Home
Главная
Stiga
Райдеры
PARK PRESTIGE 18 4WD
Инструкция по эксплуатации Страница: 65

Stiga PARK PRESTIGE 18 4WD [65/209] English

ENGLISH

can be found in the service log and the actions are

described under “4 STARTING AND OPERA-

TION” as well as below.

Servicing carried out at an authorised workshop

guarantees professional work using genuine spare

parts.

At each basic service and intermediate service car-

ried out at an authorised workshop, the service log

is stamped. A service log presenting these services

is a valuable document that improves the ma-

chine’s second-hand value.

5.2 PREPARATION

All service and all maintenance must be carried out

on a stationary machine with the engine switched

off.

Prevent the machine from rolling by al-

ways applying the parking brake.

Stop the engine.

Prevent unintentional starting of the

engine by disconnecting the spark plug

cable(s) from the spark plug(s) and re-

moving the ignition key.

5.3 TYRE PRESSURE

Adjust the air pressure in the tyres as follows:

Front: 0.6 bar (9 psi).

Rear: 0.4 bar (6 psi).

5.4 CHANGING ENGINE OIL

This section contains tables covering the different

engines that are included in STIGA’s range. To fa-

cilitate reading, mark the data that applies to the

relevant machine/engine.

5.4.1 Change intervals

The table below states hours of operation and cal-

endar months. Carry out the relevant action at

whichever occurs first.

Change the oil more frequently if the engine has to

operate in demanding conditions or if the ambient

temperature is high.

5.4.2 Engine Oil

Use oil according to the table below.

Use oil without any additives.

Do not fill with too much oil. This can cause the

engine to overheat.

Change oil when the engine is warm.

The engine oil may be very hot if it is

drained off directly after the engine is

shut off. Therefore allow the engine to

cool a few minutes before draining the

oil.

1. Attach the clamp on the oil drainage hose. Use

a polygrip or similar. See fig. 10-11:Y.

2. Move the clamp up 3-4 cm on the oil drainage

hose and pull out the plug.

3. Collect the oil in a collection vessel.

NOTE! Do not spill any oil on the drive belts.

4. Hand in the oil for disposal in accordance with

local provisions.

5. Install the oil drainage plug and move the clamp

back so that it clamps above the plug.

6. Remove the dipstick and fill with new oil.

Oil quantity:

7. After filling up the oil, start the engine and idle

for 30 seconds.

8. Check to see if there is any oil leakage.

9. Stop the engine. Wait for 30 seconds and then

check the oil level in accordance with 4.2.

5.4.3 Oil filter (Ranger Svan, Prestige)

First drain the engine oil and install the oil drain-

age plug as described above. Then replace the oil

filter as follows:

1. Clean the area around the filter and dismantle

the filter.

2. Moisten the new filter’s gasket with oil.

3. Install the filter. First screw in the filter so that

the gasket comes into contact with the engine.

Then screw in the filter a further 1/2-3/4 turn.

4. Continue with point 7 in accordance with 5.4.2

Engine Oil above.

Machine 1st time

Then at

intervals of

President, Residence,

Prestige (B&S)

Hours of operation/

Calendar months

Changing the oil 5 hours

50 hours/

12 months

Ranger Svan (Honda)

Hours of operation/

Calendar months

Changing the oil

20 hours/

1 month

100 hours/

6 months

Oil SAE 10W-30

Service class SJ or higher

Machine

Oil quantity, approximately

No filter

replacement

Filter replace-

ment

President,

Residence

1,4 litres -

Prestige 1,4 litres 1,5 litres

Ranger Svan 0,9 litres 1,05 litres

Stiga PARK PRESTIGE 18 4WD [65/209] English

Содержание

Похожие устройства