![Fluke 729 [11/46] Mechanical specification](/img/pdf.png)
Fluke 729 [11/46] Mechanical specification
![Fluke 729 [11/46] Mechanical specification](/views2/1436127/page11/bgb.png)
Automatic Pressure Calibrators
Specifications
7
Mechanical Specification
Size (H x W x L) ........................................ 7.0 cm x 27.9 cm x 17.3 cm
(2.75 in x 11.0 in x 6.8 in)
Weight ....................................................... 2.95 kg (6.5 lb)
Environmental Specification
Operating Temperature ............................. -10 °C to +50 °C for measurement,
0 °C to 50 °C for pressure control
Battery will only charge from 0 °C to 40 °C
Operating Temperature with Battery ......... -10 °C to +40 °C
Storage Temperature ................................ -20 °C to +60 °C
Operating Altitude ...................................... 3000 m
Storage Altitude ......................................... 13 000 m
Operating Humidity .................................... Non condensing (<10 °C)
≤90 % RH (at 10 °C to 30 °C)
≤75 % RH (at 30 °C to 40 °C)
≤45 % RH (at 40 °C to 50 °C)
Safety
General ...................................................... IEC 61010-1, Pollution Degree 2, IEC
61010-2-030: 30 V max
Ingress Protection ..................................... IEC 60529: IP54 (with all port seals
properly fitted)
Lithium Battery .......................................... IEC 62133, UN 38.3; 14.4 V, 6.7Ah,
97Wh, 4ICR19/66-2 (4s2p) Charge
input 19.5 V, 1.6 A.
Electromagnetic Compatibility (EMC)
International ........................... IEC 61326-1: Basic Electromagnetic Environment;
CISPR 11: Group 1, Class A
Group 1: Equipment has intentionally generated
and/or uses conductively-coupled radio frequency
energy that is necessary for the internal function
of the equipment itself.
Class A: Equipment is suitable for use in all
establishments other than domestic and those
directly connected to a low-voltage power supply
network that supplies buildings used for domestic
purposes. There may be potential difficulties in
ensuring electromagnetic compatibility in other
environments due to conducted and radiated
disturbances.
Caution: This equipment is not intended for use in
residential environments and may not provide
adequate protection to radio reception in such
environments.
Содержание
- 729 fc 1
- 729 fc calibration manual 1
- Warranty 2
- Table of contents 3
- Contact fluke 5
- Introduction 5
- Safety 6
- Warnings and cautions 6
- Xw warning 6
- Symbols 8
- Electrical specification 9
- Pressure specification 9
- Specifications 9
- 729 fc 10
- Jp 2m fc 10
- Product models 10
- Environmental specification 11
- Mechanical specification 11
- Safety 11
- 729 fc 12
- An exempt device per clause 15 03 non fc versions only 12
- Class a equipment meets requirements for class a equipment meets requirements for industrial electromagnetic wave equipment and the seller or user should take notice of it this equipment is intended for use in business environments and not to be used in homes 12
- Communication equipment 12
- Fluke recommends re certification each year to re certify do the verification procedure if test points are out of tolerance calibrate the product and then re verify 12
- Korea kcc class a equipment industrial broadcasting 12
- Performance verification tests 12
- Radio certification contains fcc id t68 fble ic 6627a fble frequency 2402 mhz to 2480 mhz output power 100 mw 12
- The equipment necessary for verification of the product is shown in table 2 if these instruments are not available you can replace them with other source and measure instruments that have the same the minimum specification requirements 12
- Usa fcc 47 cfr 15 subpart b this product is considered 12
- Use the subsequent tests to make sure that the product is inside its specification limits 12
- Verification equipment 12
- How to verify 13
- Pressure verification 13
- Verification procedures 13
- 729 fc 14
- Automatic pressure calibrators 15
- 729 fc 16
- Automatic pressure calibrators 17
- Connect the product black banana jack com to the 5522a lo volts 17
- Connect the product red banana jack v ma to the 5522a hi volts output 17
- Dc voltage measure verification 17
- On the product 17
- Output 17
- Push measure vdc shows in the second row of the display 17
- Set the 5522a for the voltage setting in table 4 and verify the display reading 17
- Set the 5522a to standby 17
- To verify the dc voltage measure function see figure 1 17
- 729 fc 18
- Connect the product as shown in figure 2 18
- Correct value shows on the 8508a 18
- Dc current measure verification 18
- Push measure current shows in the second row of the display 18
- Repeat for each applied value in table 5 18
- Set the 5522a to standby 18
