Tc Electronic G-SHARP [18/31] Operating input output section
![Tc Electronic G-SHARP [18/31] Operating input output section](/views2/1011819/page18/bg12.png)
16
OPERATING - INPUT/OUTPUT SECTION
INPUT GAIN & 1/L-2/R INPUT LEDs
This knob controls the input level for both the
analog and digital input options. A correctly set
input level is essential to achieve optimal
performance with least possible noise.
T
o set the Input level:
Clean sounds have the most dynamics. Play
powerful chords with the loudest clean sound
you use and adjust the Input Gain accordingly.
The Input LEDs indicate the level using three
colors.
Green : -40dB - You are “well on the safe
side”.
Yellow : -6dB - You are close to optimal
performance.
Red : -1dB - Red LED only blink
occasionally at absolute peaks.
Analog Input Range
Counter-clockwise : -10dB
Center : 0dB
Clockwise : +14dB
Digit
al Input Range
Counter-clockwise : -18dB
Center : 0dB
Clockwise : +6dB
Parallel mode/(serial mode) LED and button
Press the switch to switch between Serial and
Parallel modes. When this LED is lit (green)
Parallel mode is selected. When the LED is not
lit - Serial mode is selected.
EFFECTS MIX
Adjusts the mix between the wet and the dry
signal for the Effects engine.
REVERB MIX
Adjusts the mix between the wet and the dry
signal for the Reverb engine.
BYPASS LED
When the LED is lit, G-Sharp is in bypass
mode. The bypass function operates differently
depending on whether you are in Killdry mode
or not.
Killdry “on”:
The BYPASS key operates as a mute function.
Killdry “off”:
The bypass function simply passes the source
signal unprocessed to output.
Killdry ON LED
Killdry mode is selected on the rear panel.
When it is selected, no clean signal passes
through the G-Sharp. This is the setting to use
if you connect G-Sharp in a parallel loop or e.g.
in an aux send/return on a mixer.
Содержание
- Important safety instructions 3
- Important safety instructions 4
- Table of contents 5
- If you just can t wait 6
- Quick start 6
- Engine 1 7
- Engine 2 7
- Introduction 7
- Front panel overview 8
- Front panel overview 9
- Rear panel 10
- G sharp 11
- Signal flow 11
- Basics 12
- Connecting and setting up the g sharp 12
- Controlling g sharp 12
- Routings 12
- Basics 13
- By the effects engine serial mode works perfectly for all effect combinations but if you are using relatively long and loud delay repeats you should consider whether you prefer to have reverb added to delay repeats or not if you prefer the delay repeats to stand out very clear and still use reverb you may prefer the parallel routing 13
- Effects 13
- General advice 13
- High quality cables good cables are essential we advice that you use properly shielded cables of high quality throughout your entire setup but be aware that one of the most sensitive points is the cable going from your guitar to the first piece of equipment especially if you are using a guitar with passive single coil pickups such as a stratocaster the few extra bucks for good quality cables are well spent 13
- Level settings correct level settings in all audio equipment are essential to get best performance from ad and da converters and as little noise as possible therefore you should follow the advice on setting input level as described on page 16 13
- Parallel routing analog input only this routing gives you the opportunity of having two effects in parallel even on a single mono signal the input signal is split and fed to both the effects engine and the reverb engine at the same time both the effects engine and the reverb engine uses left and right outputs as common outputs 13
- Reverb 13
- You cannot connect a guitar directly to the g sharp inputs always insert a preamp pedal or similar piece of equipment between the guitar and the g sharp 13
- Serial setup 14
- Typical setups 14
- Head cab 15
- Typical setups 15
- Preamp combo 16
- Typical setups 16
- Preamp power amp 17
- Typical setups 17
- Operating input output section 18
- Effects engine 19
- The effects engine 19
- The effects engine 20
- Reverb engine 21
- The reverb engine 21
- Display 22
- Load store presets 22
- Preset modes 22
- Store recall the g sharp display 22
- Miscellaneous 23
- Delay controls 24
- Delay spillover feature 24
- Delay types 24
- Effects 24
- Chorus 25
- Chorus flanger controls 25
- Effects 25
- Flange 25
- Phaser 25
- Phaser controls 25
- Tremolo 25
- Tremolo controls 25
- Vibrato 25
- Reverbs 26
- Reverbs 27
- Appendix 28
- Midi implementation chart 28
- Appendix 29
- Midi bulk dump 29
- Midi cc reset bulk dump 29
- Midi continuous controllers 29
- Reset procedure 29
- Troubleshooting 30
- Appendix 31
- Due to continuous development these specifications are subject to change without notice 31
- Technical specifications 31
Похожие устройства
- Casio EX-ZS10 Pink Инструкция по эксплуатации
- Champion 3053-C2 Инструкция по эксплуатации
- Toshiba SD-47HKSR Инструкция по эксплуатации
- Pandora программирование брелков Инструкция по эксплуатации
- Tc Electronic G-SYSTEM Инструкция по эксплуатации
- Hertz Hertz HE 2 Инструкция по эксплуатации
- Casio EX-ZS10 Silver Инструкция по эксплуатации
- Stiga Collector 46 B 299174621/S11 Инструкция по эксплуатации
- Bosch TWK 8611 Инструкция по эксплуатации
- Toshiba SD-44HKSE Инструкция по эксплуатации
- Pandora RX-100 (2004 г) Инструкция по эксплуатации
- Casio EX-ZS10 Blue Инструкция по эксплуатации
- Tc Electronic SCF Инструкция по эксплуатации
- Hertz HE 4 Инструкция по эксплуатации
- Bosch TWK 7007 Инструкция по эксплуатации
- MTD 46 SPO Инструкция по эксплуатации
- Toshiba SD-43HK Инструкция по эксплуатации
- Tc Electronic TRIPLE-C STEREO Инструкция по эксплуатации
- Pandora RX-100 (2006 г) Инструкция по эксплуатации
- Hertz Hertz HE 1D Инструкция по эксплуатации