![AMERICAN DJ Focus Spot THREE Z [14/20] Pro default](/img/pdf.png)
AMERICAN DJ Focus Spot THREE Z [14/20] Pro default
![AMERICAN DJ Focus Spot THREE Z [14/20] Pro default](/views2/2008199/page14/bge.png)
ADJ Products, LLC - www.adj.com - Focus Spot Three Z Instruction Manual Page 26 ADJ Products, LLC - www.adj.com - Focus Spot Three Z Instruction Manual Page 27
Focus Spot Three Z System Menu
Fixture Temp. - With this function you can display the
running temperature of the unit.
1. Press the MENU button until “Fixture Temp.” is displayed,
press ENTER.
2. The current running temperature of the xture will now be
displayed. Press MENU to exit.
Fixture Time - With this function you can display the
running time of the unit.
1. Press the MENU button until “Fixture Time” is displayed,
press ENTER.
2. The running time of the xture will now be displayed. Press
MENU to exit.
Firmware Version - This will display the rmware/soft-
ware version
1. Press the MENU button until “Firmware Version” is displayed.
Press the ENTER button and the rmware/software vesion will
be displayed.
2. Press the MENU button to leave this function.
PRO Defaults - This function will restore all factory
settings.
1. Press the MENU button until “PRO defaults” is displayed,
press ENTER. Either “Yes” or “No” will be displayed.
2. To restore factory settings press the UP or DOWN buttons
until “Yes” is displayed, press ENTER to conm. If you do not
wish restore the settings, select “No” and press Enter.
Reset - Use this function to reset the motors.
1. Press the MENU button until “Reset” is displayed, press
ENTER.
2. The xture will now reset.
Focus Spot Three Z System Menu
Содержание
- User instructions p.1
- Focus spot three z p.1
- Warning p.2
- Unpacking p.2
- Introduction p.2
- Customer support p.2
- Caution p.2
- Power supply p.5
- Dmx 512 p.5
- Some manufactures use 5 pin dmx 512 data cables for data transmission in place of 3 pin 5 pin dmx fixtures may be implemented in a 3 pin dmx line when inserting stan dard 5 pin data cables in to a 3 pin line a cable adaptor must be used these adaptors are readily available at most electric stores the chart below details a proper cable conversion p.6
- Pin xlr to 5 pin xlr conversion p.6
- Pin xlr dmx connectors p.6
- Pin 5 do not use p.6
- Pin 4 do not use p.6
- Notice p.6
- Not used p.6
- Lighting stores your cables should be made with a male and female xlr connector on either end of the cable also remember that dmx cable must be daisy chained and cannot be split p.6
- Ground shield p.6
- Focus spot three z dmx set up p.6
- Data true signal p.6
- Data compliment signal p.6
- Conductor 5 pin xlr male in 3 pin xlr female out p.6
- Be sure to follow figures two and three when making your own cables do not use the ground lug on the xlr connector do not con nect the cable s shield conductor to the ground lug or allow the shield conductor to come in contact with the xlr s outer casing grounding the shield could cause a short circuit and erratic behavior p.6
- When longer runs of cable are used you may need to use a terminator on the last unit to avoid erratic behavior a terminator is a 110 120 ohm 1 4 watt resistor which is con nected between pins 2 and 3 of a male xlr connector data and data this unit is inserted in the female xlr connector of the last unit in your daisy chain to terminate the line using a cable terminator adj part number z dmx t will decrease the possibilities of erratic behavior p.6
- Special note line termination p.6
- Focus spot three z 18 channel mode p.7
- Channel value function p.7
- Gobo wheel 2 p.8
- Gobo wheel 1 p.8
- Gobo 6 p.8
- Gobo 5 gobo 4 p.8
- Gobo 3 gobo 2 p.8
- Gobo 1 gobo 7 gobo 6 gobo 5 gobo 4 gobo 3 gobo 2 p.8
- Gobo 1 p.8
- Focus spot three z 18 channel mode p.8
- Channel value function p.8
- Focus spot three z 21 channel mode p.9
- Channel value function p.9
- Channel value function p.10
- Gobo wheel 2 p.10
- Gobo wheel 1 p.10
- Gobo 6 p.10
- Gobo 5 gobo 4 p.10
- Gobo 3 gobo 2 p.10
- Gobo 1 gobo 7 gobo 6 gobo 5 gobo 4 gobo 3 gobo 2 p.10
- Gobo 1 p.10
- Focus spot three z 21 channel mode p.10
- Slave mode p.11
