Mitsubishi Electric PURY-RP200YJM-A [9/31] Safety precautions

1.1. Before installation and electric work

X Before installing the unit, make sure you read all the

“Safety precautions”.

X The “Safety precautions” provide very important points

regarding safety. Make sure you follow them.

Symbols used in the text

Warning:

Describes precautions that should be observed to prevent danger of injury

or death to the user.

Caution:

Describes precautions that should be observed to prevent damage to the

unit.

Symbols used in the illustrations

: Indicates an action that must be avoided.

: Indicates that important instructions must be followed.

: Indicates a part which must be grounded.

: Beware of electric shock. (This symbol is displayed on the main unit

label.) <Color: yellow>

Warning:

Carefully read the labels afﬁ xed to the main unit.

HIGH VOLTAGE WARNING:

Control box houses high-voltage parts.

When opening or closing the front panel of the control box, do not let it

come into contact with any of the internal components.

Before inspecting the inside of the control box, turn off the power,

keep the unit off for at least 10 minutes, and conﬁ rm that the voltage

between FT-P and FT-N on INV Board has dropped to DC20V or less.

(It takes about 10 minutes to discharge electricity after the power

supply is turned off.)

Warning:

Ask the dealer or an authorized technician to install the air conditioner.

- Improper installation by the user may result in water leakage, electric

shock, or ﬁ re.

This appliance is not intended for use by persons (including children)

with reduced physical, sensory or mental capabilities, or lack of

experience and knowledge, unless they have been given supervision

or instruction concerning use of the appliance by a person responsible

for their safety.

Install the unit at a place that can withstand its weight.

- Failure to do so may cause the unit to fall down, resulting in injuries and

damage to the unit.

Use the speciﬁ ed cables for wiring. Make the connections securely so

that the outside force of the cable is not applied to the terminals.

- Inadequate connection and fastening may generate heat and cause a ﬁ re.

Prepare for strong winds and earthquakes and install the unit at the

speciﬁ ed place.

- Improper installation may cause the unit to topple and result in injury and

damage to the unit.

Always use ﬁ lters and other accessories speciﬁ ed by Mitsubishi Electric.

- Ask an authorized technician to install the accessories. Improper

installation by the user may result in water leakage, electric shock, or ﬁ re.

•

Never repair the unit. If the air conditioner must be repaired, consult

the dealer.

- If the unit is repaired improperly, water leakage, electric shock, or ﬁ re may

result.

If the supply cord is damaged, it must be replaced by the manufacturer,

its service agent or similarly qualiﬁ ed persons in order to avoid a

hazard.

Do not touch the heat exchanger ﬁ ns.

- Improper handling may result in injury.

If refrigerant gas leaks during installation work, ventilate the room.

- If the refrigerant gas comes into contact with a ﬂ ame, poisonous gases will

be released.

Install the air conditioner according to this Installation Manual.

- If the unit is installed improperly, water leakage, electric shock, or ﬁ re may

result.

Have all electric work done by a licensed electrician according

to “Electric Facility Engineering Standard” and “Interior Wire

Regulations” and the instructions given in this manual and always use

a dedicated power supply.

- If the power source capacity is inadequate or electric work is performed

improperly, electric shock and ﬁ re may result.

Securely install the outdoor unit terminal cover (panel).

- If the terminal cover (panel) is not installed properly, dust or water may

enter the outdoor unit and ﬁ re or electric shock may result.

When installing and moving the air conditioner to another site, do not

charge it with a refrigerant different from the refrigerant speciﬁ ed on

the unit.

- If a different refrigerant or air is mixed with the original refrigerant, the

refrigerant cycle may malfunction and the unit may be damaged.

If the air conditioner is installed in a small room, measures must be

taken to prevent the refrigerant concentration from exceeding the

safety limit if the refrigerant should leak.

- Consult the dealer regarding the appropriate measures to prevent the

safety limit from being exceeded. Should the refrigerant leak and cause

the safety limit to be exceeded, hazards due to lack of oxygen in the room

could result.

When moving and reinstalling the air conditioner, consult the dealer or

an authorized technician.

- If the air conditioner is installed improperly, water leakage, electric shock,

or ﬁ re may result.

After completing installation work, make sure that refrigerant gas is not

leaking.

- If the refrigerant gas leaks and is exposed to a fan heater, stove, oven, or

other heat source, it may generate noxious gases.

Do not reconstruct or change the settings of the protection devices.

- If the pressure switch, thermal switch, or other protection device is shorted

or operated forcibly, or parts other than those speciﬁ ed by Mitsubishi

Electric are used, ﬁ re or explosion may result.

To dispose of this product, consult your dealer.

The installer and system specialist shall secure safety against leakage

according to local regulation or standards.

- Choose the appropriate wire size and the switch capacities for the main

power supply described in this manual if local regulations are not available.

Pay special attention to the place of installation, such as a basement,

etc. where refrigeration gas can accumulate, since refrigerant is

heavier than the air.

For outdoor units that allow fresh air intake to the indoor unit, the

installation site must be carefully chosen to ensure only clean air can

enter the room.

- Direct exposure to outdoor air may have harmful effects on people or food.

Children should be supervised to ensure that they do not play with the

appliance.

•

1. Safety precautions

Contents

1. Safety precautions ....................................................................................... 9

1.1. Before installation and electric work ............................................ 9

1.2. Precautions for devices that use R410A refrigerant .................. 10

1.3. Before installation ...................................................................... 10

1.4. Before installation (relocation) - electrical work ......................... 10

1.5. Before starting the test run ........................................................ 10

2. About the product ....................................................................................... 10

3. Combination of outdoor units ......................................................................11

4. Speciﬁ cations ..............................................................................................11

5. Conﬁ rmation of parts attached ....................................................................11

6. Space required around unit .........................................................................11

7. Lifting method .............................................................................................11

8. Installation of unit ....................................................................................... 12

8.1. Installation ................................................................................. 12

9. Refrigerant piping installation ..................................................................... 12

9.1. Caution ...................................................................................... 12

9.2. Refrigerant piping system ........................................................ 13

10. Additional refrigerant charge ...................................................................... 13

10.1. Calculation of additional refrigerant charge ............................... 13

10.2. Precautions concerning piping connection and

valve operation .......................................................................... 14

10.3. Airtight test, evacuation, and refrigerant charging ..................... 15

10.4. Thermal insulation of refrigerant piping ..................................... 16

11. Wiring (For details, refer to the installation manual of each unit and

controller.) .................................................................................................. 16

11.1. Caution ...................................................................................... 16

11.2. Control box and connecting position of wiring ........................... 16

11.3. Wiring transmission cables ....................................................... 17

11.4. Wiring of main power supply and equipment capacity .............. 18

12. Test run ...................................................................................................... 19

12.1. The following phenomena do not represent faults. ................... 19

13. Information on rating plate ......................................................................... 19

Mitsubishi Electric PURY-RP200YJM-A [9/31] Safety precautions

Содержание

Похожие устройства