![Robomow RC302 Инструкция по эксплуатации онлайн [32/58] 157374](/img/pdf.png)
Robomow RC302 Инструкция по эксплуатации онлайн [32/58] 157374
![Robomow RC302 Инструкция по эксплуатации онлайн [32/58] 157374](/views2/1172599/page32/bg20.png)
31
EN
5.2.6 Test Wire
Position
• U003 is displayed (Test Wire Posion) – press OK.
• Robomow will follow the wire along the edge to test the
wire position.
Walk alongside Robomow while it is following the edge.
Having completed the process, Robomow will enter the
Base Station and the setup process will be completed.
If the mower collides with obstacles along the
edge, the mower will stop and drive backwards
with
‘
U052
’ (
Adjust Wire
)
displayed:
• Move the wire slightly inward.
• Press OK to continue the Wire Test.
• If, at any point, you wish the mower to drive closer to the
edge to enlarge the covered area, press Stop (‘U003’ is
displayed –
Test Wire Posion
):
- Move the wire slightly outward.
- Place the mower in front of the changed section of
wire.
- Press OK to continue the ‘‘Test Wire Position’ process.
• If you want to quit the setup process, press and hold the
STOP button for 3 seconds. The screen will change to
the Main Display (current time).
• After completing the Test Wire Position, test the mower
in Near Wire Follow mode to conrm it completes the
drive near the wire smoothly, without acquiring any
adjacent wire or hitting any obstacle on its way to the
Base Station.
• If the mower fails to complete the Near Wire Follow
smoothly to the Base Station, then reduce the Near Wire
Follow Distance (Menu P004) and repeat the test until it
will complete the drive smoothly.
!
IMPORTANT
!
To restart the One-Time Setup process press and hold STOP + Settings + Left
arrow buttons together for more than 4 seconds. This will invoke Factory Defaults (“Out of the
Box” settings).
5.2.7 After Setup is Completed
Once the wire setup is complete, drive additional pegs at a
distance of approximately 0.75 m (2.5 ft.) apart.
• Use additional pegs in areas where there are bumps or
dips in the lawn.
If needed, purchase extra pegs.
• Inspect the wire installation for tripping hazards.
From this point on Robomow is ready to be charged.
Once fully charged it will automatically mow your lawn.
Note!
The rst charging may take longer then usual (up to 24 hours).
Содержание
- Operation and safety manual 2
- Table of contents 3
- Chapter 1 4
- Important 4
- Introduction and safety 4
- 7 6 5 4 3 2 5
- Safety warnings precautions 5
- Warning decal definitions 5
- Robomow safety features 7
- Chapter 2 8
- Know your robomow 8
- What s in the box 8
- How robomow works for you 9
- Robomow features 10
- Chapter 3 11
- Lawn types what does your lawn look like 11
- Planning ahead 11
- Main sub zone with a narrow pass 12
- Main zone sub zone s type lawn 12
- Separated zone 12
- Separated zones type lawn 12
- A separated zone larger than 100 m² 1100 ft² 13
- A separated zone smaller than 100 m² 1100 ft² 13
- Base station location guidelines 13
- Select base station location 13
- Setups 13
- Types of separated zone 13
- At a corner 14
- External setup off the lawn perimeter 14
- Internal setup on the lawn perimeter 14
- Main zone 14
- Outside the lawn 14
- There are two types of external setup 14
- Objects inside 15
- Planning the perimeter wire layout 15
- Select power box location 15
- Slopes 15
- Distances from the edge pools ponds cliffs etc 16
- Interference with adjacent lawns 16
- Chapter 4 17
- Initial setup 17
- Perimeter wire setup 17
- Preparations 17
- Laying the perimeter wire 18
- Starting point perimeter wire at the base station area 18
- Important information 19
- Min 1 m 4ft 19
- Perimeter wire within the working area 20
- Main zone 21
- Min 50cm 21
- Sub zone 21
- Main zone 22
- Min 50cm 22
- Sub zone 22
- Fastening perimeter wire to the 23
- Ground 23
- Main zone 23
- Back at the base station completing the perimeter wire setup 24
