Skil 0770 RT [8/96] Application advice
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Skil 0770 RT [8/96] Application advice

Skil 0770 RT [8/96] Application advice
8
• Store the tool indoors in a dry and locked-up place, out
of reach of children
BEFORE USE
• Check that all screws, nuts, bolts and other fasteners are
properly secured and that guards and screens are in
place
• Ensure that the feed intake is empty
DURING USE
• Keep your face and body away from the feed intake
opening
• Do not allow hands (or any other part of the body) or
clothing inside the feed intake opening, outlet opening or
near any moving part
• Keep proper balance and footing at all times; do not
overreach
• Never stand at a higher level than the base of the tool
when feeding material
• Always keep proper distance from the outlet zone when
operating the tool
• When feeding material into the tool be extremely careful
that pieces of metal, rocks, bottles, cans or other foreign
objects are not included
• If the cutting mechanism strikes any foreign object or if
the tool should start making any unusual noise or
vibration, immediately switch o, allow the cutting blade
to stop, disconnect the plug and take the following steps
- inspect for damage
- replace or repair any damaged parts
- check for and tighten any loose parts
• Do not allow processed material to build up in the outlet
zone; this may prevent proper discharge which can result
in kickback of material through the feed intake opening
• If the tool becomes clogged, switch o, allow the cutting
blade to stop and disconnect the plug before clearing
debris
• Keep the motor cooling vents clean of debris and other
accumulations to prevent damage to the motor or
possible re
• Do not tilt or transport the tool while the motor is running
WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
• Do not connect the blue (= neutral) or brown (= live) wire
in the cord of this tool to the earth terminal of the plug
• If for any reason the old plug is cut o the cord of this tool,
it must be disposed of safely and not left unattended
USE
• Assembly instructions $
- mount wheels with the two wrenches A supplied and
assemble tool as illustrated
- position collection bag B underneath outlet C
- mount prodder holder D
• On/o %
- switch on/o the tool by pushing switch E in “I”/”O”
position
! afterswitchingoffthetoolthebladecontinuesto
rotateforafewseconds
- allow the cutting blade to stop rotating before
switching on again
! thetoolwillnotstartunlesssecuringknobFis
fullytightened
! donotrapidlyswitchonandoff
• Restart protection
- after a power supply failure the tool will not restart on
its own
- use switch E % for restarting the tool
• Overload protection
Overloading (e.g. blocking up the cutting blade) can lead
to a standstill of the tool
- wait a short period before switching on the tool again
- restart tool by rst pushing button G % and then
switch E %
• Shredding ^
- feed the material to be chopped through feed intake
opening H
- only insert as much material so that the feed intake will
not be blocked up
! longermaterialcouldlashoutwhenbeingcut
! smallpiecesofshreddedmaterialmaybeejected
fromthefeedintakeopening
! wearsafetyglasses,hearingprotectionand
protectivegloveswhenusingthetool
- do not ll soft waste such as kitchen rubbish into the
shredder
- ensure that the chopped material can fall freely from
outlet C
- ensure that ventilation slots J 2 will not be covered by
the collection bag or the chopped material
- avoid blocking outlet C with shredded material as this
could result in kickback of material through feed intake
opening H
• Removing blockage &
! switchoffthetoolanddisconnecttheplug
- loosen securing knob F and open the tool as illustrated
- clean the blade area (remove compacted debris with a
woorden or plastic implement)
- also clean outlet C of any debris
- close the tool and tighten securing knob F rmly
• Reversing/changing cutting blade *
! switchoffthetoolanddisconnecttheplug
- the cutting blade has a cutting edge on both sides; so
if one side has become blunt, the other side can be
used
- replace the cutting blade when both sides are blunt
(SKIL spare part number 2610Z02553, marked YAT
8231-545201)
- loosen securing knob F and open the tool as illustrated
- loosen both blade bolts with hex key L while using
metal plate M as support
- reverse and mount the cutting blade as illustrated
- tighten both blade bolts with hex key L while using
metal plate M as support
- close the tool and tighten securing knob F rmly
APPLICATION ADVICE
• For best results shred fresh branches soon after they
have been cut
• Use prodder K for feeding soft material (
• Shred soft garden waste in smaller loads, particularly
when wet
• Blockages can be avoid by intermittently shredding
branches