- Dmx addres p.11
- Channel mod p.11
- Sound stat p.12
- Sound sens p.12
- Show mod p.12
- Dmx last stat p.12
- Dimmer curv p.12
- Zoom mod p.13
- Tilt inver p.13
- Pan inver p.13
- Manual tes p.13
- Function dela p.13
- Back ligh p.13
- Auto tes p.13
- Pro default p.14
- Fixture tim p.14
- Fixture temp p.14
- Firmware versio p.14
- Gobo 2 offse p.15
- Gobo 1 offse p.15
- Color offse p.15
- Adjustment of the tilt home position p.15
- Adjustment of the pan home position p.15
- Tilt offse p.15
- Setting adjustment for the color wheel p.15
- Setting adjustment for the 2nd gobo wheel p.15
- Setting adjustment for the 1st prism p.15
- Setting adjustment for the 1st gobo wheel p.15
- Prism 1 offse p.15
- Pan offse p.15
- Sound active mode p.16
- Show mode p.16
- Setting adjustment for the zoom p.16
- Setting adjustment for the rotating prism p.16
- Setting adjustment for the focus p.16
- Setting adjustment for the 2nd prism p.16
- Rprism offse p.16
- Prism 2 offse p.16
- Focus offse p.16
- Zoom offse p.16
- Universal dmx control p.16
- Master slave operation p.17
- Trouble shooting listed below are a few common problems that you may encounter with solutions p.19
- No light output from the unit p.19
- Low frequencies bass should cause the unit to react to sound tapping on the microphone quiet or high pitched sounds may not activate the unit p.19
- Locate and remove the unit s powercon cord once the cord has been removed the fuse holder is located next to the power socket use a philips head screw driver unscrew the fuse holder remove the bad fuse and replace with a new one p.19
- Focus spot three z warranty p.19
- Focus spot three z trouble shooting p.19
- Focus spot three z fuse replacement p.19
- Focus spot three z cleaning p.19
- Due to fog residue smoke and dust cleaning the internal and exter nal optical lenses and mirror should be carried out periodically to optimize light output cleaning frequency depends on the environ ment in which the fixture operates i e smoke fog residue dust dew in heavy club use we recommend cleaning on a monthly basis periodic cleaning will ensure longevity and crisp output 1 use normal glass cleaner and a soft cloth to wipe down the out side casing 2 use a brush to wipe down the cooling vents and fan grill 3 clean the external optics with glass cleaner and a soft cloth every 20 days 4 clean the internal optics with glass cleaner and a soft cloth every 30 60 days 5 always be sure to dry all parts completely before plugging the unit back in p.19
- Be sure the external fuse has not blown the fuse is located on the rear panel of the unit 2 be sure the fuse holder is completely and properly seated unit does not respond to sound p.19
- Adj products llc www adj com focus spot three z instruction manual page 36 adj products llc www adj com focus spot three z instruction manual page 37 p.19
- Adj products llc 6122 s eastern ave los angeles ca 90040 usa tel 323 582 2650 fax 323 725 6100 web www adj com e mail info americandj com p.20
- A d j supply europe b v junostraat 2 6468 ew kerkrade the netherlands service adjgroup eu www adj eu tel 31 45 546 85 00 fax 31 45 546 85 99 p.20
- This fixture contains a automatic volt age switch which will auto sense the voltage when it is plugged into the power source p.20
- Specifications and improvements in the design of this unit and this manual are subject to change without any prior written notice p.20
- Please note p.20
- Model focus spot three z p.20
- Auto sensing voltage p.20
Похожие устройства
-
AMERICAN DJ Dotz TPAR SystemРуководство по эксплуатации -
ADJ Hydro Beam X1Руководство по эксплуатации -
Involight LDF100Руководство по эксплуатации -
AMERICAN DJ Focus Spot ONEРуководство по эксплуатации -
Involight LED PAR984WРуководство по эксплуатации -
Antari M-7Руководство по эксплуатации -
STAGG SLI KINGPAR22Руководство по эксплуатации -
ADJ Par Z MoveРуководство по эксплуатации -
Involight LED ARCH2410Руководство по эксплуатации -
ADJ Micro Royal GalaxianРуководство по эксплуатации -
STAGG SLR LITE 1-2 BLРуководство по эксплуатации -
Involight LED PAR993WРуководство по эксплуатации