![AMERICAN DJ Vizi BSW300 [13/22] System menu when making adjustments press enter to confirm your setup then press and hold the menu button for at least 3 seconds to exit without making any adjust ments press the menu button the display will lock after 30 seconds press the menu button for 3 seconds to unlock](/img/pdf.png)
AMERICAN DJ Vizi BSW300 [13/22] System menu when making adjustments press enter to confirm your setup then press and hold the menu button for at least 3 seconds to exit without making any adjust ments press the menu button the display will lock after 30 seconds press the menu button for 3 seconds to unlock
![AMERICAN DJ Vizi BSW300 [13/22] System menu when making adjustments press enter to confirm your setup then press and hold the menu button for at least 3 seconds to exit without making any adjust ments press the menu button the display will lock after 30 seconds press the menu button for 3 seconds to unlock](/views2/2009553/page13/bgd.png)
ADJ Products, LLC - www.adj.com - Vizi BSW 300 Instruction Manual Page 25ADJ Products, LLC - www.adj.com - Vizi BSW 300 Instruction Manual Page 24
Vizi BSW 300 System Menu
System Menu: When making adjustments press ENTER to
conrm your setup then press and hold the MENU button
for at least 3 seconds. To exit without making any adjust-
ments press the MENU button. The display will lock after 30
seconds, press the MENU button for 3 seconds to unlock.
DMX SETTINGS -
DMX Address - With this function, you can adjust the desired DMX-
address via the Control Board.
1. Access the main menu, and press the UP or DOWN buttons so
that “DMX Setting” is highlighted, then press ENTER.
2. Press the UP or DOWN buttons until “DMX Address” is displayed,
and press ENTER. The current DMX address will now be displayed.
3. Use the UP or DOWN buttons to adjust the DMX address.
4. Press ENTER to conrm or press MENU button to return to the
main menu.
DMX Channel Mode - With this function, you can select your desired
DMX channel mode.
1. Access the main menu, and press the UP or DOWN buttons so
that “DMX Setting” is highlighted, then press ENTER.
2. Press the UP or DOWN buttons until “DMX Channel Mode” is dis-
played, and press ENTER. The current DMX channel mode will now
be displayed.
3. Press the MENU button to return to the main menu.
DMX State - This mode can be used as a precaution mode, that
in case the DMX signal is lost, interrupted, or power is lost, the
operating mode chosen in this setup is the running mode the
xture will go into when the DMX signal is lost. You can also
set this as the running mode you would like the unit to return to
when power is applied.
1. Access the main menu, and press the UP or DOWN buttons so
that “DMX Setting” is highlighted, then press ENTER.
2. Press the UP or DOWN buttons until “DMX State” is displayed,
and press ENTER. Use the UP and DOWN buttons to switch between
the two modes; Blackout or Hold. Press the ENTER button to make
your selection.
• LAST STATE - If the DMX signal is lost the xture will stay in the
last DMX setting. If power is applied and this mode is set, the unit will
automatically go into the last DMX set up.
• BLACKOUT - If the DMX signal is lost or interrupted, the unit will
automatically go into stand by mode.
• MASTER/SLAVE - If the DMX signal is lost or power is applied, the
unit will automatically go into Master Slave mode and run a built-in
show.
3. Press the MENU button to return to the main menu.
SHOW SETTINGS -
Show Mode - Select a desired preset show to run.
1. Access the main menu, and press the UP or DOWN buttons so
that “Show Setting” is highlighted, then press ENTER.
2. Press the UP or DOWN buttons until “Show Mode” is displayed,
and press ENTER. The current setting will now be displayed.
3. Use the UP or DOWN buttons to nd your desired show. Shows
1-4 are factory shows, while Show 0 is a random show.
4. Press ENTER to conrm your selection or press the MENU button
to return to the main menu.
Slave Mode - Use this mode to set the unit as a “Master”, “Slave 1”
or “Slave 2”
1. Access the main menu, and press the UP or DOWN buttons so
that “Show Setting” is highlighted, then press ENTER.
2. Press the UP or DOWN buttons until “Slave Mode” is displayed,
and press ENTER. The current setting will now be displayed.