- Set the 5522a to the first test point in table 5 and edit its output so that the 18
- To verify the dc current measure function 18
- Verify the display reading on the product 18
- Automatic pressure calibrators 19
- Figure 2 dc current measure verification connections 19
- Ien002 eps 19
- Performance verification tests 19
- 729 fc 20
- Connect the product black banana jack com to the 8508a lo ma input 20
- Connect the product red banana jack v ma to the 8508a hi ma input 20
- Dc current source verification 20
- Enter the current setting in table 6 and push 20
- Highlight measure current 20
- Move the cursor to highlight the ma value 20
- Push to switch to ma measure mode to exit the current source function 20
- Push to switch to the source current function 20
- Set the 8508a for the amp setting 20
- To verify the dc current source function see figure 3 20
- Use the arrow keys to move the cursor to second row of the display and 20
- Verify the display reading on the product 20
- Automatic pressure calibrators 21
- Connect the 720urtda current hi to the 5522a hi rtd output 21
- Connect the 720urtda current lo to the 5522a lo rtd output 21
- Connect the 720urtda sense hi to the 5522a hi rtd output 21
- Connect the 720urtda sense lo to 5522a lo rtd output 21
- Connect the 720urtda to the product 21
- Rtd measure verification 21
- Set the 5522a to pt385 rtd 4 wire comp temperature settings in table 7 21
- To verify the rtd measure function see figure 4 21
- Verify that the display reading on the product is within the limits 21
- When the product detects temperature from the rtd connector it turns on a temperature display 21
- V loop power performance check 22
- Calibration adjustment 23
- Calibration data 23
- Manual process front panel 23
- Service center calibration or repair 23
- Adjust pressure 24
- Electronic calibration process remote 24
- Automatic pressure calibrators 25
- To adjust the pressure function follow the procedures in tables 9 10 and 11 25
- 729 fc 26
- Automatic pressure calibrators 27
- 729 fc 28
- Automatic pressure calibrators 29
- 729 fc 30
- Adjust voltage input 30
- The test equipment to adjust the voltage input is listed in table 12 30
- Adjust ma input 31
- All reference actual values that you input during the calibration procedure should be the reading from 8508a 31
- Automatic pressure calibrators 31
- The test equipment to adjust the ma input is listed in table 14 31
- Use the test procedure in table 13 to adjust the voltage input 31
- 729 fc 32
- Adjust ma source 32
- Table 16 is a list of the the test equipment to adjust the ma source 32
- Use the test procedure in table 15 to adjust the ma input 32
- Adjust rtd 33
- Automatic pressure calibrators 33
- Table 18 is a list of the test equipment to adjust the rtd 33
- Use the test procedure in table 17 to adjust the ma source 33
- 729 fc 34
- Adjust continuity 34
- All reference actual values the you input during the calibration procedure should be the reading from 8508a 34
- Table 20 lists the test equipment to test continuity 34
- Use the test procedure in table 19 for rtd adjustment 34
- Automatic pressure calibrators 35
- Use the test procedure in table 21 for continuity adjustment 35
- Calibration remote commands 36
- 729 fc 38
- Calibration manual 38
- Example 38
- Charge the battery 39
- The battery 39
- Battery life 40
- Battery replacement 40
- Automatic pressure calibrators 41
- Clean the product 42
- Clean the pump valve 42
- Maintenance 42
- Xw warning 42
- Replace the pump filters 43
- 729 fc 44
- In case of difficulty 45
- Update product firmware 45
- Xw warning 45
- 729 fc 46
- Table 23 is a list of replacement parts and accessories 46
- User replaceable parts and accessories 46
Похожие устройства
- Fluke 729 Pressure Calibration APPLICATIONS AND SOLUTIONS
- Fluke 729 FC Приложение к руководству по калибровке
- Fluke 729 FC Pressure Pain Points Brochure, RU
- Fluke 729 FC 729 Pressure Calibrator _ Спецификация
- Fluke 729 FC Power facility reduces pressure maintenance costs with the Fluke 729
- Fluke 729 FC Положение об энергозависимости памяти
- Fluke 729 FC Приложение к Руководству по эксплуатации
- Fluke 729 FC Radio Frequency Data Class B _ Инструкция
- Fluke 729 FC Краткий справочник
- Fluke 729 FC Паспорт безопасности
- Fluke 729 FC Pressure Calibration APPLICATIONS AND SOLUTIONS
- Fluke 729 FC Руководство по калибровке
- Fluke 719 Pro Положение об энергозависимости памяти
- Fluke 719 Pro Руководство по калибровке
- Fluke 719 Pro Data Sheet
- Fluke 719 Pro Приложение к Руководству по эксплуатации
- Fluke 719 Pro Паспорт безопасности
- Fluke 719 Pro Руководство по эксплуатации
- Fluke 719 Pro Premium Pressure Accessory Kit _ Краткий справочник
- Fluke 719 Pro Pressure Calibration APPLICATIONS AND SOLUTIONS