- Connecting the power box 25
- Laying and fastening extension cable 25
- Placement and connection of the base station 25
- At the power box location 26
- Determining the perimeter switch location 27
- Laying out the perimeter wire 27
- Perimeter switch placing options 27
- Setup in a non base zone 27
- At the perimeter switch s location 28
- Chapter 5 30
- Preparing robomow 30
- No wire signa 31
- Peg bas 31
- Position 31
- Reposition base station 31
- Swap wires in plot connecto 31
- Area setting indicator 33
- Automatic operation 33
- Battery and charging indicator 33
- Chapter 6 33
- Day and time setting indicator 33
- Days of the week 33
- Inactive time setting indicator rain sensor 33
- Mower is in the base station indicator 33
- Mowing hours setting indicator 33
- Operating panel 33
- Red lit constantly low battery green blinking charging green lit constantly fully charged 33
- Robomow operation 33
- User error messages 33
- Chapter 6 34
- Robomow operation 34
- Basic settings 35
- Menu options 35
- Screen setting description options 36
- Screen setting description options 37
- Screen setting description options 38
- Screen setting description options 39
- Operation in a non base zone using a perimeter switch 40
- Robomow app settings 40
- Chapter 7 41
- Enable disable the automatic operation 41
- Event description 41
- Power box alerts 41
- Turn the buzzer on off 41
- Using the power box 41
- Chapter 8 42
- Charging 42
- Chapter 9 43
- General error codes 43
- Robomow error codes table 43
- Troubleshooting and user messages 43
- Display message probable cause event corrective actions 44
- Detailed error codes 45
- Display message probable cause event corrective actions 45
- Display message probable cause event corrective actions 46
- Display message description required action 47
- User messages 47
- Basic troubleshooting 48
- Display message description required action 48
- Problem encountered probable cause event corrective actions 48
- U090 u093 48
- Problem encountered probable cause event corrective actions 49
- Code description corrective action 50
- Description of no depart codes 50
- Anti theft disabling device pin code write down your 4 digit anti theft disabling device pin code refer here if you ever forget the code 51
- Chapter 10 51
- Product specification 51
- Rc304 rc308 rc312 51
- Robomow serial number 51
- _______________________ 51
- Chapter 11 52
- Maintenance and storage 52
- Maintenance of the blade 53
- Lightning storm 54
- Maintenance of the base station area 54
- Splicing the perimeter wire 54
- Accessories 55
- Chapter 12 55
- Chapter 13 56
- Robomow lawn care has never been so easy 56
- Tips for maintaining your lawn 56
- Always follow the safety instructions specified in this user manual 57
- C series limited warranty 57
- Warranty card 57
Похожие устройства
- Robomow RC302 Инструкция QuickStart
- Lenovo b5030, 59-430205 Инструкция по эксплуатации
- Robomow RC306 Инструкция по эксплуатации
- Robomow RC306 Инструкция QuickStart
- Lenovo b5030, 59-430218 Инструкция по эксплуатации
- Lenovo b5030, 59-430217 Инструкция по эксплуатации
- Robomow RL555 Инструкция по эксплуатации
- Robomow RL555 Инструкция QuickStart
- Lenovo b5030, 59-430203 Инструкция по эксплуатации
- Lenovo b5070, 59-435371 Инструкция по эксплуатации
- Robomow RL855 Инструкция по эксплуатации
- Lenovo b5070, 59-435821 Инструкция по эксплуатации
- Robomow RL855 Инструкция QuickStart
- Lenovo b5070, 59-435373 Инструкция по эксплуатации
- Lenovo b5070, 59-435372 Инструкция по эксплуатации
- Lenovo g5030, 80g0016nrk Инструкция по эксплуатации
- Lenovo g5030, 80g000xwrk Инструкция по эксплуатации
- Lenovo ideapad s2030, 59-436224 Инструкция по эксплуатации
- Lenovo ideapad s2030, 59-436222 Инструкция по эксплуатации
- Lenovo thinkpad x240, 20al00dmrt Инструкция по эксплуатации
Скачать
Случайные обсуждения