3. Use the UP or DOWN buttons to nd your desired setting. Select-
ing “Slave 2” will give the unit contrast movement to the “Master”:
Vizi BSW 300 System Menu
Содержание
- User instructions 1
- Vizi bsw 300 1
- Customer support 2
- Introduction 2
- Table of contents 2
- Unpacking 2
- Unpacking introduction customer support safety precautions features handling precautions registration mounting 9 cad drawing base layout 0 dmx set up 1 13 dmx control 4 dmx traits 5 22 system menu 3 31 offset menu 2 35 error information 5 dimmer curve chart 6 photometric chart 7 gobo replacement 8 fuse replacement 9 cleaning 9 trouble shooting 0 warranty 1 specifications 2 2
- Vizi bsw 300 2
- Warning 2
- Caution 4
- Dmx 512 6
- Power supply 6
- Be sure to follow figures two and three when making your own cables do not use the ground lug on the xlr connector do not con nect the cable s shield conductor to the ground lug or allow the shield conductor to come in contact with the xlr s outer casing grounding the shield could cause a short circuit and erratic behavior 7
- Conductor 5 pin xlr male in 3 pin xlr female out 7
- Data compliment signal 7
- Data true signal 7
- Either end of the cable also remember that dmx cable must be daisy chained and cannot be split 7
- Ground shield 7
- Not used 7
- Notice 7
- Pin 4 do not use 7
- Pin 5 do not use 7
- Pin xlr dmx connectors 7
- Pin xlr to 5 pin xlr conversion 7
- Some manufactures use 5 pin dmx 512 data cables for data transmission in place of 3 pin 5 pin dmx fixtures may be implemented in a 3 pin dmx line when inserting stan dard 5 pin data cables in to a 3 pin line a cable adaptor must be used these adaptors are readily available at most electric stores the chart below details a proper cable conversion 7
- Special note line termination 7
- Vizi bsw 300 dmx set up 7
- When longer runs of cable are used you may need to use a terminator on the last unit to avoid erratic behavior a terminator is a 110 120 ohm 1 4 watt resistor which is con nected between pins 2 and 3 of a male xlr connector data and data this unit is inserted in the female xlr connector of the last unit in your daisy chain to terminate the line using a cable terminator adj part number z dmx t will decrease the possibilities of erratic behavior 7
- Channel value function 8
- Description of the dmx traits description of the dmx traits 8
- Follow the instructions on page 24 to select your desired dmx channel mode and dmx address 8
- For help operating in dmx mode consult the manual included with your dmx controller 8
- Included with your dmx controller included with your dmx controller 8
- This function allows you to use a univer sal dmx 512 controller a dmx controller allows you to create unique programs tailored to your individual needs 1 the vizi bsw 300 has 2 dmx channel modes an 17 channel mode and 20 channel mode see pages 15 22 for detailed 8
- To control your fixture in dmx mode follow the set up procedures on pages 11 13 as well as the set up specifications that are 8
- Universal dmx control 8
- Use the controller s faders to control the various dmx fixture traits 5 for longer cable runs more than a 100 feet use a terminator on the last fixture 8
- Vizi bsw 300 17 channel mode 8
- Vizi bsw 300 dmx control 8
- Channel value function 9
- Vizi bsw 300 17 channel mode 9
- Aperture 1 aperture 3 aperture 2 10
- Channel value function 10
- Gobo 1 10
- Gobo 1 gobo 2 gobo 3 gobo 4 10
- Gobo 2 gobo 3 gobo 4 gobo 5 gobo 6 10
- Gobo 5 gobo 6 gobo 7 10
- Gobo wheel 1 10
- Gobo wheel 2 10
- Channel value function 11
- Vizi bsw 300 20 channel mode 11
- Channel value function 12
- Gobo 1 gobo 2 gobo 3 gobo 4 12
- Gobo 5 gobo 6 gobo 7 12
- Gobo wheel 1 12
- Gobo wheel 2 12
