Home
Главная
GRAPHITE
Аккумуляторная Угловая Шлифмашина
58G003
Инструкция по эксплуатации Страница: 15

GRAPHITE 58G003 Инструкция по эксплуатации онлайн [15/144] 320656

that is unguarded and facing the operator is reduced

to minimum. The guard protects the operator from splinters,

accidental contact with the grinding wheel, and sparks that

otherwise could light up clothes.

• Use grinding wheels only for tasks they are designed for.

• For example, do not use side surface of a cutting wheel for

grinding. Grinding wheels for cutting are designed to remove

material with wheel edge. Side forces applied to the wheel may

cause it to crack.

• Always use undamaged fixing flanges with size matching

to the grinding wheel. Proper flanges support grinding wheel

and reduce risk of breaking. Grinding wheels for cutting use

flanges that may be different from flanges designed for other

types of grinding wheels.

• Do not use worn out grinding wheels from bigger devices.

Grinding wheels for bigger devices are not designed for higher

rotational speed, which is specific for smaller devices, and

therefore they may break.

ADDITIONAL DETAILED SAFETY GUIDELINES FOR CUTTING

WITH A GRINDING WHEEL

• Avoid jamming of cutting wheel and excessive pressure.

Do not make too deep cuts. Overloading the cutting wheel

increases its load and risk of jamming or locking, and in

consequence kick back or wheel breaking.

• Avoid areas in front and behind rotating cutting wheel. In

the event of kick back, cutting wheel advance in work piece away

from you may cause bouncing of the device with rotating wheel

towards your hand.

• In the event of jamming of cutting wheel or having a break

in work, switch off the device and wait until the wheel

comes to complete stop. Never attempt to remove rotating

wheel from cut material, as this may cause kick back. Find

and remove cause of jamming.

• Do not switch on the device back, when it is still in

processed material. Before cutting again, cutting

wheel should reach its full rotational speed.

Otherwise the cutting wheel may catch material, bounce out of

work piece or cause kick back.

• Support sheets and large objects before processing to

minimise risk of kick back caused by jammed blade. Large

objects can bend under own weight. Support work piece on both

sides, at cutting line and near edge.

Be careful when cutting holes in walls and operating in other

areas with reduced visibility. Wheel plunging into material may

cause kick back after hitting gas lines, water pipes, electric wires

and other objects.

DETAILED SAFETY GUIDELINES FOR PAPER SANDING

• Do not use too large sheets of abrasive paper. When choosing

size of abrasive paper follow manufacturer instructions.

Abrasive paper that protrudes beyond sanding pad may cause

injuries, and also lead to locking or tearing abrasive paper or kick

back.

DETAILED SAFETY GUIDELINES FOR WIRE BRUSHING

• Remember that brush loses pieces of wire even during

normal use. Do not overload wires by excessive pressure.

Flying pieces of wire can easily penetrate through thin clothes

and/or skin.

• Whenever use of guard is recommended, avoid contact

of brush and guard. Diameter of wheel and cup brushes may

increase at pressure and centrifugal forces.

• Always wear protective glasses when using wire brushes.

ADDITIONAL SAFETY GUIDELINES

• Remove the battery from the device before any equipment

installation.

• Check grinding tools before use. Grinding tool must be

installed properly and must be free to rotate. To check the

device, start it, keep in safe position and let it run with no

load for at least one minute. Do not use damaged or vibrating

grinding tools. Grinding tools must be round. Damaged

grinding tools can break and cause injuries.

• After grinding tool installation, and before starting the

grinder, make sure the grinding tool is properly xed, it is free

to rotate and does not come in contact with the shield.

• Spindle lock button can be activated only when the grinder

spindle is not moving.

• When using tools designed for grinding wheels with threaded

hole, make sure that the length of the wheel thread matches

the length of the spindle thread.

• Secure processed material. Secured material in a xing tool or

a vice is safer than holding it in hand.

• Fix processed material securely if its own weight does not

guarantee stable position.

• Do not touch cutting and grinding wheels before they cool

down.

• Do not apply side force on grinding or cutting wheel.

Do not cut processed material thicker than maximum cutting

depth of cutting wheel.

• When a quick release ange is used, make sure that inner

ange seated on the spindle is equipped with rubber O-ring

and this ring is not damaged. Also surfaces of the outer ange

and the inner ange must be clean.

• Use quick release ange only with cutting and grinding

wheels. Use only anges that are free from defects, that

operate correctly.

CORRECT OPERATION AND USE OF BATTERIES

• Battery charging process should be supervised by the user.

• Avoid charging the battery in temperature lower than 0°C.

• Use only the charger recommended by the manufacturer.

Using charger designed for other type of battery brings the risk

of fire.

• When the battery is not in use, store it away from metal

objects such as paper clips, coins, keys, nails, screws or any

other small metal objects that can short-circuit the battery

connectors. Short-circuit of battery connectors may cause burns

or fire.

• In case of battery damage and/or improper use it may

produce gas. Ventilate room and seek medical attention in

case of medical symptoms. Gas can damage respiratory tract.

• In extreme conditions liquid may leak out of the battery.

The liquid coming out of the battery may cause irritations

or burns. When a leak is found, follow the below procedure:

- Carefully wipe the liquid with a cloth. Avoid contact of the liquid

with skin and eyes.

- In case the liquid gets onto skin, immediately wash the spot

abundantly with clean water, you can also neutralize the liquid

with a mild acid, e.g. lemon juice or vinegar.

- When the liquid gets into eyes, wash it immediately with a lot of

clean water for at least 10 minutes. Seek medical advice.

• Do not use damaged or modified battery. Damaged or

modified batteries may behave unpredictably, causing fire,

explosion or risk of injuries.

• Do not expose the battery to humidity or water.

• Always keep the battery away from sources of heat. Do not

leave the battery for a long time in high temperature (in

direct sunlight, in proximity of heaters and wherever the

temperature exceeds 50°C).

• Do not expose the battery to fire or excessive temperature.

Exposure to re or temperature above 130°C may cause explosion.

GRAPHITE 58G003 Инструкция по эксплуатации онлайн [15/144] 320656

Содержание

Похожие устройства