![Mono Omega Touch 400 [11/63] Cleaning instructions](/img/pdf.png)
Mono Omega Touch 400 [11/63] Cleaning instructions
![Mono Omega Touch 400 [11/63] Cleaning instructions](/views2/1334004/page11/bgb.png)
FG078 –OMEGA TOUCH LMC 09-12 RAC
11
7.0 CLEANING INSTRUCTIONS
NOTE:
- Cleaning must be carried out by fully trained personnel only.
- Isolate machine from mains supply before carrying out any cleaning.
- Do not steam clean or use a jet of water.
-Do not use any form of caustic detergent or abrasive cleaners.-
All the outer surfaces of the machine should be wiped over daily with warm soapy water.
HARD AND SOFT DOUGH HOPPERS
BETWEEN PRODUCT MIX CHANGES
The feed hopper, pump assembly, template, nozzles etc. should be removed from
the machine and dismantled for thorough cleaning between product mix changes.
1. Open top safety guard and remove excess mixture remaining in the feed hopper.
2. Lift off front see-through safety cover and locking-ring.
SAFETY COVER
LOCKING RING
Omega
Touch
Содержание
- Depositor 400 450 580 1
- Manual 1
- Omega touch 1
- Operating and maintenance 1
- Failure to adhere to the cleaning and maintenance instructions detailed in this booklet could affect the warranty of this machine 3
- Contents 4
- Maintenance 12 spares and service 13 spares list 14 electrical information 4
- Operating instructions 4
- Preparing for operation 4
- Introduction 5
- Dimensions 6
- Omega touch 6
- Specifications 7
- Safety 8
- All cleaning and maintenance operations must 9
- Be made with machine disconnected from the 9
- Power supply 9
- In an emergency switch off at the mains in an emergency switch off at the mains wall isolator or emergency stop button 10
- Installation 10
- Isolation 10
- Stop button 10
- To release the emergency stop button turn clockwise 10
- Cleaning instructions 11
- Hard and soft dough hoppers 11
- Soft dough hopper 13
- Do not leave any components in the hopper 14
- Hard dough hopper 14
- Operating conditions 15
- Preparing for operation 16
- A fitting the hopper 17
- Do not operate machine without template fitted 17
- B fitting a template soft dough 18
- Do not operate machine without template fitted 18
- Do not operate machine without template fitted 19
- Hard dough 19
- Omega touch operation 20
- Change settings 21
- For following instructions 21
- If a grey box is shown in the button description e g go to the corresponding page further on in the instructions marked in top right hand corner of each page 21
- Operating key 21
- Operation 21
- Select product type 22
- Then to move to next screen 22
- Touch the screen for the type of product required 22
- Select saved product type 23
- To create new program 23
- Confirm setup of machine 24
- Machine is set as shown on the screen this screen controls the actions required by the operator 25
- Operator screen 25
- Program 25
- Start manual 25
- Start stop 25
- Drop with twist 26
- Edit and save screen 26
- Example drop with twist 26
- Save edits 26
- Example 27
- Multidrop with twist 27
- Other setting buttons are the same as last page 27
- Sheeting strip 27
- Example c shape arc 28
- Tray setup 29
- Delete 31
- Caution 32
- Diagnostics 32
- Do not attempt to make adjustments unless you are fully aware of the results 32
- Engineering settings 32
- Passwords 32
- Reset factory defaults 32
- Screen adjustment 32
- Caution 33
- Engineering settings 33
- Caution 34
- Engineering settings 34
- Caution 35
- Engineering settings 35
- Caution 36
- Engineering settings 36
- Gearbox ratios 36
- Rotary 36
- Caution 37
- Engineering settings 37
- Jog speed 37
- Rotary speed 37
- Tray speed 37
- Wipe back default settings see 5a 37
- Fault information screens 38
- Maintenance 40
- Warning do not under any circumstances use a water hose or pressure washer to clean this machine 40
- Check and maintenance schedule 41
- Mono omega touch 41
- Under no circumstances should maintenance or cleaning of this machine be done with the power connected 41
- Email spares monoequip com web site www monoequip com 42
- Main tel 44 0 1792 561234 42
- Spares and service 42
- Spares tel 44 0 1792 564039 42
- Uk service spares and overseas support 42
- Spares 43
- Touch version 43
- Electrical component layout parts 44
- Mechanical component layout parts 45
- Omega touch 45
- Rear view with cover rear view with cover removed 45
- Rear view with cover removed 45
- Base machine spares list 46
- Hard dough hopper parts 47
- Omega touch 47
- Omega touch 48
- Soft dough hopper parts 48
- Electrical information 49
- Touch version 49
- Queensway swansea west industrial estate swansea sa5 4eb uk tel 44 0 1792 561234 fax 44 0 1792 561016 spares 44 0 1792 564039 email marketing monoequip com 63
- The equipment mentioned in this manual has ce accreditation 63
- Web site www monoequip com 63
Похожие устройства
- Mono Omega Touch 400 Брошюра
- Mono Omega Touch 450 Инструкция по эксплуатации
- Mono Omega Touch 450 Брошюра
- Mono Omega Plus 450 (струнная резка) Инструкция по эксплуатации
- Mono Omega Plus 450 (струнная резка) Брошюра
- Mono Omega Plus 400 (твердое тесто) Инструкция по эксплуатации
- Mono Epsilon 450 Инструкция по эксплуатации
- Mono Epsilon 450 Брошюра
- Mono Epsilon 400 Инструкция по эксплуатации
- Mono Epsilon 400 Брошюра
- Gemm ARG/41 Инструкция по эксплуатации
- Gemm ARG/41 Каталог оборудования Gemm
- Gemm ARG/40 Инструкция по эксплуатации
- Gemm ARG/40 Каталог оборудования Gemm
- Gemm TAL/16S Инструкция по эксплуатации
- Gemm TAL/16S Каталог оборудования Gemm
- Gemm TAL/16A Инструкция по эксплуатации
- Gemm TAL/16A Каталог оборудования Gemm
- Gemm TAL/27 Инструкция по эксплуатации
- Gemm TAL/27 Каталог оборудования Gemm