- System menu when making adjustments press enter to confirm your setup then press and hold the menu button for at least 3 seconds to exit without making any adjust ments press the menu button the display will lock after 30 seconds press the menu button for 3 seconds to unlock 13
- This mode can be used as a precaution mode that in case the dmx signal is lost interrupted or power is lost the operating mode chosen in this setup is the running mode the fixture will go into when the dmx signal is lost you can also set this as the running mode you would like the unit to return to when power is applied 13
- Adjustment of the pan home position 17
- Adjustment of the tilt home position 17
- R gobo 17
- Setting adjustment for color wheel 1 17
- Setting adjustment for color wheel 2 17
- Setting adjustment for gobo wheel 1 glass gobo wheel 17
- Setting adjustment for the gobo wheel 1 glass gobo wheel 17
- Angle fros 18
- R pris 18
- Setting adjustment for gobo wheel 2 18
- Setting adjustment for the 1st prism 18
- Setting adjustment for the 2nd prism 18
- Setting adjustment for the focus 18
- Setting adjustment for the frost filter 18
- Setting adjustment for the rotating prism 18
- Adj products llc www adj com vizi bsw 300 instruction manual page 36 adj products llc www adj com vizi bsw 300 instruction manual page 37 19
- Vizi bsw 300 dimmer curve chart 19
- Vizi bsw 300 photometric chart 19
- Fixture cleaning 20
- Adj products llc www adj com vizi bsw 300 instruction manual page 40 adj products llc www adj com vizi bsw 300 instruction manual page 41 21
- Check the dmx connectors cables to see if they are linked prop erly 2 if the dmx led is on and no response to the channel check the address settings and the dmx controller polarity 21
- Check the power connection and main fuse 2 be sure the fuse holder is completely and properly seated 21
- Error warnings 21
- Interface circuit interface circuit 21
- Not responding to dmx control 21
- One of the channels is not working well 21
- See page 36 for error warnings contact adj customer service 21
- The motor s drive ic on the pcb might be out of condition 21
- The stepper motor might be damaged or the cable connected to the pcb is broken 21
- Trouble shooting listed below are a few common problems that you may encounter with solutions 21
- Try using another dmx controller 4 check to see if the dmx cables run near or run alongside to high voltage cable it may cause damage or interference to dmx 21
- Unit does not work no light output and the fan does not work 21
- Vizi bsw 300 trouble shooting 21
- Vizi bsw 300 warranty 21
- A d j supply europe b v 22
- Adj products llc 22
- Ew kerkrade 22
- Junostraat 2 22
- Model vizi bsw 300 22
- S eastern ave los angeles ca 90040 usa 22
- Service adjgroup eu www adj eu 22
- Tel 31 45 546 85 00 fax 31 45 546 85 99 22
- Tel 323 582 2650 fax 323 725 6100 22
- The netherlands 22
- Web www adj com e mail info americandj com 22
Похожие устройства
- AMERICAN DJ Spherion WH LED Руководство по эксплуатации
- AMERICAN DJ Sparkle LED 3W Руководство по эксплуатации
- AMERICAN DJ Saturn TriLED SYS Руководство по эксплуатации
- AMERICAN DJ Revo Sweep Руководство по эксплуатации
- AMERICAN DJ Stinger Gobo Руководство по эксплуатации
- Arthur Forty U-9900B (UHF) Руководство по эксплуатации
- APart SDQ5PIR-BL Руководство по эксплуатации
- APart PMR4000RMKII Руководство по эксплуатации
- APart SDQ5PIR-W Руководство по эксплуатации
- APart OVO8-W Руководство по эксплуатации
- APart OVO8P-W Руководство по эксплуатации
- APart OVO8T-BL Руководство по эксплуатации
- American Audio VLP1500 Руководство по эксплуатации
- AMC HQ 10EN Руководство по эксплуатации
- ASHLY TRA-2150 Руководство по эксплуатации
- AMC HQ 15EN Руководство по эксплуатации
- ASHLY MX-508 Руководство по эксплуатации
- ASHLY MX-206 Руководство по эксплуатации
- ASHLY TRA-2075 Руководство по эксплуатации
- ELECTRO VOICE R300-E Руководство по эксплуатации