Содержание

Похожие устройства

Store the tool Indoors In a dry and locked up place out of reach of children Restart protection after a power supply failure the tool will not restart on its own use switch E for restart ng th e tool Overload protection Overloading e g blocking up the cutting blade can lead to a standstill of the tool wait a short period before switching on the tool again restart tool by first pushing button G and then switch E Shredding feed the material to be chopped through feed intake opening H only insert as much material so that the feed intake will not be blocked up BEFORE USE Check that all screws nuts bolts and other fasteners are properly secured and that guards and screens are in place Ensure that the feed intake is empty DURING USE Keep your face and body away from the feed intake opening Do not allow hands or any other part of the body or clothing inside the feed intake opening outlet opening or near any moving part Keep proper balance and footing at all times do not overreach Never stand at a higher level than the base of the tool when feeding material Always keep proper distance from the outlet zone when operating the tool When feeding material into the tool be extremely careful that pieces of metal rocks bottles cans or other foreign objects are not included If the cutting mechanism strikes any foreign object or if the tool should start making any unusual noise or vibration immediately switch off allow the cutting blade to stop disconnect the plug and take the following steps inspect for damage replace or repair any damaged parts check for and tighten any loose parts Do not allow processed material to build up in the outlet zone this may prevent proper discharge which can result in kickback of material through the feed intake opening If the tool becomes clogged switch off allow the cutting blade to stop and disconnect the plug before clearing debris Keep the motor cooling vents clean of debris and other accumulations to prevent damage to the motor or possible fire Do not tiltor transport the tool while the motor is running WHEN CONNECTING NEW 3 PIN PLUG U K ONLY Do not connect the blue neutral or brown live wire in the cord of this tool to the earth terminal of the plug If for any reason the old plug is cut off the cord of this tool it must be disposed of safely and not left unattended I longer material could lash out when being cut small pieces of shredded material may be ejected from the feed intake opening I wear safety glasses hearing protection and protective gloves when using the tool do not fill softwaste such as kitchen rubbish into the shredder ensure that the chopped material can fall freely from outletC ensure that ventilation slots J will not be covered by the collection bag or the chopped material avoid blocking outlet C with shredded material as this could result in kickback of material through feed intake opening H Removing blockage switch off the tool and disconnect the plug loosen securing knob F and open the tool as illustrated clean the blade area remove compacted debris with a woorden or plastic implement also clean outlet C of any debris close the tool and tighten securing knob F firmly Reversing ch anging cutting bl ade switch off the tool and disconnect the plug the cutting blade has a cutting edge on both sides so if one side has become blunt the other side can be used replace the cutting blade when both sides are blunt SKIL spare part number 2610Z02553 marked YAT 8231 545201 loosen securing knob F and open the tool as illustrated loosen both blade bolts with hex key L while using metal plate M as support reverse and mount the cutting blade as illustrated tighten both blade bolts with hex key Lwhile using metal plate M as support close the tool and tighten securing knob F firmly USE Assembly instructions mount wheelswith the two wrenches A supplied and assemble tool as illustrated position collection bag B underneath outlet C mount prodder holder D On off switch on off the tool by pushing switch E in T O position APPLICATION ADVICE For best results shred fresh branches soon after they have been cut Use prodder K for feeding soft material Shred soft garden waste in smaller loads particularly when wet Blockagescan be avoid by intermittently shredding branches after switching off the tool the blade continues to rotate for a few seconds allow the cutting blade to stop rotating before switching on again the tool will not start unless securing knob F Is fully tightened I do not rapidly switch on and off 8

Скачать