
USING THE DETACHABLE CUP (18)
WARNING:
Fix the knives block (4) in the base (3) and
install them into the cup (18) before using the
unit. Make sure that all the details are fixed
properly.
Before installing the cup on the motor unit,
make sure that the power plug is not inserted
into the socket.
1. Make sure that the sealing gasket is set on
the knives block (4).
2. Carefully install the knives block (4) into the
base (3) on the side of the screw thread
till bumping. Be very careful, the knife
blades are very sharp!
3. Unscrew the lid (17) of the cup (18) turning it
counterclockwise.
4. Install the cup (18) on the base (3) and screw
till bumping.
5. Unscrew the lid (19) turning it counterclock-
wise.
6. Add the products into the cup (18).
7. Screw the lid (19) turning it clockwise. Close
the cover (20) until click.
8. Install the cup (18) attached to the base (3)
on the motor unit (1). To do this match ledges
on the lower part of the cup with grooves on
the motor unit, press on the cup and turn it
clockwise till locking.
9. Insert the power plug into the mains socket.
10. Select the operation mode using the switch (2).
11. After the unit operation, switch the unit off
and unplug it.
12. Remove the cup (18) from the motor unit (1) by
pressing on it and turning it counterclockwise.
13. Make sure that the lid (19) is fixed properly
and the cover (20) is closed. Turn the cup
(18) with its bottom up, holding the cover
(20) with your hand. Unscrew the base (3) by
rotating it counterclockwise.
14. Place the lid (17) on the cup (18) turning it
clockwise until bumping. Make sure that no
liquid leaks from the cup (18) through the
cover (20)
15. Carry the cup in vertical position with the
cover (20) up.
Notes:
Maximal volume of the products to process
should not exceed 500 ml.
Hold the cover (20) with your hand when
turning the cup with its lid (19) down.
Attention! Do not remove the cup from the
motor unit during the operation.
MW-1183.indd 13 20.02.2014 15:48:27
Скачать
Случайные обсуждения