Ariens ST28DLET PRO TRACK [18/38] Pre start
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Ariens ST28DLET PRO TRACK [18/38] Pre start

Ariens ST28DLET PRO HYDRO TRACK [18/38] Pre start
EN - 18
Fuel Shut-Off Valve
IMPORTANT: The fuel shut-off valve MUST
be in the closed position prior to transporting
the unit.
The fuel shut-off valve
has two positions:
Open (1): Use this
position to run the unit.
Closed (2): Use this
position to service,
transport, or store the
unit.
PRE-START
1. Frozen Impeller
IMPORTANT: Before starting engine, check
impeller to be sure it is not frozen.
To check impeller:
1. With ignition key switch in “Stop”
position, squeeze Attachment Clutch
Lever to Engaged position.
2. Pull Recoil Starter Handle.
3. If Impeller is frozen, (cannot pull Starter
Handle) move unit to a heated area and
thaw to prevent possible damage.
2. Check Function of Clutches
If clutches do not engage or disengage
properly, adjust or repair before operation.
See Attachment Clutch/Brake Adjustment on
page 25 and Traction Drive Clutch
Adjustment on page 27.
3. Check Dual Handle Interlock
Without the engine running, press down
(engage) both clutch levers. Release
attachment clutch lever. Attachment clutch
should remain engaged until traction clutch
lever is released, then both clutches must
disengage.
If clutches do not engage or disengage
properly, adjust or repair before operation.
See Attachment Clutch/Brake Adjustment on
page 25 and Traction Drive Clutch
Adjustment on page 27.
4. Check Axle Lock
(926056)
Use the axle lock knob to lock or unlock the
right side differential. Lock the differential to
engage both tracks and increase traction;
unlock the right side to allow for easier
turning of the unit (see Differential Lock on
page 15).
5. Check Skid Shoes
Check and adjust Skid Shoes (See Skid
Shoes on page 23). Allow 1/8 in. (3 mm)
between scraper blade and hard, smooth
surface(s). Allow 7/8 in. (22mm) between
scraper blade and uneven or gravel surfaces.
Check Engine Fuel & Crankcase Oil
Check and add fuel if required. Check that
the engine crankcase oil is full using dipstick.
Refer to Engine Manual for detailed
instructions.
TO STOP IN AN EMERGENCY
Immediately release both control levers to
stop unit in an emergency. Stop engine,
remove key and wait for all rotating parts to
stop before leaving operator’s position.
STARTING AND SHUT OFF
IMPORTANT: Allow unit and engine to adjust
to the outdoor temperature before clearing
snow. Before shut-off, run the attachment a
few minutes to prevent impeller freeze-up.
NOTE: Try out each control without the
engine running to see how it works and what
it does.
Manual Start
1. Turn discharge chute straight ahead.
2. Make sure that the traction clutch and
attachment drive clutch levers are fully
disengaged.
3. Push Primer Bulb 2 or 3 times for cold
engine.
NOTE: When temperature is below -15° F
(-26° C) additional priming may be needed.
4. If engine is cold, apply choke. See
Engine Manual for detailed instructions.
NOTE: A warm engine requires less choking
than a cold engine.
5. Set throttle to proper starting position.
6. Turn on engine shut-off switch ("ON").
7. Insert key into ignition switch and turn to
"Run" position.
1
2
WARNING: AVOID INJURY. Read
and understand the entire Safety
section before proceeding.
WARNING: FAILURE TO FOLLOW
INSTRUCTIONS could result in
personal injury and/or damage to
unit. DO NOT attempt to start your
unit at this time. Read entire
Owner/Operator Manual and the
Engine Manual first.

Содержание

Похожие устройства

Скачать